ASTM D2258 D2258M-2016 Standard Practice for Sampling Yarn for Testing《试验用纱线取样的标准实施规程》.pdf
《ASTM D2258 D2258M-2016 Standard Practice for Sampling Yarn for Testing《试验用纱线取样的标准实施规程》.pdf》由会员分享,可在线阅读,更多相关《ASTM D2258 D2258M-2016 Standard Practice for Sampling Yarn for Testing《试验用纱线取样的标准实施规程》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D2258 99 (Reapproved 2012)D2258/D2258M 16Standard Practice forSampling Yarn for Testing1This standard is issued under the fixed designation D2258;D2258/D2258M; the number immediately following the designation indicatesthe year of original adoption or, in the case of revision, the year o
2、f last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This practice describes a proc
3、edure for the division of shipments of yarn into test lots and the sampling of such lots fortesting.1.1.1 This practice can be used for lot sample testing of yarns for both pre-fabric production and post-fabric production.1.2 This practice is applicable to single, plied, or cabled yarns, and cords,
4、made of any fiber or mixture of fibers, and supportedon any form of package, including beams.1.3 This practice also describes procedures for the sampling of yarn(s) removed from woven or knitted fabrics,fabrics; however,when thus sampled, the yarns are usually not representative of entire shipments,
5、 as referred to in 1.1. Consequently, the resultantsampling can only be used to determine the characteristics of the yarn and is usually not used for acceptance testing. Moreover,it should be recognized that the characteristics of yarns from fabrics may be different than the characteristics of the s
6、ame yarn(s),prior to being entered into the fabric manufacturing process.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as the standard. Within the text, theinch-pound units are shown in parentheses. standard. The values stated in each system aremay not be
7、 exact equivalents; therefore,each system shall be used independently of the other. Combining values from the two systems may result in nonconformancenon-conformance with this practice.the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its
8、use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D123 Terminology Relating to TextilesD1578 Test Method for Breaking Strength
9、 of Yarn in Skein FormD1907 Test Method for Linear Density of Yarn (Yarn Number) by the Skein MethodD4271 Practice for Writing Statements on Sampling in Test Methods for Textiles (Withdrawn 2009)3D4849 Terminology Related to Yarns and Fibers3. Terminology3.1 For terminology related to Yarns and Fibe
10、rs, see Terminology D4849.3.2 The following terms are relevant to this standard: beam, beam set, bulk sample, case, cone, end, fabric package, laboratorysample, lot, lot sample, primary sampling unit, production lot, sample, sampling unit, sample skein, specimen, and yarn package.3.3 For definitions
11、 of all other textile terms see Terminology D123.4. Summary of Practice4.1 Instructions are given for dividing the yarn into lots, for determining the number of cases, beams, or fabric packages to beselected from each lot as a lot sample, and for determining the number of packages, including the num
12、ber of ends, representingthose packages taken from the lot sample as a laboratory sample. See Practice D4271.1 This practice is under the jurisdiction of ASTM Committee D13 on Textiles and is the direct responsibility of Subcommittee D13.58 on Yarns and Fibers.Current edition approved March 1, 2012J
13、uly 1, 2016. Published April 2012August 2016. Originally approved in 1964. Last previous edition approved in 20052012 asD2258 99(2005).(2012). DOI: 10.1520/D2258-99R12.10.1520/D2258_D2258M-16.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serv
14、iceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version.
15、Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 1
16、00 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15. Significance and Use5.1 Assigning a value to any property of the material in a container or in a lot, consignment, or delivery involves a measurementprocess that includes both sampling and testing procedures. The c
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD2258D2258M2016STANDARDPRACTICEFORSAMPLINGYARNFORTESTING 试验 纱线 取样 标准 实施 规程 PDF
链接地址:http://www.mydoc123.com/p-511319.html