ASTM C980-2013a Standard Specification for Industrial Chimney Lining Brick《工业烟囱衬壁的标准规格》.pdf

《ASTM C980-2013a Standard Specification for Industrial Chimney Lining Brick《工业烟囱衬壁的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM C980-2013a Standard Specification for Industrial Chimney Lining Brick《工业烟囱衬壁的标准规格》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C980 13C980 13aStandard Specification forIndustrial Chimney Lining Brick1This standard is issued under the fixed designation C980; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in

2、parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers solid kiln fired brick made from clay, shale, or mixtures thereof suitable for use in masonryconstruction in contact w

3、ith the chemicals present in flue gases found in industrial chimneys. These brick are normally used withchemical-resistant mortars.1.2 The physical and chemical properties of chimney lining brick differ from supplier to supplier mainly because theircomposition is determined by the source of raw mate

4、rials. Chimney lining brick, regardless of these differences, are consideredto be of three types noted as follows:1.2.1 Type IFor use where low absorption and high acid resistance are not major factors.1.2.2 Type IIFor use where lower absorption and higher acid resistance are required.1.2.3 Type III

5、For use where lowest absorption and highest acid resistance are required.NOTE 1Types I, II, and III may not differ significantly in their resistance to thermal shock, and selection of brick type should be based upon theirabsorption and acid-resistant service requirements.1.2 Terminology related to i

6、ndustrial floor brick is found in Terminology C1232.1.3 UnitsThe values stated in inch-pound units are to be regarded as standard. The values given in parentheses aremathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not

7、 purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2

8、C20 Test Methods for Apparent Porosity, Water Absorption, Apparent Specific Gravity, and Bulk Density of Burned RefractoryBrick and Shapes by Boiling WaterC67 Test Methods for Sampling and Testing Brick and Structural Clay TileC1232 Terminology of MasonryE11 Specification for Woven Wire Test Sieve C

9、loth and Test SievesC1232 Terminology of Masonry3. Terminology3.1 DefinitionsFor definitions relating to industrial chimney lining brick, refer to Terminology C1232.4. Classification4.1 The physical and chemical properties of chimney lining brick differ from supplier to supplier mainly because their

10、composition is determined by the source of raw materials. Chimney lining brick, regardless of these differences, are consideredto be of three types noted as follows:4.1.1 Type IFor use where low absorption and high acid resistance are not major factors.4.1.2 Type IIFor use where lower absorption and

11、 higher acid resistance are required.1 This specification is under the jurisdiction of ASTM Committee C15 on Manufactured Masonry Units and is the direct responsibility of Subcommittee C15.02 on Brickand Structural Clay Tile.Current edition approved June 1, 2013Dec. 15, 2013. Published June 2013Janu

12、ary 2014. Originally approved in 1982. Last previous edition approved in 20102013 asC980 10.C980 13. DOI: 10.1520/C0980-13.10.1520/C0980-13A.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolum

13、e information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequa

14、tely depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM In

15、ternational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.1.3 Type IIIFor use where lowest absorption and highest acid resistance are required.NOTE 1Types I, II, and III may not differ significantly in their resistance to thermal shock, and selection of brick

16、 type should be based upon theirabsorption and acid-resistant service requirements.5. Sulfuric Acid Boil Test5.1 When tested in accordance with Section 79, the brick shall conform to the requirements for “Maximum Average WeightLoss by H2SO4 Boil Test” as shown in Table 1.6. Physical Properties6.1 Co

17、mpressive StrengthWhen tested in accordance with Test Methods C67, Section 6 (Compressive Strength), the brickshall conform to the requirements for “Minimum Compressive Strength” as shown in Table 1.6.2 Water AbsorptionWhen tested in accordance with Test Methods C20, Section 10 (Water Absorption), t

18、he brick shallconform to the requirements for “Maximum Water Absorption by 2-h Boiling” as shown in Table 1.5.3 SizesThe sizes of brick shall be as specified by the purchaser. When tested in accordance with Test Methods C67, Section11 (Measurement of Size), the brick shall conform to the requirement

19、s for “Permissible Variations in Dimensions” as shown inTable 2.5.4 WarpageWhen tested in accordance with Test Methods C67, Section 12 (Measurement of Warpage), the tolerance onwarpage of the brick shall be as indicated in Table 2.5.5 TextureScoring or matte texturing, or both, of the brick is recom

20、mended. However, no flutes or scores shall exceed 18 in.(3.0 mm) in height of protrusion or in depth.7. Dimensions, Mass, and Permissible Variations7.1 SizesThe sizes of brick shall be as specified by the purchaser. When tested in accordance with Test Methods C67, Section11 (Measurement of Size), th

21、e brick shall conform to the requirements for “Permissible Variations in Dimensions” as shown inTable 2.7.2 WarpageWhen tested in accordance with Test Methods C67, Section 12 (Measurement of Warpage), the tolerance onwarpage of the brick shall be as indicated in Table 2.8. Black Heart Finish and App

22、earance8.1 Black HeartBrick when broken may have a dark area that has a steely appearance and is sharply delineated from thesurrounding normal color of the brick it is known as black heart or black core. Black heart is generally the result of the reductionof iron minerals during the firing process.

23、Its presence, regardless of size in brick that otherwise meet the physical and chemicalrequirements of this specification, shall not be cause for rejection.8.2 TextureScoring or matte texturing, or both, of the brick is recommended. However, no flutes or scores shall exceed 18 in.(3.0 mm) in height

24、of protrusion or in depth.9. Test for Solubility in Sulfuric Acid9.1 Significance and UseThis test with sulphuric acid represents an extremely severe one and may not be significant forchemical-resistant brick in less demanding applications. It can be assumed that sulphuric acid in this test concentr

25、ation will be morecorrosive than most other acids excluding those containing flourine. A similar test procedure using other chemicals may be moresuitable for specific purposes. The performance of these other tests and appropriate qualifying data should be resolved betweenthe purchaser and the seller

26、.9.2 Apparatus:9.2.1 Crusher, jaw-type.9.2.2 Sieves, 14-in. (6.3-mm) and No. 4 (4.75-mm), (equivalent to 3-mesh and 4-mesh sieves, respectively, in the Tyler series),conforming to Specification E11.TABLE 1 Physical Properties and Chemical RequirementsADesignation Minimum Compressive Strength, Gross

27、Area, psi (MPa)Maximum Water Absorption by 2-hBoiling, %Maximum AverageWeight Loss byH2SO4 Boil Test, %Average of 10 Individual Average of 10 IndividualType I 8 500 (58.6) 8 000 (55.2) 6.0 7.0 20Type II 10 000 (69.0) 9 000 (62.2) 4.0 5.0 12Type III 12 000 (82.8) 10 000 (69.0) 1.0 1.5 8A One complete

28、 set of tests for each of the above requirements shall be performed from brick randomly selected from every 100 000 bricks.C980 13a29.2.3 Mechanical Shaking Device, producing a lateral and vertical motion of the sieve, accompanied by a jarring action so asto keep the sample moving continuously over

29、the surface of the sieve.9.2.4 Drying Oven.9.2.5 Analytical Balance and Weights, 0.01-g sensitivity.9.2.6 Desiccator.9.2.7 Erlenmeyer Flask, 750-mL, of heat-resistant and chemically resistant glass.9.2.8 Water-Cooled Condenser.9.2.9 Hot Plate.9.2.10 Fritted-Glass Funnel, fine porosity.9.2.11 Suction

30、 Pump.9.3 Preparation of SamplePrepare the sample from at least five masonry units selected in accordance with Test Methods C67.Remove the skin surface from a quarter of each unit selected, and crush the remaining pieces in a jaw-type crusher, with the jawsset so that the grain size of the product r

31、anges from material retained on a 14-in. (6.3-mm) sieve to material passing a No. 4(4.75-mm) sieve. Reduce this material either by mixing and quartering or by a mechanical splitter to approximately a 1000-gsample, and screen in a mechanical shaking device for 15 min, using the No. 3 and No. 4 sieves

32、. Thoroughly mix the portion ofthe material passing the No. 3 sieve and remaining on the No. 4 sieves (Note 2), and then quarter down to obtain two 50-g samples.Dry these samples in a drying oven at 240F (120C) for at least 16 h, and then cool in a desiccator.NOTE 2Although it is recognized that som

33、e types of material tend to break down in a manner yielding various-shaped particles, no attempt shall bemade at hand selection.9.4 ProcedureTransfer each of the 50-g samples, weighed to the nearest 0.01 g, and 250 mL of sulfuric acid (sp gr 1.706) or60 Baum (78 weight %) into separate 750-mL Erlenm

34、eyer flasks. Insert water-cooled condensers and boil on hot plates for 48h (Note 3). Cool the flasks and contents sufficiently to permit handling, and decant the solutions through fritted-glass funnels withthe aid of suction, retaining the samples in the flasks. Add about 250 mL of water to the flas

35、ks, boil for 10 min, and decant withthe aid of suction through the same funnels as used previously. Repeat this washing procedure three times. On the fourthdecantation of wash water, transfer the samples to the funnels, using hot water to aid in the transfer. Dry the funnels and contentsin the oven

36、at 240F (120C) for at least 16 h, and cool in a desiccator. Remove material from the funnels, brushing out the finesif necessary, and weigh to the nearest 0.01 g.NOTE 3Regulate the temperature of the hot plate so as to maintain a gentle boiling solution, avoiding any considerable agitation of the sa

37、mple. Theuse of a variable transformer in series with the hot plate is suggested.9.5 Calculations and ReportCalculate the loss in weight as a percentage of the original weight. Make duplicatedeterminations, and report an average of the two results to the nearest 0.1 %.9.6 Precision and BiasA stateme

38、nt on precision and bias will be added at a later date.10. Sampling and Testing10.1 The brick shall be sampled and tested in accordance with applicable sections in Test Methods C67 and Sections 5 and 8.10.2 The manufacturer or the seller shall furnish specimens for test. The place or places of selec

39、tion shall be designated whenthe purchase order is placed.11. Keywords11.1 absorption; acid resistance; acid solubility; ceramic; industrial chimney; masonry; physical properties; solid brickTABLE 2 Permissible Variations in Dimensions and WarpageADimensionsDimensionsMaximumPermissibleVariations inD

40、imensionsBetween Largestand Smallest Brickin a RandomSampling of 10Brick, %WarpageMaximum Face andDiagonal Dimensions,in. (mm)MaximumPermissibleDeviation,In. (mm)HeightLengthWidth355up to 9 12 (241) incl.18 (3.0).AOne complete set of tests for each of the above requirements shall be performedfrom br

41、ick randomly selected from every 100 000 bricks.C980 13a3SUMMARY OF CHANGESCommittee C15 has identified the location of selected changes to this standard since the last issue (C980 13)that may impact the use of this standard. (December 15, 2013)(1) Select sections within the standard were reorganize

42、d using the ASTM Form and Style Standards manual as a guideline.SUMMARY OF CHANGESCommittee C15 has identified the location of selected changes to this standard since the last issue (C980 10)that may impact the use of this standard. (June 1, 2013)(1) A new Section 3, Terminology, was added and subse

43、quent sections renumbered.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infrin

44、gement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision of this standard

45、or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views

46、known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C980 13a4