ASTM D1201-2013 Standard Specification for Thermosetting Polyester Molding Compounds《热固聚酯模制化合物的标准规格》.pdf

《ASTM D1201-2013 Standard Specification for Thermosetting Polyester Molding Compounds《热固聚酯模制化合物的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM D1201-2013 Standard Specification for Thermosetting Polyester Molding Compounds《热固聚酯模制化合物的标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D1201 13Standard Specification forThermosetting Polyester Molding Compounds1This standard is issued under the fixed designation D1201; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number

2、 in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers compression molding,thermosetting, unsaturated polyester molding compounds asfurther defined in 3.1.1.2 The values

3、 stated in SI units are to be regarded as thestandard.NOTE 1The properties included in this specification are those requiredto identify the types of molding compounds covered. There may be otherrequirements necessary to identify particular characteristics. These will beadded to the specification as

4、their inclusion becomes generally desirableand the necessary test data and methods become available.NOTE 2ISO 36721: 1979(E) is similar but not equivalent to thisspecification. Product classification and characterization are not equiva-lent.2. Referenced Documents2.1 ASTM Standards:2D256 Test Method

5、s for Determining the Izod PendulumImpact Resistance of PlasticsD495 Test Method for High-Voltage, Low-Current, Dry ArcResistance of Solid Electrical Insulation (Withdrawn2013)3D570 Test Method for Water Absorption of PlasticsD618 Practice for Conditioning Plastics for TestingD790 Test Methods for F

6、lexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD792 Test Methods for Density and Specific Gravity (Rela-tive Density) of Plastics by DisplacementD3892 Practice for Packaging/Packing of Plastics2.2 ISO Standard:ISO 36721: 1979(E) PlasticsUnsaturated Poly

7、esterResinsPart 1: Designation43. Classification3.1 This specification covers the following types of polyes-ter molding compounds:3.1.1 Type 1General-purpose, granular material with min-eral fillers.3.1.2 Type 2General-purpose, granular material with min-eral and cellulosic fillers, and having impro

8、ved mechanicalstrength.3.1.3 Type 3General-purpose, putty-type material withmineral fillers.3.1.4 Type 4Putty-type material with mineral fillers hav-ing superior electrical properties.3.1.5 Type 5High-impact, glass-fiber filled material in matform having good electrical properties.3.1.6 Type 6High-i

9、mpact, glass-fiber filled material inputty form.4. General Requirements4.1 The molding compounds shall be of uniformcomposition, so compounded as to conform to the require-ments prescribed in this specification.4.2 The apparent density, bulk factor, particle size, physicalform, and color of the comp

10、ound shall be as agreed uponbetween the purchaser and supplier.NOTE 3The terms “apparent density,” “bulk factor,” and “particlesize” cannot be used in the same sense with putty-type and glass-filledmaterials as with granular materials.5. Detail Requirements5.1 Test specimens, molded by compression u

11、nder condi-tions specified by the manufacturer, shall conform to therequirements prescribed in Table 1.6. Sampling6.1 Abatch of molding compound shall be considered a unitof manufacture and may consist of a blend of two or moreproduction runs of the same material.1This specification is under the jur

12、isdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.16 on ThermosettingMaterials.Current edition approved Sept. 1, 2013. Published September 2013. Originallyapproved in 1952. Last previous edition approved in 2012 as D1201 - 99(2012).DOI: 10.1520/D1201-13.

13、2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is ref

14、erenced onwww.astm.org.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken,

15、PA 19428-2959. United States16.2 Adequate statistical sampling shall be used.7. Test Methods7.1 The properties enumerated in this specification shall bedetermined in accordance with the following methods:7.1.1 ConditioningMolded specimens shall be condi-tioned in accordance with Procedure B of Pract

16、ice D618,except for the tests for arc resistance where Procedure A shallbe used.7.1.2 Test ConditionsTests shall be conducted in thestandard laboratory atmosphere of 23 6 2C and 50 6 10 %relative humidity, unless otherwise specified in the test meth-ods or in this specification.7.1.3 Specific Gravit

17、yMethod A of Test Methods D792.7.1.4 Flexural StrengthTest Methods D790, Procedure A.7.1.5 Modulus of Elasticity in FlexureTest Methods D790,Procedure A.7.1.6 Impact Resistance (Izod)Method A of Test MethodsD256. Test specimens shall be 12.7 by 12.7 by 63.5 mm.NOTE 4Impact strength specimens may be

18、cut from compression-molded 12.7 by 12.7-mm bars having lengths greater than 63.5 mm.7.1.7 Arc ResistanceTest Method D495.7.1.8 Water AbsorptionTest Method D570, using the 24-himmersion procedure.8. Number of Tests8.1 One set of test specimens as prescribed in Section 7shall be considered sufficient

19、 for testing each batch. Theaverage result for the specimens tested shall conform to therequirements prescribed in this specification. All of the testslisted in Section 7 shall be used to establish conformity of amaterial to this specification. It is recommended that routineinspection be limited to

20、those tests required to identify thematerial to the satisfaction of the purchaser. The purchasershall state in the contract or order the tests which themanufacturer will be required to make on each shipment foridentification of the material.9. Rejection and Rehearing9.1 Compounds that fail to confor

21、m to the requirements ofthis specification may be rejected. Rejection should be reportedto the producer or supplier promptly and in writing. In case ofdissatisfaction with the results of the test, the producer orsupplier may make claim for a rehearing.10. Packaging and Package Marking10.1 PackagingT

22、he compound shall be packaged in stan-dard commercial containers, so constructed as to ensureacceptance by common or other carriers for safe transportationat the lowest rate to the point of delivery, unless otherwisespecified in the contract or order.10.2 Package MarkingShipping containers shall bem

23、arked with the name of the compound, type, color, and thequantity contained therein as defined by the contract or orderunder which shipment is made, the name of the manufacturer,and the number of the contract or order.10.3 All packing, packaging, and marking provisions ofPractice D3892 shall apply t

24、o this specification.11. Keywords11.1 molding compounds (thermosetting); polyester; un-saturated polyesterTABLE 1 Detail Requirements for Compression-Molded Test SpecimensType 1 Type 2 Type 3 Type 4 Type 5 Type 6Specific gravity, 23/23C:min 2.18 1.6 1.7 1.9 1.95 1.75max 2.28 1.9 1.9 2.1 2.10 1.90Fle

25、xural strength, min:MPa 51.7 65.5 51.7 51.7 82.7 82.7Modulus of elasticity in flexure, min:MPa 13 800 8 960 8 960 12 400 13 800 11 000Impact resistance (Izod), min, J/m of notch . . . . 320(6) 320(6)Arc resistance, min, s 175 125 125 175 130 75Water absorption, 24 h, max, % 0.15 1.0 0.5 0.15 0.15 0.

26、25D1201 132SUMMARY OF CHANGESCommittee D20 has identified the location of selected changes to this standard since the last issue,D1201 - 99(2012), that may impact the use of this standard. (September 1, 2013)(1) Modified the conditioning statement in 7.1.2 to reflectcurrent specifications found in P

27、ractice D618.(2) Reworded 3.1.5 for clarification.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent right

28、s, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for r

29、evision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing y

30、ou shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D1201 133