ASTM C88 C88M-2018 Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate.pdf
《ASTM C88 C88M-2018 Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate.pdf》由会员分享,可在线阅读,更多相关《ASTM C88 C88M-2018 Standard Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: C88 13C88/C88M 18Standard Test Method forSoundness of Aggregates by Use of Sodium Sulfate orMagnesium Sulfate1This standard is issued under the fixed designation C88;C88/C88M; the number immediately following the designation indicates the yearof original adoption or, in the case of revi
2、sion, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope Scope*1.1 This te
3、st method covers the testing of aggregates to estimate their soundness when subjected to weathering action inconcrete or other applications. This is accomplished by repeated immersion in saturated solutions of sodium or magnesium sulfatefollowed by oven drying to partially or completely dehydrate th
4、e salt precipitated in permeable pore spaces. The internal expansiveforce, derived from the rehydration of the salt upon re-immersion, simulates the expansion of water on freezing. This test methodfurnishes information helpful in judging the soundness of aggregates when adequate information is not a
5、vailable from servicerecords of the material exposed to actual weathering conditions.1.2 The values stated in SI or inch pound units shall be regarded separately as standard. The inch pound units are shown inbrackets. The values stated are not exact equivalents; therefore each system shall be used i
6、ndependently of the other. Combiningvalues from the two systems may result in nonconformance.1.3 Some values have only SI units because the inch-pound equivalents are not used in practice.1.4 The values given in parentheses are provided for information purposes only.If the results obtained from anot
7、her standardare not reported in the same system of units as used by this test method, it is permitted to convert those results using the conversionfactors found in the SI Quick Reference Guide.2NOTE 1Sieve size is identified by its standard designation in Specification E11. The alternate designation
8、 given in parentheses is for information onlyand does not represent a different standard sieve size.1.5 This standard does not purport to address all of the safety problems concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appropriate safety
9、 safety, health, and healthenvironmental practices anddetermine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Developm
10、ent of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:3C33C33/C33M Specification for Concrete AggregatesC125 Terminology Relating to Concrete and Concrete AggregatesC136C1
11、36/C136M Test Method for Sieve Analysis of Fine and Coarse AggregatesC670 Practice for Preparing Precision and Bias Statements for Test Methods for Construction MaterialsC702C702/C702M Practice for Reducing Samples of Aggregate to Testing SizeD75D75/D75M Practice for Sampling AggregatesE11 Specifica
12、tion for Woven Wire Test Sieve Cloth and Test SievesE100 Specification for ASTM Hydrometers1 This test method is under the jurisdiction of ASTM Committee C09 on Concrete and Concrete Aggregates and is the direct responsibility of Subcommittee C09.20 onNormal Weight Aggregates.Current edition approve
13、d Aug. 1, 2013Aug. 1, 2018. Published August 2013August 2018. Originally approved in 1931. Last previous edition approved in 20052013 asC88 05.C88 13. DOI: 10.1520/C0088-13.10.1520/C0088_C0088M-18.2 Annex A in Form and Style for ASTM Standards, www.ASTM.org/COMMIT/Blue_Book.dpf3 For referencedASTM s
14、tandards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of a
15、n ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as publi
16、shed by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1E323 Specification for Perforated-Plate Sieves for Testing Purpose
17、s3. Terminology3.1 For definitions of general terms used in this test method see Terminology C125.4. Significance and Use4.1 This test method provides a procedure for making a preliminary estimate of the soundness of aggregates for use in concreteand other purposes. The values obtained may be compar
18、ed with specifications, for example Specification C33C33/C33M, that aredesigned to indicate the suitability of aggregate proposed for use. Since the precision of this test method is poor (Section 1213),it may not be suitable for outright rejection of aggregates without confirmation from other tests
19、more closely related to the specificservice intended.4.2 Values for the permitted-loss percentage by this test method are usually different for fine and coarse aggregates, andattention is called to the fact that test results by use of the two salts differ considerably and care must be exercised in f
20、ixing properlimits in any specifications that include requirements for these tests. The test is usually more severe when magnesium sulfate isused; accordingly, limits for percent loss allowed when magnesium sulfate is used are normally higher than limits when sodiumsulfate is used.NOTE 2Refer to the
21、 appropriate sections in Specification C33C33/C33M establishing conditions for acceptance of coarse and fine aggregates whichfail to meet requirements based on this test.5. Apparatus5.1 SievesWith square openings of the following sizes conforming to Specifications E11 or E323, for sieving the sample
22、s inaccordance with Sections 67, 78, and 910:150 m (No. 100) 8.0 mm (516 in.)9.5 mm (38 in.)300 m (No. 50) 12.5 mm (12 in.)16.0 mm (58 in.)600 m (No. 30) 19.0 mm (34 in.)25.0 mm (1 in.)1.18 mm (No. 16) 31.5 mm (114 in.)2.36 mm (No. 8) 37.5 mm (112 in.)50 mm (2 in.)4.00 mm (No. 5) 63 mm (212 in.)larg
23、er sizes by4.75 mm (No. 4) 12.5-mm (12-in.)4.75 mm (No. 4) 12.5 mm (12 in.)spread5.2 ContainersContainers for immersing the samples of aggregate in the solution, in accordance with the procedure describedin this test method, shall be perforated in such a manner as to permit free access of the soluti
24、on to the sample and drainage of thesolution from the sample without loss of aggregate.NOTE 3Baskets made of suitable wire mesh or sieves with suitable openings are satisfactory containers for the samples.5.3 Temperature RegulationSuitable means for regulating the temperature of the samples during i
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMC88C88M2018STANDARDTESTMETHODFORSOUNDNESSOFAGGREGATESBYUSEOFSODIUMSULFATEORMAGNESIUMSULFATEPDF

链接地址:http://www.mydoc123.com/p-508641.html