ASTM C963-2000(2007) Standard Specification for Packaging Identification Shipment and Storage of Lock-Strip Gaskets《锁条衬垫的包装、识别、交货及储存标准规范》.pdf

《ASTM C963-2000(2007) Standard Specification for Packaging Identification Shipment and Storage of Lock-Strip Gaskets《锁条衬垫的包装、识别、交货及储存标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM C963-2000(2007) Standard Specification for Packaging Identification Shipment and Storage of Lock-Strip Gaskets《锁条衬垫的包装、识别、交货及储存标准规范》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C 963 00 (Reapproved 2007)Standard Specification forPackaging, Identification, Shipment, and Storage of Lock-Strip Gaskets1This standard is issued under the fixed designation C 963; the number immediately following the designation indicates the year oforiginal adoption or, in the case o

2、f revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the packaging, identification,shipment, and storage of lock-strip g

3、askets and componentsthat comply with Specification C 542 and that are used inbuilding walls that are not more than 15 from a vertical plane.2. Referenced Documents2.1 ASTM Standards:2C 542 Specification for Lock-Strip GasketsC 716 Specification for Installing Lock-Strip Gaskets andInfill Glazing Ma

4、terialsC 717 Terminology of Building Seals and SealantsC 964 Guide for Lock-Strip Gasket Glazing3. Significance and Use3.1 This specification can be referred to in contract docu-ments as a method and workmanship standard. See also relatedSpecification C 542, Specification C 716, Terminology C 717,an

5、d Guide C 964.4. Packaging, Identification, Shipment, and Storage4.1 PackagingGaskets, gasket assemblies, and compo-nents shall be properly packaged to avoid cutting, abrading,permanently distorting, or otherwise damaging them duringshipping and storage. Each container shall be legibly andindelibly

6、marked with the manufacturers name and address,the project name, the part or assembly number for the gaskets,the quantity of parts in each container, and other identificationrequired by the purchaser.4.2 Identification and MarkingEach gasket, gasket as-sembly, or component shall be clearly and legib

7、ly labeled withthe manufacturers identifying part number and other identifi-cation required by the purchaser.4.3 ShipmentGaskets, gasket assemblies, and componentsshall be shipped in closed containers using the best commercialpractices as defined by the Interstate Commerce CommissionManual,“ Uniform

8、 Freight Classification Number 9.”3Contain-ers shall not be handled in a manner that will cause damage tothe contents.4.4 StorageGaskets, gasket assemblies, and components,shall be stored in original containers in a clean dry area, free ofdust, debris, oils, solvents, welding slag, spatter, or spark

9、s, orother materials and conditions that may cause damage to thecontainers and the contents.5. Comparison to Other Standards5.1 The Committee with jurisdiction over this standard1isnot aware of any comparable standards published by otherorganizations.6. Keywords6.1 gasket; glazing; lock-strip1This s

10、pecification is under the jurisdiction of ASTM Committee C24 onBuilding Seals and Sealants and is the direct responsibility of Subcommittee C24.73on Compression Seal and Lock Strip Gaskets.Current edition approved June 1, 2007. Published July 2007. Originally approvedin 1981. Last previous edition a

11、pproved in 2000 as C 963 00.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Published by the Uniform Classif

12、ication Committee, 202 Union Station, 516 W.Jackson Blvd., Chicago, IL 60606.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.ASTM International takes no position respecting the validity of any patent rights asserted in connection wit

13、h any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible techn

14、ical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful considerati

15、on at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Har

16、bor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).C 963 00 (2007)2