ASTM D1874-1962(2010) Standard Specification for Water- or Solvent-Soluble Liquid Adhesives for Automatic Machine Sealing of Top Flaps of Fiberboard Shipping Cases《纤维板船运箱顶盖自动机密封用水可.pdf

《ASTM D1874-1962(2010) Standard Specification for Water- or Solvent-Soluble Liquid Adhesives for Automatic Machine Sealing of Top Flaps of Fiberboard Shipping Cases《纤维板船运箱顶盖自动机密封用水可.pdf》由会员分享，可在线阅读，更多相关《ASTM D1874-1962(2010) Standard Specification for Water- or Solvent-Soluble Liquid Adhesives for Automatic Machine Sealing of Top Flaps of Fiberboard Shipping Cases《纤维板船运箱顶盖自动机密封用水可.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D1874 62 (Reapproved 2010)Standard Specification forWater- or Solvent-Soluble Liquid Adhesives for AutomaticMachine Sealing of Top Flaps of Fiberboard ShippingCases1This standard is issued under the fixed designation D1874; the number immediately following the designation indicates the

2、year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers starch, dextrin, casein, r

3、esinbase, and other liquid adhesives (excepting pressure-sensitivetypes) used for sealing the top flaps of fiberboard shippingcases. It includes provisions for adhesive selection based on:(1) satisfactory machining characteristics on specific equip-ment, and (2) adequate adhesion under specified sto

4、rageconditions. This specification further provides for the controlof uniformity between lots of an adhesive selected on the abovebases by limiting variations in nonvolatile content and viscos-ity.1.2 This specification provides bases for adhesive selectionas well as product uniformity control. Test

5、 methods arespecified for measuring (1) nonvolatile content, (2) consis-tency, and (3) bonding permanency under specified storageconditions.1.3 The values stated in acceptable metric units are to beregarded as the standard. The values given in parentheses areprovided for information purposes only.2.

6、 Referenced Documents2.1 ASTM Standards:2D907 Terminology of AdhesivesD1084 Test Methods for Viscosity of AdhesivesD1489 Test Method for Nonvolatile Content of AqueousAdhesivesD1581 Test Method for Bonding Permanency of Water- orSolvent-Soluble Liquid Adhesives for Labeling GlassBottles3D1714 Test M

7、ethod fro WaterAbsorptiveness of FiberboardSpecimens for Adhesives33. Terminology3.1 Many terms in this specification are defined in Termi-nology D907.4. Physical Properties4.1 The general consistency shall be uniform, and theadhesive shall be free of lumps and particles.4.2 The machining properties

8、 shall be such that the adhesive(when diluted in accordance with to the manufacturers instruc-tions) shall not string when machine transfer surfaces areseparated, shall not build up excessively on machine parts, andshall not foam.4.3 The bonding permanency of the adhesive shall providea minimum of 7

9、5 % paper fiber tear when tested under theexposure conditions specified in the contract or purchase order.The exposure conditions shall be selected from those in Table 1of Test Method D1581.5. Permissible Variations5.1 The nonvolatile content of the adhesive shall be within61.5 % of that specified i

10、n the contract or purchase order.5.2 The consistency of the adhesive shall be within 620 %of that specified in the contract or purchase order.6. Sampling6.1 The adhesive sample shall be a 0.9-L (1-qt) aliquotconsisting of a composite taken when possible from three ormore separate containers chosen a

11、t random. Samples also shallbe taken from containers that appear to be nonrepresentativeand shall be tested separately. Before a sample is withdrawn,mix the contents in the container to uniform consistency. Placethe sample immediately in an airtight glass jar until tested.6.2 Samples of adhesives us

12、ed on fiberboard cases shall beof the same type used on the production line. Samples ofboards used for all bonding permanency tests shall be within adefined range of water absorptiveness to eliminate this variablefrom the test. The specific range shall be selected by the1This specification is under

13、the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.50 on Hot MeltPressure Sensitive Archive Adhesives.Current edition approved Oct. 1, 2010. Published October 2010. Originallyapproved in 1961. Last previous edition approved in 2004 as D1874 62 (20

14、04).DOI: 10.1520/D1874-62R10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved ve

15、rsion of this historical standard is referencedon www.astm.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.purchaser and shall be based upon the adhesive for shippingcases used on the production line.6.3 Test a minimum of six boa

16、rd or board-facing materialssamples in selecting the sample for each adhesion study. Rejectsamples that fail to fall within 650 % of the selected waterabsorptiveness values.6.4 Condition samples at 23 6 1C (73.4 6 1.8F) and 506 2 % relative humidity prior to each adhesion test to ensureuniformity.7.

17、 Test Methods7.1 Nonvolatile ContentTest Method D1489.7.2 ConsistencyMethod B (Brookfield viscometer) orMethod C (Stormer viscometer) of Test Methods D1084.7.3 Bonding PermanencyTest Method D1581.7.4 Water AbsorptivenessTest Method D1714.8. Number of Tests8.1 The number of test specimens shall be as

18、 specified ineach method of test designated in Section 7. The average resultfor the specimens tested shall conform to the requirementsprescribed in this specification.9. Retest and Rejection9.1 If the results of any test do not conform to the require-ments prescribed in this specification, at the op

19、tion of themanufacturer, that test shall be repeated on two additional setsof specimens from the same lot of adhesive, each of whichshall conform to the requirements specified. If either of thesetwo additional sets of specimens fails, the lot or batch ofmaterial may be rejected at the option of the

20、purchaser. Noticeof failure of material based on tests made in accordance withthis specification shall be reported to the manufacturer.10. Packaging and Marking10.1 PackagingThe material shall be packaged in stan-dard commercial containers, so constructed as to ensureacceptance by common or other ca

21、rrier for safe transportationat the lowest rate to the point of delivery, unless otherwisespecified in the contract or order.10.2 MarkingShipping containers shall be marked withthe following information:10.2.1 Manufacturers name, product code number, andbatch or lot number,10.2.2 Date of manufacture

22、 of product,10.2.3 Special handling instructions during product transfer,for example, “Ship in heated transfer,” and10.2.4 Special precautions required because of producttoxicity, flammability, or such information pertinent to theproper handling and storage of the product.11. Keywords11.1 adhesives;

23、 automatic machine sealing; solvent soluble;top flaps; water solubleASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any

24、 such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are in

25、vited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not receive

26、d a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of t

27、his standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D1874 62 (2010)2