ASTM C899-1979(2013) Standard Practice for Use of Metric Units of Measure for Reporting Properties of Refractory Materials《耐火材料特性报告用公制测量单位的标准实施规程》.pdf

《ASTM C899-1979(2013) Standard Practice for Use of Metric Units of Measure for Reporting Properties of Refractory Materials《耐火材料特性报告用公制测量单位的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM C899-1979(2013) Standard Practice for Use of Metric Units of Measure for Reporting Properties of Refractory Materials《耐火材料特性报告用公制测量单位的标准实施规程》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C899 79 (Reapproved 2013)Standard Practice forUse of Metric Units of Measure for Reporting Properties ofRefractory Materials1(COMMITTEE C-8 SUPPLEMENT TO E 380)This standard is issued under the fixed designation C899; the number immediately following the designation indicates the year o

2、foriginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice presents the units to be employed forreporti

3、ng the properties of refractories, such as density, crush-ing stress, modulus of rupture, tensile stress, thermalconductivity, and permeability.1.2 For convenience, a table of conversion factors betweeninch-pound units and SI units is included.2. Referenced Documents2.1 ASTM Standards:2E380 Practice

4、 for Use of the International System of Units(SI) (the Modernized Metric System) (Withdrawn 1997)32.2 ISO Standard:ISO 1000 SI Units and Recommendations for the Use ofTheir Multiples and of Certain Other Units43. Significance and Use3.1 This practice is provided to facilitate comparison ofphysical a

5、nd mechanical properties of refractory materials byestablishing uniform presentation of data.3.2 Units have been chosen, where possible, to result innumbers of magnitude familiar in the refractories industry, thatis, g/cm3rather than the SI preferred unit kg/m3.Itisrecommended that SI prefixes be se

6、lected for use with the unitssuch that the resulting numerical values lie between 0.1 and1000. For most properties, the prefixes kilo (k) and mega (M)are preferred. Other prefixes are given in the following table:MultiplicationFactor Prefix Symbol109106gigamegaGM103102kilohectoAkh101101dekaAdeciAdad

7、102103centiAmillicm106109micronanonATo be avoided where practical.3.3 The conversion factors, which have been selected fortheir general utility in the refractories industry, have been takenfrom Standard E380, where possible. For uniformity, they havebeen presented to four decimal places. In use, the

8、 convertedvalues should be rounded to the same number of significantfigures as in the original value.4. Standard Units4.1 Densitygrams per cubic centimetre (g/cm3).4.2 Energy or work joules (J) or megajoules (MJ).4.3 Massgrams (g), kilograms (kg), or megagrams (Mg).4.4 Permeability is currently expr

9、essed in darcys. One darcyis a flow of 1.00 cm3/s of a fluid of 1 centipoise (cP) viscositythrough a 1-cm cube of the material being measured under apressure differential of 1 atmosphere. Thus, a darcy is not an SIunit. No permeability units are given in E380. Until an SI unitof permeability is adop

10、ted, express permeability in darcys.4.5 Powerwatts (W) or kilowatts (kW).4.6 Pressure or stressmegapascals (MPa) (preferred). Forstress less than 1 MPa, kilopascals (kPa) may be used.NOTE 1Included are bending, crushing, shear, and tensile stress,modulus of rupture, and elastic modulus.4.7 Thermal c

11、onductivitywatts per metre kelvin (W/mK).4.8 Thermal expansion coeffcient change in length perunit length per kelvin.1This practice is under the jurisdiction ofASTM Committee C08 on Refractoriesand is the direct responsibility of Subcommittee C08.92 , the The Joseph E.Kopanda Subcommittee for Editor

12、ial, Terminology and Classification.Current edition approved Sept. 1, 2013. Published September 2013. Originallyapproved in 1979. Last previous edition approved in 2007 as C899 79 (2007).DOI: 10.1520/C0899-79R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Cus

13、tomer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American National Standards Institute (ANSI), 25

14、W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15. Conversion Factors5.1 Converson FactorsSee Table 1.6. Keywords6.1 metric; practice; properties; refractoryASTM Internatio

15、nal takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their

16、 own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be

17、 addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards

18、, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Conversion FactorsC899 79 (2013)2