ASTM D2661-2006 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain Waste and Vent Pipe and Fittings《丙烯腈-丁二烯-苯乙烯共聚物(ABS)塑料排水管、污水管和通气管及其配件的标准规.pdf
《ASTM D2661-2006 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain Waste and Vent Pipe and Fittings《丙烯腈-丁二烯-苯乙烯共聚物(ABS)塑料排水管、污水管和通气管及其配件的标准规.pdf》由会员分享,可在线阅读,更多相关《ASTM D2661-2006 Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain Waste and Vent Pipe and Fittings《丙烯腈-丁二烯-苯乙烯共聚物(ABS)塑料排水管、污水管和通气管及其配件的标准规.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D 2661 06An American National StandardStandard Specification forAcrylonitrile-Butadiene-Styrene (ABS) Schedule 40 PlasticDrain, Waste, and Vent Pipe and Fittings1This standard is issued under the fixed designation D 2661; the number immediately following the designation indicates the ye
2、ar oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Depart
3、ment of Defense.1. Scope1.1 This specification covers fittings and single and coex-truded acrylonitrile-butadiene-styrene (ABS) plastic drain,waste, and vent pipe (DWV) made to Schedule 40 iron pipesizes (IPS). Plastic which does not meet the material require-ments specified in Section 5 is excluded
4、 from single layer andall coextruded layers.1.2 Specification for fittings for use with pipe meeting therequirements of this specification are given in Annex A1.1.3 Acrylonitrile-butadiene-styrene plastic, which does notmeet the definition of virgin ABS plastic as given in 3.2.2,isexcluded, as perfo
5、rmance of plastic other than those defined asvirgin was not determined. ABS rework plastic, which meetsthe requirements of rework plastic as given in 5.3, is accept-able.1.4 Reprocessed plastic or recycled plastic as defined inTerminology D 883 is excluded.1.5 Recommendations for storage, joining, a
6、nd installationare provided inAppendix X1,Appendix X2, andAppendix X3,respectively.1.6 The text of this specification references notes, footnotes,and appendixes which provide explanatory material. Thesenotes and footnotes (excluding those in tables and figures) shallnot be considered as requirements
7、 of the specification.1.7 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.2. Referenced Documents2.1 ASTM Standards:2D 618 Practice for Conditioning Plastics for TestingD 883 Terminology Relating to PlasticsD 1600 Termi
8、nology for Abbreviated Terms Relating toPlasticsD 1898 Practice for Sampling of Plastics3D 2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD 2135 Classification of Hard Rubber Materials3D 2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) P
9、lastic Pipe and FittingsD 2321 Practice for Underground Installation of Thermo-plastic Pipe for Sewers and Other Gravity-Flow Applica-tionsD 2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD 2444 Test Method for Determination of the Impa
10、ct Re-sistance of Thermoplastic Pipe and Fittings by Means of aTup (Falling Weight)D 3311 Specification for Drain, Waste, and Vent (DWV)Plastic Fittings PatternsD 3965 Specification for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and FittingsE 105 Practice for Probability Sampling
11、 Of MaterialsE 122 Practice for Calculating Sample Size to Estimate,With a Specified Tolerable Error, the Average for aCharacteristic of a Lot or ProcessF 402 Practice for Safe Handling of Solvent Cements,Primers, and Cleaners Used for Joining Thermoplastic Pipeand FittingsF 412 Terminology Relating
12、 to Plastic Piping SystemsF 1498 Specification for Taper Pipe Threads 60 for Ther-moplastic Pipe and FittingsF 2135 Specification for Molded Drain, Waste, and Vent(DWV) Short-Pattern Plastic Fittings2.2 Federal Standard:Fed. Std. No. 123 Marking for Shipment (Civil Agencies)42.3 Military Standard:1T
13、his specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.Current edition approved Nov. 1, 2006. Published November 2006. Originallyapproved in 1967. Last previous edition approved in 2002 as D 2661 02.2F
14、or referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from Standardization Documents Order Desk
15、, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.MIL-STD-129 Marking for Shipment and Storage43. Terminology3.1 DefinitionsDefinitions are in accordance wi
16、th Termi-nology F 412, and abbreviations are in accordance with Ter-minology D 1600, unless otherwise specified. The abbreviationfor acrylonitrile-butadiene-styrene is ABS.3.1.1 coextruded pipepipe consisting of two or moreconcentric layers of material bonded together in processing byany combination
17、 of temperature, pressure, grafting, crosslink-ing, or adhesion.3.1.2 coextrusiona process whereby two or more heatedor unheated plastic material streams forced through one ormore shaping orifice(s) become one continuously formedpiece.3.1.3 room temperaturea temperature in the range from68 to 85 6 3
18、.6F (20 to 30 6 2C).3.2 Definitions of Terms Specific to This Standard:3.2.1 lota lot shall consist of all pipe of the same sizeproduced from one extrusion line during one designated 24-hperiod.3.2.2 recycled plastica plastic prepared from discardedarticles that have been cleaned and reground.3.2.3
19、reprocessed plastica thermoplastic usually preparedfrom melt processed scrap or reject parts by a plasticsprocessor, or from nonstandard or nonuniform virgin material.3.2.4 virgin ABS plasticplastic in the form of pellets,granules, powder, floc, or liquid that has not been subjected touse or process
20、ing other than that required for its initialmanufacture.4. Classification4.1 The requirements of this specification are intended toprovide pipe suitable for the drainage and venting of sewageand certain other liquid wastes.NOTE 1Industrial waste disposal lines should be installed only withthe specif
21、ic approval of the cognizant building code authority sincechemicals not commonly found in drains and sewers and temperatures inexcess of 180F (82C) may be encountered.5. Materials5.1 Material SpecificationVirgin black ABS plastic shallconform to the requirements prescribed in SpecificationD 3965 wit
22、h a cell classification of 4-2-2-2-2. The form of thematerial shall be as agreed upon between the seller and thepurchaser in accordance with Specification D 3965.5.2 The ABS plastic shall conform to the following require-ments:5.2.1 Acrylonitrile-Butadiene-Styrene (ABS) PlasticPlastic containing pol
23、ymers or blends of polymers shall containa minimum of 15 % acrylonitrile, 6 % butadiene, and 15 %styrene or substituted styrene, or both. ABS plastic shallcontain no more than 10 % of other monomeric or polymericcomponents plus other necessary compounding ingredients.5.3 Rework MaterialThe manufactu
24、rer shall use only hisown clean pipe or fitting rework material conforming withthese cell class requirements. The pipe or fittings producedshall meet all the requirements of this specification.6. Requirements6.1 GeneralThe pipe and fittings shall be homogeneousthroughout and free of visible cracks,
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD26612006STANDARDSPECIFICATIONFORACRYLONITRILEBUTADIENESTYRENEABSSCHEDULE40PLASTICDRAINWASTEANDVENTPIPEANDFITTINGS

链接地址:http://www.mydoc123.com/p-513264.html