ASTM D322-1997(2012) Standard Test Method for Gasoline Diluent in Used Gasoline Engine Oils by Distillation《通过蒸馏法测定汽油发动机废机油中汽油稀释剂的标准试验方法》.pdf

《ASTM D322-1997(2012) Standard Test Method for Gasoline Diluent in Used Gasoline Engine Oils by Distillation《通过蒸馏法测定汽油发动机废机油中汽油稀释剂的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D322-1997(2012) Standard Test Method for Gasoline Diluent in Used Gasoline Engine Oils by Distillation《通过蒸馏法测定汽油发动机废机油中汽油稀释剂的标准试验方法》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D322 97 (Reapproved 2012)Designation: 23/2000Standard Test Method forGasoline Diluent in Used Gasoline Engine Oils byDistillation1This standard is issued under the fixed designation D322; the number immediately following the designation indicates the year oforiginal adoption or, in the

2、case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This te

3、st method covers determination of the amount ofdilution in crankcase oils of engines when gasoline has beenused as the fuel.NOTE 1There may be cases in dispute, therefore, the user of this testmethod is advised to establish whether this method will be accepted. Theremay be cases where Test Method D3

4、525 results will be set as the refereevalue.1.2 The values stated in acceptable SI units are to beregarded as the standard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro

5、-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. For specificprecautionary statement, see 6.4, 7.1, and 9.3.2. Referenced Documents2.1 ASTM Standards:2D235 Specification for Mineral Spirits (Petroleum Spirits)(Hydrocarbon Dry Cleaning Solve

6、nt)D3525 Test Method for Gasoline Diluent in Used GasolineEngine Oils by Gas ChromatographyD4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4175 Terminology Relating to Petroleum, PetroleumProducts, and LubricantsD4177 Practice for Automatic Sampling of Petroleum andPetroleum Pr

7、oducts2.2 IP Methods for Analyses and Testing, Vol II, Part I33. Terminology3.1 Definitions:3.1.1 fuel diluent, nin used oil analysis, unburnt fuelcomponents that enter the engine crankcase causing dilution ofthe oil.3.1.1.1 DiscussionIn this test method, the fuel diluentcomponents being determined

8、are from gasoline.3.1.2 used oil, nany oil that has been in a piece ofequipment (for example, an engine, gearbox, transformer, orturbine) whether operated or not. D41753.1.2.1 DiscussionIn this test method, used oil is from agasoline engine.4. Summary of Test Method4.1 The sample, mixed with water,

9、is placed in a glass stillprovided with a reflux condenser discharging into a graduatedtrap connected to the still. Heat is applied, and the contents ofthe still are brought to boiling. The diluent in the sample isvaporized with the water and then liquefied in the condenser.The diluent collects at t

10、he top of the trap, and the excess waterruns back to the still where it is again vaporized, carrying overan additional quantity of diluent. The boiling is continued untilall the diluent has been boiled out and recovered in the trap.The volume is recorded.5. Significance and Use5.1 Some fuel dilution

11、 of the engine oil may take placeduring normal operation. However, excessive fuel dilution is ofconcern in terms of possible performance problems.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.

12、06 on Analysis of Lubricants.This test method was adopted as a joint ASTM-IP standard in 1964. In the IP, thismethod is under the jurisdiction of the Standardization Committee.Current edition approved Nov. 1, 2012. Published November 2012. Originallyapproved in 1930. Last previous edition approved i

13、n 2007 as D322 97 (2012).DOI: 10.1520/D0322-97R12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available

14、from Energy Institute, 61 New Cavendish St., London, WIG 7AR,U.K., http:/www.energyinst.org.uk.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16. Apparatus6.1 Flask, round-bottom type (see Fig. 1 and A1.1).6.2 Condenser, Liebig straig

15、ht-tube type (see A1.2).6.3 Trap, 5 mL, graduated in 0.1-mL increments (see Fig. 1and Fig. 2 and A1.3).6.4 HeaterAny suitable gas burner or electric heater maybe used with the glass flask. (WarningHot exposed surface.Avoid contact by wearing protective equipment as required.)7. Reagents and Material

16、s7.1 Ethanol, Denatured , conforming to either Formula No.30 or 3A of the US Bureau of Internal Revenue. (WarningFlammable. Denatured. Cannot be made non-toxic.)7.2 Mineral Spirits (Petroleum Spirits), conforming toSpecification D235.NOTE 2In Annex A1.3, the use of reagent grade heptane may be thepr

17、eferred solvent because the use of commerical grade heptane or mineralspirits can cause complications of container disposal that may not berequired for the disposal of the containers for reagent grade heptane.8. Sampling8.1 Obtain a representative sample using either PracticesD4057 or D4177.9. Proce

18、dure9.1 Mix the sample thoroughly, measure 25 6 5mLbymeans of a 25-mL graduated cylinder, and transfer as much aspossible of the contents of the cylinder by pouring it into theflask. Wash the graduated cylinder with successive portions ofhot water until only a negligible amount of oil is left in the

19、cylinder. Add additional water to the flask to make a total ofapproximately 500 mL of water. Fill the trap with cold waterand add 1 6 0.1 mL of denatured ethanol to the water in thetrap.9.2 Assemble the apparatus as shown in Fig. 1, so that thetip of the condenser is directly over the indentation in

20、 the trap.9.3 Apply heat to the flask at such a rate that refluxing startswithin 7 to 10 min after heat is applied, with the water andsample being at 21 to 38C prior to application of heat. Afterboiling and condensation has commenced, adjust the rate ofboiling so that condensed distillate is dischar

21、ged from thecondenser at a rate of 1 to 3 drops per s. (Warning Hotexposed surface. Avoid contact by wearing protective equip-ment as required. )NOTE 3Bumping with a tendency to froth over is often experiencedwith dirty oils. The use of boiling stones, steel wool, or about 5 mL ofconcentrated hydroc

22、hloric acid (HCl) in the flask is often helpful ineliminating this difficulty.9.4 Obtain readings of the amount of diluent at the follow-ing times, taken from the time that refluxing starts: 5, 15, and30 min, 6 1 min, and each 15 min, 6 1 min, following untilthe test is complete. Completion of the t

23、est shall be determinedon the basis of either or both of the following criteria:9.4.1 The test is complete when the volume of diluentincreases by not more than 0.1 mL in any 15-min period duringthe course of the test.FIG. 1 Apparatus for Determining Diluent in Gasoline Engine Crankcase OilD322 97 (2

24、012)29.4.2 The test is complete when the volume of diluentobtained in a given time indicates completion, as follows:Time from Start ofRefluxingTest is Complete if ApparentVolume of Diluent Collected isEqual to or Less Than:5 min no visible diluentA30 min 2.0 mL60 min 4.0 mL90 min 5.0 mLAReport as “n

25、o dilution;” otherwise the test should be continued at least 30 min.9.5 When the test continues without reaching the limitdefined in 9.4.1, to a point at which any of the conditionsdescribed in 9.4.2 are encountered, the latter shall define thecompletion of the test.9.6 When the test is complete by

26、either of the criteriadefined in 9.4.1 and 9.4.2, turn off the heat. Allow theequipment to stand for at least 30 min to allow the distillate toseparate completely and to cool to approximately room tem-perature. Read the volume of diluent collected in the trap. If thevolume of diluent exceeds the cal

27、ibrated capacity of the trap,discontinue the test and report the results as 20 % plus.10. Calculation10.1 The diluent content of the sample, expressed as volumepercent, is equal to the volume of diluent in millilitresmultiplied by 4.NOTE 4In some cases with samples containing large amounts ofdiluent

28、, equipment limitations do not permit collection and measurementof the full 5 mL of diluent even when more is present. This conditionexists when the upper limit of the collected diluent is above the zerocalibration mark on the trap. When it occurs, finish the test as prescribedin 9.6, read the maxim

29、um volume of diluent collected, calculate thecorresponding percentage x, and report the results as x percent plus.11. Report11.1 Report the result as the Diluent Content, ASTMD322 IP 23.12. Precision and Bias12.1 The precision of this test method as obtained bystatistical examination of interlaborat

30、ory test results is asfollows:12.1.1 RepeatabilityThe difference between successivetest results, obtained by the same operator with the sameapparatus under constant operating conditions of identical testmaterial, would in the long run, in the normal and correctoperation of the test method, exceed th

31、e following value onlyin one case in twenty:0.6 volume% (1)12.1.2 ReproducibilityThe difference between two singleand independent results, obtained by different operators work-ing in different laboratories on identical test material would inthe long run, in the normal and correct operation of the te

32、stmethod, exceed the following value only in one case in twenty:1.4 volume% (2)12.2 BiasThe procedure in this test method has no biasbecause the volume percent of gasoline diluent can only bedefined in terms of this test method.13. Keywords13.1 distillation; engine oils; gasoline distillation; usedA

33、ll dimensions are in millimetresFIG. 2 Alternate Closures for Diluent TrapD322 97 (2012)3ANNEX(Mandatory Information)A1. APPARATUSA1.1 Flask, round-bottomed, short-necked, having a nomi-nal capacity of 1 L. Fig. 1 and Fig. 2 show recommendeddesigns and glass connections.A1.2 Condenser , Liebig strai

34、ght type with a jacket not lessthan 400 mm long, and with an inner tube having an outsidediameter of 10 to 13 mm. Fig. 1 and Fig. 2 show characteristicdetails of suitable condensers.A1.3 Trap, in accordance with the details of constructionshown in Fig. 1 and Fig. 2, and conforming to the followingre

35、quirements: It shall be graduated from 0 to 5 mL in 0.1-mLdivisions. It shall be calibrated at four or more points by firstfilling it with water and then adding Stoddard solvent orn-heptane from a standard buret having a calibrated capacity atleast equal to that of the trap. The Stoddard solvent sho

36、uldconform to Specification D235. The n-heptane should conformto the current IP specification (see 2.1). The error of theindicated volume shall not exceed 0.05 mL.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this s

37、tandard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be re

38、viewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of therespons

39、ible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West

40、Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D322 97 (2012)4