ASTM D2097-2003(2010) Standard Test Method for Flex Testing of Finish on Upholstery Leather《家具皮革表层挠曲测试的标准试验方法》.pdf
《ASTM D2097-2003(2010) Standard Test Method for Flex Testing of Finish on Upholstery Leather《家具皮革表层挠曲测试的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM D2097-2003(2010) Standard Test Method for Flex Testing of Finish on Upholstery Leather《家具皮革表层挠曲测试的标准试验方法》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D2097 03 (Reapproved 2010)Standard Test Method forFlex Testing of Finish on Upholstery Leather1This standard is issued under the fixed designation D2097; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last
2、 revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the flex-ibility and adhesion of a finish on upholstery leather.2This testmet
3、hod does not apply to wet blue.1.2 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the
4、 user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3D1610 Practice for Conditioning Leather and Leather Prod-ucts for Testing3. Summary of Test Method3.1 The le
5、ather is mechanically flexed alternately from a flatposition into a single or double bend. At the end of apredetermined number of flexing cycles, the leather is visuallyinspected for finish cracks.4. Significance and Use4.1 This test method simulates the flexing received byupholstery leather in serv
6、ice, and correlation with service isbelieved to be good. Both the resistance of the finish tocracking and adhesion of the finish to the leather can beevaluated.4.2 The flexing action received by the leather in this methodis more severe than that given by methods for shoe upperleather. The less sever
7、e tests have little utility in the evaluationof upholstery leather finishes.4.3 This test method is suitable, and has been useful, inresearch, development, and manufacturing control. It is used asa method of test for specification acceptance. Since this is asubjective test, proper correlation should
8、 be established byinterlaboratory experience prior to use for specification accep-tance.5. Apparatus5.1 Newark Flexing MachineThis machine,4illustrated inFig. 1, consists basically of two pistons, one of which isstationary, the other capable of moving at 500 rpm with astroke of 114 in. (32 mm). The
9、movable piston is alsoadjustable on its shaft in order to vary the distance between thetwo pistons.6. Test Specimen6.1 The test specimen shall be 3 by 412 in. (76 by 114 mm)in size.7. Conditioning7.1 Bring all test specimens to equilibrium as described inPractice D1610. Usually, maintaining the spec
10、imen for 24 hunder these conditions will adequately satisfy the equilibriumconditions.7.2 The test shall also be conducted under the aboveconditions, described in Practice D1610.8. Procedure8.1 Measure the thickness of the specimen to be tested.8.2 While in the closed position, adjust the pistons to
11、 fifteentimes the thickness of the specimen (see Fig. 2).8.3 Turn the pulley by hand until the pistons are themaximum distance apart. Clamp the specimen around the twopistons without stretching the specimen.8.4 Complete the first cycle by turning the pulley by handand forcing the specimen into its f
12、lexing pattern (Fig. 3 andNote 1).NOTE 1The flexing pattern is achieved as follows: Facing the center1This test method is under the jurisdiction of ASTM Committee D31 on Leatherand is the direct responsibility of Subcommittee D31.05 on Upholstery. This testmethod was developed in cooperation with th
13、e American Leather Chemists Assn.Current edition approved April 1, 2010. Published May 2010. Originallyapproved in 1962. Last previous edition approved in 2005 as D209703 (2005).DOI: 10.1520/D2097-03R10.2Several methods of evaluating the resistance of an upholstery leather finish toflexing have been
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD209720032010STANDARDTESTMETHODFORFLEXTESTINGOFFINISHONUPHOLSTERYLEATHER 家具 皮革 表层 挠曲 测试 标准 试验 方法

链接地址:http://www.mydoc123.com/p-510987.html