ASTM C778-2012 Standard Specification for Standard Sand 《标准砂用标准规格》.pdf

《ASTM C778-2012 Standard Specification for Standard Sand 《标准砂用标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM C778-2012 Standard Specification for Standard Sand 《标准砂用标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C778 12Standard Specification forStandard Sand1This standard is issued under the fixed designation C778; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the

2、year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification covers standard sand for use in thetesting of hydraulic cements.1.2 Th

3、e values stated in SI units are to be regarded as thestandard.1.3 Values in SI units shall be obtained by measurement inSI units or by appropriate conversion, using the Rules forConversion and Rounding given in IEEE/ASTM SI 10,ofmeasurements made in other units.1.4 This standard does not purport to

4、address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C109/C109M

5、 Test Method for Compressive Strength ofHydraulic Cement Mortars (Using 2-in. or 50-mm CubeSpecimens)C127 Test Method for Density, Relative Density (SpecificGravity), and Absorption of Coarse AggregateC136 Test Method for Sieve Analysis of Fine and CoarseAggregatesC150 Specification for Portland Cem

6、entC185 Test Method for Air Content of Hydraulic CementMortarC595 Specification for Blended Hydraulic CementsC702 Practice for Reducing Samples of Aggregate to Test-ing SizeC1005 Specification for Reference Masses and Devices forDetermining Mass and Volume for Use in the PhysicalTesting of Hydraulic

7、 CementsE11 Specification for Woven Wire Test Sieve Cloth and TestSievesIEEE/ASTM SI 10 Standard for Use of the InternationalSystem of Units (SI): The Modern Metric System3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 2030 sand, nstandard sand, predominantly gradedto pass a 8

8、50-m (No. 20) sieve and be retained on a 600-m(No. 30) sieve.3.1.2 graded sand, nstandard sand, predominantly gradedbetween the 600-m (No. 30) sieve and the 150-m (No. 100)sieve.3.1.3 standard sand, nsilica sand, composed almost en-tirely of naturally rounded grains of nearly pure quartz, usedfor pr

9、eparing mortars in the testing of hydraulic cements.4. Requirements4.1 Sand shall meet the requirements of Table 1 with respectto grading, source of sand, and absence of undesirable airentraining characteristics.METHODS OF SAMPLING AND TESTINGSTANDARD SANDS5. Apparatus5.1 SievesThe sieves shall be s

10、tandard 203-mm (8-in.)diameter, full-height, wire-cloth sieves, conforming to therequirements of Specification E11, and of the following sizes:1.18-mm (No. 16) 425-m (No. 40)850-m (No. 20) 300-m (No. 50)600-m (No. 30) 150-m (No. 100)5.2 Sample SplitterThe sample splitter, receptacles, andfeeder pan

11、or hopper shall conform to the general designrequirements listed in Method A, apparatus section of PracticeC702, except that the device shall have no fewer than eightchutes having a maximum opening no greater than 13 mm, and1This specification is under the jurisdiction of ASTM Committee C01 onCement

12、 and is the direct responsibility of Subcommittee C01.95 on Coordination ofStandards.Current edition approved May 1, 2012. Published June 2012. Originallyapproved in 1974. Last previous edition approved in 2006 as C778 06. DOI:10.1520/C0778-12.2For referenced ASTM standards, visit the ASTM website,

13、www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Driv

14、e, PO Box C700, West Conshohocken, PA 19428-2959, United States.a minimum opening at least three times the diameter of thelargest particle of sand in a sample to be split.5.3 Scales, Balances, and Reference MassesScales, bal-ances, and reference masses shall conform to the requirementsof Specificati

15、on C1005 as appropriate for the size of the samplethe mass of which is to be determined.6. Sampling6.1 Sample each lot or shipment and test for the gradingrequirements in Table 1. Determine air entraining characteris-tics only when contamination of sand is suspected. Sample theshipment in accordance

16、 to the procedure listed in 9.1.6.2 ProcedureUsing Method AMechanical Splitter pro-cedure described in Practice C702, reduce the entire contentsof a bag of standard sand to a testing size of approximately 300g.7. Sieve Analysis7.1 SievingSieve the sand by hand or mechanically asdescribed in Test Met

17、hod C136.7.2 ReportingReport the results of the sieve analysis astotal percentage passing each sieve.8. Tests for Air-Entraining Potential of Sand8.1 Small amounts of some surfactants or other contami-nants will produce air voids in mortars made with 2030 sand,graded sands or both. When contaminatio

18、n is suspected, testthe sands in accordance with the procedures described in thissection to determine the effect on air content or strength (seeNote 1).NOTE 1It may be desirable to wash these sands routinely to avoidpotential problems. Additionally, the washing procedure outlined in 8.1.1will tend t

19、o minimize segregation of sand that may occur when the sandis handled in a dry state.8.1.1 Obtain a sample of at least 2800 g from a full bag ofsand. Place the remainder of the sand from the bag in aconcrete mixer of the drum type. Add sufficient water to coverthe sand and mix for 2 min. Decant the

20、water over a 75 msieve and drain for 2 min. Repeat the washing and decantingprocedure four times. Tilt the mixer and drain the sand for 20min or longer. Determine the mass of damp sand and place itin approximately batch-sized quantities in separate containers.Dry the sand to constant mass in an oven

21、 at 110 C. Cool andadjust the quantity of dry sand to the amount required for a test.Prepare two batches of each of “washed” and as “as received”sand for test following the procedures in Test Method C185 for2030 sand or Test Method C109/C109M for graded sand.8.1.2 Tests for air-entraining potential

22、of a standard sandshall be made on a single day by a single operator.8.2 2030 SandPrepare two batches of mortar withwashed sand and two with “as received” sand in accordancewith Test Method C185. Compare the average air content forwashed and unwashed sand mortars for compliance with limitin Table 1.

23、8.3 Graded SandPrepare two batches of mortar withwashed sand and two with “as received” sand in accordancewith Test Method C109/C109M. (See Note 2.) When TestMethod C109/C109M mortar cubes are removed from themolds, determine the density of a group of at least three cubesfrom each batch by determini

24、ng the mass of the cubes both inair and immersed in water. Follow procedures outlined in TestMethod C127 for bulk specific gravity (SSD). Determine themass of the cubes to at least the nearest gram. Calculate theapparent air content as follows:apparent air content 5 Dt2 Dm!/Dt! 3 100 (1)where:Dm= th

25、e measured density (bulk specific gravity (SSD),andDt= the theoretical density of air-free mortar, g/cm3.Note that Dtis calculated as the total mass of the ingredientsin a batch of mortar divided by the sum of the absolute volumesof the cement, sand, and water used in the batch. Average theapparent

26、air content of the two batches made with washed sandand compare that average with the similar average for “asreceived sand” mortar to determine compliance with the limitin Table 1.NOTE 2Compressive strength of Test Method C109/C109M mortarmade with Specification C150 or C595 cement will be reduced a

27、pproxi-mately 4 % for each percent of air in the compacted cube. However, asmany as three batches of washed and three of unwashed sand may beneeded to reliably detect a difference in strength of 7 % between washedand unwashed sand mortars.9. Rejection9.1 Standard SandReject a bag of standard sand if

28、 thecontents fail to meet one or more of the requirements of thisspecification. Sample a shipment of standard sand by selectingevery 15th bag by consecutive number beginning with the 5thbag of the shipment. Count bags missing from the sequence asif they were there. Accept a shipment of standard sand

29、 if thecontents of the selected bags meet the requirements of thisspecification. If any of the selected bags fail to meet one ormore of the requirements of this specification, resample theshipment by selecting every 15th bag by consecutive numberbeginning with the 10th bag of the shipment. Accept as

30、hipment of standard sand if the contents of the selected bagson the resampling meet the requirements of this specification.If any of the selected bags in the resampling fail to meet one ormore of the requirements of this specification, and the rejectedbag is within a 15-bag sequence of a bag rejecte

31、d in the firstselection of bags, reject the entire sequence of bags betweenTABLE 1 Standard Sand RequirementsCharacteristics 20-30 Sand Graded SandGrading, percent passing sieve:1.18 mm (No. 16) 100 100850 m (No. 20) 85 to 100600 m (No. 30) 0 to 5 96 to 100425 m (No. 40) 65 to 75300 m (No. 50) 20 to

32、 30150 m (No. 100) 0 to 4Difference in air content of mortars madewith washed and unwashed sand, max,%airA2.0 1.5Source of sand Ottawa, IL orLeSuer, MNOttawa, ILAThis determination is needed when contamination of sand is suspected asdiscussed in 8.1.C778 122accepted tests. Reject the entire shipment

33、 if half of the numberof bags tested fail to meet the requirements of this specifica-tion, or if the shipment consists of five bags or less if onerandomly selected bag fails the specification.9.2 Table 2 shows for both sampling and resampling inColumn 2 the number of bags to be tested based on the t

34、otalnumber of consecutive bags in the shipment. Column 3 showsthe identification of the bag to be selected for test based on theconsecutive number of the bags.NOTE 3For example, if, in a shipment of 30 bags, on first sampling,the 20th bag fails the specification, and on resampling, the 25th bag fail

35、sthe specification, the entire shipment is rejected. If the shipment were 100bags and on first sampling only the 20th bag fails, and on resampling onlythe 25th bag fails, only bags Nos. 11 to 34 would be rejected.10. Packaging and Package Marking10.1 PackagingStandard sands shall be delivered in bag

36、swith impervious liners made of material that will not contami-nate the sand.10.2 MarkingEach bag shall be plainly marked as fol-lows:ASTM C778 20-30 Sand orASTM C778 Graded Sand asthe case may be. The source of the sand and the mass of thesand contained therein shall be plainly indicated on each ba

37、g.11. Keywords11.1 20-30 sand; graded sand; hydraulic cement testingsand; standard sandSUMMARY OF CHANGESCommittee C01 has identified the location of selected changes to this specification since the last issue,C778 06, that may impact the use of this specification. (Approved May 1, 2012)(1) Revised

38、5.3.(2) Revised 6.2.(3) Revised Table 1 moved note B.(4) Moved note B to 8.3 as Note 2.Committee C01 has identified the location of selected changes to this specification since the last issue, C778 02, that mayimpact the use of this specification. (Approved May 15, 2006)(1) Revised 5.2.(2) Added new

39、 6.1.(3) Revised 9.1 and Note 3.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof

40、infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this st

41、andard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your

42、 views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by cont

43、acting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 2 Sampling and Resampling of S

44、tandard SandTotal No. of ConsecutiveBags in ShipmentNo. of Bagsto TestTest in Consecutive No., theFollowing BagsSampling:less than 5 1 random5to19 1 5th20 to 34 2 5th and 20th35 to 49 3 5th, 20th, and 35th50 to 64 4 5th, 20th, 35th, and 50thResampling:less than 5 none reject shipment5to19 1 10th20 to 34 2 10th and 25th35 to 49 3 10th, 25th, and 40th50 to 64 4 10th, 25th, 40th, and 55thC778 123