ASTM D1519-1995(2014) Standard Test Methods for Rubber ChemicalsDetermination of Melting Range《橡胶化学品融化范围测定的标准试验方法》.pdf

《ASTM D1519-1995(2014) Standard Test Methods for Rubber ChemicalsDetermination of Melting Range《橡胶化学品融化范围测定的标准试验方法》.pdf》由会员分享，可在线阅读，更多相关《ASTM D1519-1995(2014) Standard Test Methods for Rubber ChemicalsDetermination of Melting Range《橡胶化学品融化范围测定的标准试验方法》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D1519 95 (Reapproved 2014)Standard Test Methods forRubber ChemicalsDetermination of Melting Range1This standard is issued under the fixed designation D1519; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of l

2、ast revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 These test methods cover the determination of themelting range of commercial rubber processing chemicalseither by use o

3、f capillary melting point tubes or by differentialscanning calorimetry (DSC).1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with it

4、s use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D4483 Practice for Evaluating Precision for Test MethodStandards in the

5、 Rubber and Carbon Black ManufacturingIndustriesE1 Specification for ASTM Liquid-in-Glass ThermometersE324 Test Method for Relative Initial and Final MeltingPoints and the Melting Range of Organic Chemicals(Discontinued 2001) (Withdrawn 2001)3E473 Terminology Relating to Thermal Analysis and Rhe-olo

6、gyE967 Test Method for Temperature Calibration of Differen-tial Scanning Calorimeters and Differential Thermal Ana-lyzers3. Terminology3.1 Definitions:3.1.1 differential scanning calorimetrysee TerminologyE473.4. Significance and Use4.1 This test method may be used for research and devel-opment. It

7、also may be used for quality assurance, provided astandard has been agreed upon between a producer and a user.4.2 For identification purposes, melting range should besupplemented by measurements of a more specific physical andchemical property.4.3 This test method is not recommended for rubber chemi

8、-cals that decompose at their melting ranges.4.4 The melting range as determined by Test MethodACapillary Tube Melting Range is not recommended as acriterion of purity of a rubber chemical.5. Sampling5.1 Grind a representative sample of the chemical to betested with a mortar and pestle, if necessary

9、, to pass completelythrough a 150-m (No. 100) sieve. Use the sample withoutfurther treatment.TEST METHOD ACAPILLARY TUBE MELTINGRANGE6. Apparatus6.1 Melting ApparatusAny electric melting apparatus thatsatisfies the requirements of Test Method E324 may be used orany suitable manually heated oil bath

10、such as Hershberg tube.6.2 Capillary TubeThe capillary tube to contain thesample shall be a glass tube approximately 150 mm long and1.2 to 1.4 mm in internal diameter with walls 0.2 to 0.3 mmthick and closed at one end.6.3 ThermometerThe thermometer shall be of the partialimmersion type and of suita

11、ble range selected from Specifica-tion E1, or of an equivalent range as specified by the ChemicalManufacturers Association. It shall be divided into subdivi-sions of 0.5C (1F) or less. Corrections for the thermometershall be determined by calibration against a thermometercertified by National Instit

12、ute of Standards and Technology.6.4 SieveA150-m (No. 100) sieve for screening thesample shall be provided.1These test methods are under the jurisdiction of ASTM Committee D11 onRubber and is the direct responsibility of Subcommittee D11.11 on ChemicalAnalysis.Current edition approved Aug. 1, 2014. P

13、ublished November 2014. Originallyapproved in 1995. Last previous edition approved in 2009 as D1519 95 (2009)1.DOI: 10.1520/D1519-95R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume in

14、formation, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States17. Procedure7.1 Select the

15、thermometer of the proper range and supportit so that it is immersed to the immersion mark in the liquid ofthe bath.7.2 Charge the capillary glass tube with sufficient powder toform a column in the bottom of the tube about 3 to 6-mm highwhen packed down as closely as possible by moderate tappingon a

16、 solid surface.7.3 Heat the bath until a temperature approximately 25Cbelow the expected melting range is reached. Then regulate therate of rise so that it averages about 3C/min for the rest of thedetermination except that the rate of rise is 1 6 0.2C/minduring the actual melting of the sample. When

17、 the temperaturehas risen to about 10C below the expected melting range,insert the capillary in the bath and adjust the height of the tubeso that the material in the capillary is beside the center of thethermometer bulb. The capillary tube is not placed in the bathpreviously, since many materials un

18、dergo decomposition uponprolonged heating. Major adjustments of the heat sourceshould be avoided during the actual melting range.7.4 Record the melting range as the temperature rangebetween which liquefaction first becomes evident and thetemperature at which no further visual change is observed inth

19、e mass.NOTE 1The initial melting temperature is the temperature at which thefirst actual formation of liquid occurs, either as a minute drop or as a film.It is not a preliminary contraction, sintering, or darkening. It occurs wellbefore the formation of meniscus. The liquefaction may occur at the to

20、p,bottom, or sides of the sample in the capillary, as well as the rear. Whenthe latter occurs, the point may be missed, unless care is taken to watch therear of the tube; a mirror is a convenient aid for this purpose.NOTE 2The final melting temperature is the temperature at which nofurther liquefact

21、ion is observed.8. Report8.1 Report the results to the nearest division on thethermometer, after applying necessary calibration corrections.9. Precision and Bias49.1 This precision and bias section has been prepared inaccordance with Practice D4483. Refer to this practice forterminology and other st

22、atistical details.9.2 The results in this precision and bias section give anestimate of the precision of the test method with the materialsused in the particular interlaboratory program as described in9.3. The precision parameters should not be used foracceptance/rejection testing of any group of ma

23、terials withoutdocumentation that they are applicable to those particularmaterials and the specific testing protocols that include this testmethod.9.3 A Type 1 interlaboratory precision program was con-ducted. Repeatability is short term and reproducibility is shortterm. Seven laboratories participa

24、ted and three materials wereused.Atest result is the value obtained from one determination.Two determinations were run on each material, and thisprotocol was repeated on each of three days. The analysis forprecision followed the general procedure as set forth in Annex5 of Practice D4483. Each cell o

25、f Practice D4483 Table 1 basicdata format contained six values (three test days, two testresults each day). The estimates for the repeatability param-eters therefore contain two undifferentiated sources ofvariation, that is, replicates within days and between days. Thefinal precision parameters are

26、given in Table 1 of this testmethod.9.4 The results of the precision calculations for the initialmelting point and the final melting point are arranged inascending “mean level” order, and given in Table 1.9.5 RepeatabilityThe pooled repeatability, r, of this testmethod has been established as 1.58C,

27、 as given in Table 1.Two single test results obtained under normal test methodprocedures that differ by more than 1.58C must be consideredas suspect, that is, having been derived from different ornonidentical sample populations. If this is the case, appropriatecorrective action should be taken.9.6 R

28、eproducibilityThe pooled reproducibility, R, of thistest method has been established as 3.40C, as given in Table1. Two single test results obtained under normal test methodprocedures that differ by more than 3.40C must be consideredas suspect, that is, having been derived from different ornonidentic

29、al sample populations. If this is the case, appropriatecorrective action should be taken.9.7 BiasIn test method terminology, bias is the differencebetween an average test value and the reference (or true) testproperty value. Reference values do not exist for this testmethod since the value of the me

30、lting point is exclusivelydefined by the test method. Bias, therefore, cannot be deter-mined.4Supporting data have been filed at ASTM International Headquarters and maybe obtained by requesting Research Report RR:D11-1070.TABLE 1 ASTM Test Method PrecisionType 1: Test MethodD1519 Capillary Melting R

31、angeNOTE 1This is short-term precision (days).NOTE 2These are the same chemicals used for the DSC.MaterialMeanLevel,CWithin LaboratoriesABetween LaboratoriesASr r (r) SR R (R)Initial A 47.3 0.681 1.91 4.02 1.07 3.00 6.34Initial B 98.8 0.491 1.38 1.39 1.26 3.52 3.57Initial C 176.4 0.671 1.88 1.07 1.2

32、5 3.49 1.98Final A 49.4 0.376 1.05 2.13 0.55 1.53 3.10Final B 101.4 0.426 1.19 1.18 1.43 3.99 3.94Final C 179.7 0.663 1.86 1.03 1.50 4.19 2.33Pooled 0.565 1.58 1.80 1.22 3.40 3.54ASr = within laboratory, standard deviation.r = repeatability in measurement units.(r) = repeatability (in percent).SR =

33、between laboratory, standard deviation.R = reproducibility in measurement units.(R) = reproducibility (in percent).D1519 95 (2014)2TEST METHOD BDIFFERENTIAL SCANNINGCALORIMETRY10. Apparatus10.1 Differential Scanning Calorimeter, capable of heating atest specimen and a reference material at a control

34、led rate andof automatically recording the differential heat flow betweenthe samples and the reference material to the required sensi-tivity and precision.10.2 Specimen Pans, composed of aluminum or other metalof high thermal conductivity. The specimen pans must not reactwith the sample and must not

35、 melt under the temperatures ofthe test.10.3 Nitrogen, or other inert purge gas supply.10.4 Analytical Balance, with a capacity greater than 20 mg,capable of weighing to the nearest 0.01 mg.11. Calibration11.1 Using the same heating rate, purge gas, and flow rate tobe used for the specimen, calibrat

36、e the temperature axis of theinstrument using the procedure in Test Method E967.12. Procedure12.1 Weigh about 10 to 20 mg of the sieved specimen intoa DSC specimen pan. Cover and seal the specimen pan andplace into the DSC sample holder.12.2 Place an empty sealed pan into the reference sampleholder.

37、12.3 Close the sample chamber and ensure that the purgegas flow matches that used for the calibration.12.4 Heat the specimen rapidly to 50C below the meltingtemperature and allow to equilibrate.12.5 Heat the specimen through the endotherm until base-line is re-established above the melting endotherm

38、. Heatingrate must be the same as that used for the calibration of theinstrument. Ten degrees Celsius is a commonly used rate.Record the accompanying thermal curve.12.6 Reweigh the specimen after completion of scanning,and discard. Report any mass loss observed.NOTE 3Mass loss is only one indication

39、 of suspected sampledegradation or decomposition. Other decomposition indicators, such ascolor change, may be noted if the specimen pan is opened.12.7 From the resultant curve, measure the temperatures forthe desired points on the curve, Te, Tp(see Fig. 1) to therequired precision,where:Te= extrapol

40、ated onset temperature for fusion, C, andTp= melting peak temperature, C.13. Report13.1 Report Teand Tp, as well as heating rate used.13.2 Any side reaction (for example, thermal degradation oroxidation) also should be reported and the reaction identified,if possible.14. Precision and Bias414.1 This

41、 precision and bias section has been prepared inaccordance with Practice D4483. Refer to this practice forterminology and other statistical details.14.2 The results in this precision and bias section give anestimate of the precision of the test method with the materialsused in the particular interla

42、boratory program as described in14.3. The precision parameters should not be used foracceptance/rejection testing of any group of materials withoutFIG. 1 Sample Melting EndothermD1519 95 (2014)3documentation that they are applicable to those particularmaterials and the specific testing protocols tha

43、t include this testmethod.14.3 A Type 1 interlaboratory precision program was con-ducted. Repeatability is short term and reproducibility is shortterm. Eleven laboratories participated and three materials wereused.Atest result is the value obtained from one determination.Two determinations were run

44、on each material, and thisprotocol was repeated on each of three days. The analysis forprecision followed the general procedure as set forth in Annex5 of Practice D4483. Each cell of Practice D4483 Table 1 basicdata format contained six values (three test days, two testresults each day). The estimat

45、es for the repeatability param-eters therefore contain two undifferentiated sources ofvariation, that is, replicates within days and between days. Thefinal precision parameters are given in Table 2 of this testmethod.14.4 The results of the precision calculations for the onsetand the peak are arrang

46、ed in ascending “mean level” order, andgiven in Table 2.14.5 RepeatabilityThe pooled repeatability, r, of this testmethod has been established as 1.40C, as given in Table 2.Two single test results obtained under normal test methodprocedures that differ by more than 1.40C must be consideredas suspect

47、, that is, having been derived from different ornonidentical sample populations. If this is the case, appropriatecorrective action should be taken.14.6 ReproducibilityThe pooled reproducibility, R, of thistest method has been established as 3.75C, as given in Table2. Two single test results obtained

48、 under normal test methodprocedures that differ by more than 3.75C must be consideredas suspect, that is, having been derived from different ornonidentical sample populations. If this is the case, appropriatecorrective action should be taken.14.7 BiasIn test method terminology, bias is the differenc

49、ebetween an average test value and the reference (or true) testproperty value. Reference values do not exist for this testmethod since the value of the melting point is exclusivelydefined by the test method. Bias, therefore, cannot be deter-mined.15. Keywords15.1 capillary; differential scanning calorimetry (DSC);melting range; rubber chemicalsASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that det