ASTM D2295-1996(2016) Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading at Elevated Temperatures (Metal-to-Metal)《采用高温拉向载荷 (金属对金属) 测定剪切胶粘剂强度性能的标.pdf
《ASTM D2295-1996(2016) Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading at Elevated Temperatures (Metal-to-Metal)《采用高温拉向载荷 (金属对金属) 测定剪切胶粘剂强度性能的标.pdf》由会员分享,可在线阅读,更多相关《ASTM D2295-1996(2016) Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading at Elevated Temperatures (Metal-to-Metal)《采用高温拉向载荷 (金属对金属) 测定剪切胶粘剂强度性能的标.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D2295 96 (Reapproved 2016)Standard Test Method forStrength Properties of Adhesives in Shear by TensionLoading at Elevated Temperatures (Metal-to-Metal)1This standard is issued under the fixed designation D2295; the number immediately following the designation indicates the year oforigin
2、al adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the com-parative she
3、ar strengths of adhesives for bonding metals whentested on a standard specimen and under specified conditions ofpreparation and testing at elevated temperatures.1.2 This test method is applicable to the temperature rangefrom 315 to 850C (600 to 1500F).1.3 The values stated in SI units are to be rega
4、rded as thestandard. The values given in parentheses are for informationonly.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to consult andestablish appropriate safety and health practices
5、and deter-mine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2A167 Specification for Stainless and Heat-ResistingChromium-Nickel Steel Plate, Sheet, and Strip (With-drawn 2014)3D638 Test Method for Tensile Properties of PlasticsD907 Terminology of
6、 AdhesivesD1002 Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Ten-sion Loading (Metal-to-Metal)2.2 Military Specifications:MIL-S-25043 Steel Plate, Sheet, and Strip43. Terminology3.1 Many terms in this test method are defined in Terminol-ogy D907.4.
7、 Significance and Use4.1 Comparative strength of adhesive bonds at elevatedtemperatures allows for better selection of adhesives that mustperform at temperatures above normal. This test method isuseful in supplying such information.5. Apparatus5.1 Testing Machine, conforming to the requirements of T
8、estMethod D638. Use pin-type grips as shown in Fig. 1 to hold thetest specimen.5.2 Heating Equipment, consisting of a radiant heat source,backed by a high-efficiency reflector for the purpose ofobtaining the desired heat flux. A suitable lamp arrangementfor heating a specimen is shown in Fig. 2.6. T
9、est Specimens6.1 Cut test specimens from panels shown in Fig. 3(a).These test specimens form and dimensions are shown in Fig.3(b). The specimens are similar to the tension lap shearspecimen described in Fig. 1 of Test Method D1002, exceptthat pin-type grips are used.6.2 Base the selection of materia
10、ls on the test temperaturerange. The following grades of steel are recommended, al-though use of other types of heat-resistant steel is permitted:Metal DesignationSteel, corrosion-resistant (18-8) plate, sheet, andstripA167, Type 302Steel plate, sheet, and strip 17-7PH, TH 1050,corrosion-resistant,
11、precipitation hardenedMIL-S-25043The nominal thickness for the sheet 1.270 mm (0.050 in.).7. Preparation of Test Specimens7.1 Cut test specimens as shown in Fig. 3(b) to dimensionsfrom the test panel. Measure the width of the specimen and thelength of the overlap to the nearest 0.25 mm (0.01 in.).7.
12、2 Prepare test specimens by bonding individual strips asshown in Fig. 3(b). Machine unbonded individual strips to sizeand free from burrs or other irregularities.1This test method is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.80 on M
13、etalBonding Adhesives.Current edition approved May 1, 2016. Published May 2016. Originallyapproved in 1964. Last previous edition approved in 2008 as D2295 96 (2008).DOI: 10.1520/D2295-96R16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serv
14、iceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from DLA Document Services, Building 4/D, 700 Robbins Ave.,Philadelphia, PA
15、 19111-5094, http:/quicksearch.dla.mil.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States17.3 Uniformly coat both sides of the dummy and testspecimens with carbon black as shown in Fig. 3(b).8. Procedure8.1 Place the specimens in the pin
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD229519962016STANDARDTESTMETHODFORSTRENGTHPROPERTIESOFADHESIVESINSHEARBYTENSIONLOADINGATELEVATEDTEMPERATURESMETALTOMETAL

链接地址:http://www.mydoc123.com/p-511414.html