ASTM C1546-2002(2014) Standard Guide for Installation of Gypsum Products in Concealed Radiant Ceiling Heating Systems《隐蔽式天花板辐射加热系统中石膏制品安装的标准指南》.pdf

《ASTM C1546-2002(2014) Standard Guide for Installation of Gypsum Products in Concealed Radiant Ceiling Heating Systems《隐蔽式天花板辐射加热系统中石膏制品安装的标准指南》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1546-2002(2014) Standard Guide for Installation of Gypsum Products in Concealed Radiant Ceiling Heating Systems《隐蔽式天花板辐射加热系统中石膏制品安装的标准指南》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1546 02 (Reapproved 2014)Standard Guide forInstallation of Gypsum Products in Concealed RadiantCeiling Heating Systems1This standard is issued under the fixed designation C1546; the number immediately following the designation indicates the year oforiginal adoption or, in the case of r

2、evision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide2provides information for trades installinggypsum products in conjunction with a concea

3、led radiantceiling heating system constructed from thin sheet flexibleradiant heating panels, and for the installation of gypsumproducts after repair of existing concealed radiant ceilingheating systems constructed from heating cable or thin sheetflexible radiant heating panels.1.2 The values stated

4、 in inch-pound units are to be regardedas standard. No other units of measurement are included in thisstandard.1.3 This guide does not purport to address any aspect ofconcealed radiant heating system design or performance, and islimited to the proper installation of gypsum products specifiedfor use

5、in a concealed radiant ceiling heating system.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regul

6、atory requirements prior to use.1.5 The text of this standard references notes and footnoteswhich provide explanatory material. These notes and footnotesshall not be considered as requirements of the standard.2. Referenced Documents2.1 ASTM Standards:3C840 Specification forApplication and Finishing

7、of GypsumBoardC841 Specification for Installation of Interior Lathing andFurringC842 Specification for Application of Interior Gypsum Plas-ter3. Terminology3.1 Definitions:3.1.1 concealed radiant heating system, na system thatoperates by heating the building materials that conceal the heatsource, wh

8、ich in turn transfer the heat into the heated area byradiant emission.3.1.2 facing, nthe finished surface layer through whichheat is transferred into a heated area.3.1.3 flexible radiant heating panel, na thin sheet heatingelement intended to produce heat when connected to anelectrical supply.3.1.4

9、furring, nspacer elements added to a building struc-ture to facilitate fastening of gypsum panel products.3.1.5 gypsum product, nbuilding material intended for usein radiant heated ceiling construction, containing gypsum in itscomposition or construction.3.1.5.1 DiscussionThe gypsum products most of

10、ten asso-ciated with radiant heating systems are gypsum board andgypsum plaster.3.1.6 heating cable, nan electrically insulated cable in-tended to produce heat when connected to an electrical supply.4. Significance and Use4.1 The purpose of this guide is to provide information togypsum product insta

11、llers for the avoidance of hazards asso-ciated with the installation of gypsum products adjacent to, orsurrounding, electric heating components and conductors; andto avoid damage to gypsum products when used in conjunctionwith a concealed radiant heating system.4.2 The information given in this guid

12、e is applicable torepair of existing cable heating systems and to new construc-tion of radiant heating systems constructed from flexibleradiant heating panels.5. Summary of Guide5.1 Heating System Design:1This guide is under the jurisdiction of ASTM Committee C11 on Gypsum andRelated Building Materi

13、als and Systems and is the direct responsibility ofSubcommittee C11.03 on Specifications for the Application of Gypsum and OtherProducts in Assemblies.Current edition approved April 1, 2014. Published April 2014. Originallyapproved in 2002. Last previous edition approved in 2008 as C1546 02 (2008)1.

14、DOI: 10.1520/C1546-02R14.2The first edition of this guide replaced Appendix X.7 of SpecificationC840 - 99a.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the stand

15、ards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.1.1 The heating system shall be designed to satisfy theheating needs of the building and to work effectively with allbuilding materials sp

16、ecified for use in the heating systeminstallation.NOTE 1The architect bears the responsibility of preparing andcorrelating complete plans and specifications, and to engage a professionalfamiliar with the heating system to design the system to meet therequirements of 5.1.1 and 5.1.2.5.1.2 The heating

17、 system shall be designed so that a gypsumproduct is not exposed to a temperature more than 125F(52C) for periods of time sufficient to cause calcination.NOTE 2The foregoing requirement is intended to provide guidance toheating system designers, consistent with Specification C840,intheabsence of a c

18、omprehensive radiant heating system standard.5.2 Installation of Heating Equipment:5.2.1 Installation of radiant heating and related electricalequipment is governed by codes and regulations, and is theresponsibility of other trades.5.3 General Installation Guidelines:5.3.1 The application of gypsum

19、panel products under thisguide shall be performed in accordance with SpecificationC840, except as herein modified.5.3.2 The radiant heating system shall be disconnected fromthe electric supply prior to the commencement of work.NOTE 3Disconnection from the electric supply is accomplished byswitching

20、the heating system circuit breakers off, or removing fuses.Lowering a thermostat setting until the heating system turns off is notsupply disconnection.5.3.3 Unless the concealed radiant heating system is nolonger in use and has been permanently disconnected from theelectrical supply, or unless the p

21、revious facing has beenremoved, gypsum panel products or gypsum plaster shall notbe installed as a new facing on the heated area side of anexisting concealed radiant heating system.NOTE 4The increased thickness resulting from addition of gypsumpanel products or gypsum plaster to an existing conceale

22、d radiant heatingsystem can impair heat transfer into the heated area, and may causeoverheating of the electrical heat source.5.3.4 All inspection and testing of the heating system shallbe completed before application of gypsum facing materials.5.3.5 Care shall be taken in the installation of fasten

23、ers toavoid the penetration of heating equipment and electricalconductors.5.3.6 The radiant heating system shall not be operated toaccelerate the drying of joint compound or texture finishes.5.3.7 Follow the radiant heat-source manufacturers start-upand operating instructions when operating the radi

24、ant heatingsystem.5.4 Repair of Cable Heating Systems:5.4.1 Repair of heating cables is the responsibility of othertrades.5.4.2 The application of gypsum plaster shall conform toSpecification C842 except as herein modified.5.4.3 Filler added to gypsum plaster used to repair a heatingcable system, if

25、 any, shall be of sand or similar thermallyconductive material. Thermal insulating fillers such as ver-miculite or perlite, and foaming agents that impair heat transfershall not be used in plaster applied to radiant heating systems.5.4.4 Application of metal lath shall conform to Specifica-tion C841

26、. Metal lath and fasteners installed for repair of acable heating system shall not contact heating cables.5.4.5 Complete embedding of the heating cable in plaster isnecessary after cable repair is completed.5.5 Flexible Radiant Heating Panel Systems:5.5.1 Application of gypsum panel products shall c

27、omplywith the requirements for System I or System II of Specifica-tion C840, as applicable, based on the specified number oflayers; and with the requirements of System XII where floatinginterior angles are used.5.5.2 Application of gypsum panel products to steel framingor furring shall comply with S

28、ystem VIII of SpecificationC840.5.5.3 The thickness of a gypsum panel product installed asa facing shall not exceed the thickness specified in the heatingsystem design specification.NOTE 5Installing facing thicker than specified can impair heattransfer into the heated area, and may cause overheating

29、 of the electricalheat source.5.5.4 Furring of any material or construction shall not beinstalled between gypsum panel product facing and flexibleradiant heating panels.NOTE 6The air gap produced by furring can impair heat transfer intothe heated area, and may cause flexible radiant heating panels t

30、o overheat.5.5.5 All joints and heads of fasteners shall be finished inaccordance with Specification C840, to the specified level offinish.NOTE 7When repairing an existing surface, the level of finish of therepair should be the same as that of the original surface.5.5.6 Foil backed gypsum panel prod

31、ucts shall not beinstalled in contact with thin sheet flexible radiant heatingpanels.5.6 Decoration:5.6.1 The heating system shall be turned off and allowed tocool before decorating.5.6.2 Decoration of finished work, including sizing orsealing, shall not proceed until joint compound has dried.5.6.3

32、When texture finishes are used, such finishes must bethoroughly dry prior to heating system operation.6. Keywords6.1 furring; gypsum panel product; gypsum plaster; heatingcable; heating panel; lath; radiant heatC1546 02 (2014)2ASTM International takes no position respecting the validity of any paten

33、t rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision a

34、t any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your commen

35、ts will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted

36、by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C1546 02 (2014)3