ASTM C476-2018 Standard Specification for Grout for Masonry.pdf

《ASTM C476-2018 Standard Specification for Grout for Masonry.pdf》由会员分享，可在线阅读，更多相关《ASTM C476-2018 Standard Specification for Grout for Masonry.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C476 16C476 18Standard Specification forGrout for Masonry1This standard is issued under the fixed designation C476; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses ind

2、icates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification covers two types of grout, fine and coarse grout, for

3、use in the construction of masonry structures. Eachtype (fine and coarse) is further classified as conventional grout (requiring mechanical consolidation by puddling or vibration whenplaced) and self-consolidating grout (not requiring mechanical consolidation when placed). Conventional grout is spec

4、ified by (1)proportions or (2) strength requirements. Self-consolidating grout is specified by strength requirements.1.2 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes(excluding those in tables and figures) shall not be cons

5、idered as requirements of this specification.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information only and are not considered standard.1.4 This international standard was de

6、veloped in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Docu

7、ments2.1 ASTM Standards:2C5 Specification for Quicklime for Structural PurposesC143/C143M Test Method for Slump of Hydraulic-Cement ConcreteC150/C150M Specification for Portland CementC207 Specification for Hydrated Lime for Masonry PurposesC260/C260M Specification for Air-Entraining Admixtures for

8、ConcreteC404 Specification for Aggregates for Masonry GroutC494/C494M Specification for Chemical Admixtures for ConcreteC595/C595M Specification for Blended Hydraulic CementsC618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in ConcreteC989/C989M Specification for Slag

9、Cement for Use in Concrete and MortarsC1019 Test Method for Sampling and Testing GroutC1157/C1157M Performance Specification for Hydraulic CementC1611/C1611M Test Method for Slump Flow of Self-Consolidating Concrete3. Materials3.1 Materials used as ingredients in grout shall conform to the requireme

10、nts specified in 3.1.1 3.1.53.1.8.3.1.1 Cementitious MaterialsCementitious materials shall conform to one of the following specifications:3.1.1.1 Portland CementType I, IA, II, IIA, III, and IIIA of Specification C150/C150M.3.1.1.2 Blended CementsType IL, IS(70), IP, IT(S70), or blended cements with

11、 special properties designated by (A), (MS),or (HS), or a combination of (A) and (MS) or (HS), as appropriate, of Specification C595/C595M.1 This specification is under the jurisdiction of ASTM Committee C12 on Mortars and Grouts for Unit Masonryand is the direct responsibility of Subcommittee C12.0

12、5on Grout cement; compressive strength; grout; masonry; portland cement; proportions ; self-consolidating groutSUMMARY OF CHANGESCommittee C12 has identified the location of selected changes to this standard since the last issue(C476 10C476 16) that may impact the use of this standard. (July (May 1,

13、 201815, 2016)(1) AddedRevised 3.1.5.13.1.1.2 and added a new 3.1.1.3. Renumbered subsequent subsections. Revised Note 3to permit Type Band D (old Note 1) to create a new note (Note 4admixtures.).(2) ModifiedChanged 3.1.6 to clarify approval of pumping aids.3.1.2 through 3.17, including the addition

14、 of Note 1 and relocationof Note 2.C476 184ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and

15、the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revision

16、of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shoul

17、dmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtain

18、ed by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 185