ASTM C1535-2005(2011) Standard Practice for Application of Exterior Insulation and Finish Systems Class PI《PI级外部绝缘和装饰系统的应用的标准实施规程》.pdf

《ASTM C1535-2005(2011) Standard Practice for Application of Exterior Insulation and Finish Systems Class PI《PI级外部绝缘和装饰系统的应用的标准实施规程》.pdf》由会员分享，可在线阅读，更多相关《ASTM C1535-2005(2011) Standard Practice for Application of Exterior Insulation and Finish Systems Class PI《PI级外部绝缘和装饰系统的应用的标准实施规程》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C1535 05 (Reapproved 2011)Standard Practice forApplication of Exterior Insulation and Finish Systems ClassPI1This standard is issued under the fixed designation C1535; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, th

2、e year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This practice covers the minimum requirements andprocedures for field or prefabricated application of Class

3、 PIExterior Insulation and Finish Systems (EIFS). Class PI EIFSare systems applied over polyisocyanurate insulation board, inwhich the base coat ranges from not less than116 in. (1.6 mm)to14 in. (6.4 mm) in dry thickness, depending upon the numberof nonmetallic reinforcing mesh layers encapsulated i

4、n the basecoat. The base coat is then covered with a finish coat of variousthickness in a variety of textures and colors. The insulationboard shall be applied over a substrate or over open framing.1.2 This practice does not cover Class PI EIFS with drain-age. Consult the EIFS producer for informatio

5、n.1.3 The values stated in inch-pound units are to be regardedas the standard. The SI (metric) values given in parentheses areapproximate and are provided for information purposes only.1.4 The text of this standard references notes and footnotesthat provide explanatory material. These notes and foot

6、notesshall not be considered as requirements of the standard.1.5 This standard may involve hazardous materials, opera-tions and equipment. This standard does not purport to addressall of the safety concerns, if any, associated with its use. It isthe responsibility of the user of this standard to est

7、ablishappropriate safety and health practices and determine theapplicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C11 Terminology Relating to Gypsum and Related BuildingMaterials and SystemsC79/C79M Specification for Gypsum Sheathing Board3C150 Specificat

8、ion for Portland CementC1063 Specification for Installation of Lathing and Furringto Receive Interior and Exterior Portland Cement-BasedPlasterC1177/C1177M Specification for Glass Mat Gypsum Sub-strate for Use as SheathingC1186 Specification for Flat Fiber-Cement SheetsC1278/C1278M Specification for

9、 Fiber-Reinforced Gyp-sum PanelC1280 Specification for Application of Gypsum SheathingC1289 Specification for Faced Rigid Cellular Polyisocya-nurate Thermal Insulation BoardC1325 Specification for Non-Asbestos Fiber-Mat Rein-forced Cementitious Backer UnitsC1382 Test Method for Determining Tensile A

10、dhesionProperties of Sealants When Used in Exterior Insulationand Finish Systems (EIFS) JointsC1472 Guide for Calculating Movement and Other EffectsWhen Establishing Sealant Joint WidthC1481 Guide for Use of Joint Sealants with Exterior Insu-lation and Finish Systems (EIFS)E1825 Guide for Evaluation

11、 of Exterior Building WallMaterials, Products, and SystemsE2110 Terminology for Exterior Insulation and Finish Sys-tems (EIFS)3. Terminology3.1 Definitions used in this standard shall be in accordancewith Terminologies C11 and E2110.4. Significance and Use4.1 This practice provides minimum requireme

12、nts for theapplication of Class PI EIFS. The requirements for materials,mixtures, and details shall be contained in the project plans andspecifications. See Guide E1825 for guidance.5. Delivery of Materials5.1 All materials shall be delivered in packages, containers,or bundles with the identificatio

13、n and markings intact.1This practice is under the jurisdiction of ASTM Committee C11 on Gypsumand Related Building Materials and Systems and is the direct responsibility ofSubcommittee C11.05 on Application of Exterior Insulating and Finish Systems andRelated Products.Current edition approved Dec. 1

14、, 2011. Published June 2012. Originallyapproved in 2002. Last previous edition approved in 2005 as C1535 05. DOI:10.1520/C1535-05R11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume infor

15、mation, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700,

16、West Conshohocken, PA 19428-2959, United States.6. Inspection6.1 Inspection of the materials shall be agreed upon and bea part of the purchase agreement.6.2 Inspection shall include the determination that the ma-terials supplied are as required for the Class PI EIF Systemspecified. Mixing of materia

17、ls from different manufacturers isnot allowed.7. Rejection7.1 Materials that are damaged, frozen or defective shall notbe used. Rejection of materials shall be promptly reportedverbally to the producer and immediately reported in writing.The notice of rejection shall contain a statement documentingt

18、he basis for material rejection.8. Certification8.1 When specified in the contract documents, the producershall furnish a report certifying that the materials are inconformance with product and material standards and contractdocuments.8.2 Insulation Boards:8.2.1 Insulation boards shall be in complia

19、nce with Speci-fication C1289 , Type II, Class 2.8.2.2 Insulation boards shall have been subjected to a thirdparty quality control inspection and shall be marked asapproved for use within the EIFS and in accordance withapplicable building code.8.2.3 Prior to installation, the insulation board shall

20、beinspected for conformance with contract documents. Noncon-forming insulation board shall not be used.8.2.4 The insulation board producer shall furnish, for eachshipment, a written certificate of conformance with the EIFSproducers specifications.9. Storage of Materials9.1 All materials shall be kep

21、t dry by storage under coverand protected from the weather. When outside storage isrequired, materials shall be stacked off the ground, supportedon a level platform and protected from the weather, surfacecontamination or physical damage in accordance with the EIFSproducers written instructions.9.2 M

22、aterials shall be protected from exposure to directsunlight and temperatures less than 40 F (4 C) unlessotherwise specified by the manufacturer.9.3 Portland Cement shall meet Specification C150 andshall be kept dry until ready for use. It shall be kept off theground, under cover and away from damp w

23、alls and surfaces.9.4 Insulation board shall be stacked flat with care taken toavoid damage to edges, ends, or surfaces; or exposure to directsunlight (ultraviolet radiation).10. Environmental Conditions10.1 Cold Weather Conditions:10.1.1 Wet materials shall not be applied when the tempera-ture is l

24、ess than 40 F (4 C) unless otherwise specified by themanufacturer or unless temporary heat and enclosures areprovided to maintain minimum 40 F (4 C) for a minimumperiod of not less than 24 hours before, during and afterapplication. (See X1.8.3)10.1.2 Materials shall not be applied to a base containi

25、ngfrost. Substrate surface temperature shall be not less than 40 F(4 C). Mixtures for application shall not contain any frozeningredients.11. Assessment of Condition of Substrates to ReceiveExterior Insulation and Finish Systems11.1 The substrate shall be as required by the project plansand specific

26、ations and as recommended by the EIFS producerfor the particular system specified.11.1.1 Polyisocyanurate boards for use over open framing inconformance with the EIFS producers specification shall notbe less than 1.0 in. (25.4 mm) in thickness.11.1.2 Polyisocyanurate boards for use over a substrate

27、inconformance with the EIFS producers specification shall notbe less than58 in. (15.9 mm) in thickness.NOTE 1Polyisocyanurate board thickness shall conform to buildingcode requirements.11.2 The substrate shall be inspected by the applicator andgeneral contractor to assure that it meets the project p

28、lans andspecifications and the requirements of 11.3-11.8.11.3 Sheathing materials shall be inspected to ensure thefollowing:11.3.1 The specified sheathing thickness has been installedfor the stud spacing used.11.3.2 Fastener type and fastener spacing are as specified.11.3.3 All Specification C79/C79

29、M gypsum sheathingboards have a water-resistant treated core.11.3.4 Tongue and groove water-resistant core gypsumsheathing boards conforming to Specification C79/C79M areinstalled with the tongue edge oriented to the top.11.3.5 Gypsum sheathing shall be installed with the facepaper exposed in accord

30、ance with Specification C1280.11.3.6 Gypsum sheathing shall be protected from moistureat all penetrations and terminations.11.3.7 Glass mat gypsum sheathing complying with Speci-fication C1177/C1177M shall be installed in accordance withthe sheathing producers written installation instructions,which

31、 include details of framing type and spacing, fastenertype and spacing, and sheathing orientation and spacing.11.3.8 Plywood shall be not less than12 in. (12.7 mm)nominal in thickness, exterior or exposure 1 panel sheathing.The plywood shall be installed with a18 in. (3.2 mm) spacebetween sheets at

32、edges and ends.11.3.9 Fiber-Cement sheets complying with SpecificationC1186, Type A, shall be installed in accordance with the sheetproducers written installation instructions, which include de-tails of stud type and spacing, fastener type and spacing, andsheet spacing recommendations.11.3.10 Water-

33、resistant exterior fiber-reinforced gypsumsheathing complying with Specification C1278/C1278M shallbe installed in accordance with the sheathing producerswritten installation instructions, which include details of fram-ing type and spacing, fastener type and spacing, and sheathingorientation and spa

34、cing.11.3.11 Fiber-mat reinforced cement sheets complying withSpecification C1325, type A, shall be installed in accordancewith the sheet producers written installation instructions,C1535 05 (2011)2which include details of framing type and spacing, fastenertype and spacing, and sheet orientation and

35、 spacing.11.3.12 Sheathing shall be continuous.11.4 AlignmentAll substrate surfaces shall be straight andtrue within14 in./10 ft (2 mm/m). More stringent requirementsby the EIFS producer shall supersede the above stated require-ments.11.5 Suitability for UseThe substrate shall be firm, sound,and und

36、amaged in order to receive the EIFS.11.6 CleanlinessThe surface of all substrates shall beclean and free from any foreign materials such as paint, formrelease agents, curing compounds, dust, dirt, frost, oil orgrease, efflorescence and laitance that would affect the EIFSapplication.11.7 Dryness:11.7

37、.1 Newly constructed concrete or masonry surfacesshall be allowed to cure not less than 28 days prior toapplication of the EIFS. Repaired areas on existing (aged)walls shall meet the same 28-day curing time.11.7.2 Substrate surfaces shall be free of visible water.11.8 Metal Lath or Furring and Acces

38、soriesIf metal lathor furring and accessories are used, they shall be installed inconformance with Specification C1063, except lath edges andends shall be butted and not lapped. Metal lath shall be 3.4lb/yd2(1.3 kg/m2) self-furring, galvanized.11.8.1 Metal members shall be properly attached, straigh

39、t,and true unless otherwise required by the system design.11.8.2 Metal members shall be free of rust, oil, or otherforeign matter or contaminants, which cause bond failure orunsightly discoloration.12. Insulation Board Installation12.1 Method of Attachment shall be approved by thesystem producer and

40、 be in accordance with applicable buildingcode.12.2 Mechanical Attachment Method:12.2.1 Mechanical fasteners shall be installed into the fram-ing or nailable substrate.12.2.2 Mechanical fasteners shall be corrosion resistant.Fastener type and spacing shall be in accordance with systemproducers curre

41、nt published instructions.NOTE 2Specific consideration of building code wind load require-ments shall be given for mechanically fastened systems.12.3 Placement of a weather resistive barrier, if specified,shall be as required by the system producer.13. General Requirements13.1 Insulation boards shal

42、l be placed from a level base linewith vertical joints staggered in a running bond pattern andbutted tightly. Over open framing, joints shall occur overframing or horizontal blocking.13.2 Insulation board joints at all inside and outside cornersshall be staggered and interlocked.13.3 Insulation boar

43、ds must abut without gaps, eliminatingspace for base coat intrusion between the board edges andends.13.4 Fenestration opening corners and other wall penetra-tions shall be cut out of a single insulation board. Board jointsshall not be aligned at corners with head, sill or jambs ofwindows, doors, sim

44、ilar openings, and aesthetic reveals.13.5 Mechanically Fastened:13.5.1 Insulation board joints shall be offset from sheathingboard joints.13.5.2 When the boards are attached only with mechanicalfasteners, they shall be affixed to a nailable substrate orstructural members with the proper fasteners, e

45、nsuring that allboards abut tightly. Fastening pattern shall be in accordancewith the EIFS producers recommendation and local buildingcode requirements. When installed, the washer shall be leftflush with the face of the insulation board and shall not fracturethe face or core of insulation board.14.

46、Aesthetic Reveals14.1 Aesthetic reveals shall be cut into the insulation boardprior to applying the reinforcing mesh.14.2 The insulation board thickness at the bottom of a revealshall be not less than34 in. (19.0 mm). Over open framing,aesthetic reveals shall occur over framing or blocking.14.3 Aest

47、hetic reveals shall be cut true and straight.14.4 Horizontal aesthetic reveal configuration shall providefor outward positive drainage.14.5 Aesthetic reveals shall not occur at the abutment of twopieces of insulation board.14.6 The reveal shall be reinforced with base coat andreinforcing mesh prior

48、to application of the full base coat andreinforcing mesh.15. Reinforced Base Coat Application15.1 Inspect the insulation board surface to ensure that it isclean, dry, free of all foreign materials, and damage of anytype. Insulation board planar irregularities of more than116 in.(1.6 mm) shall be cor

49、rected. All board joints shall be tightlyabutted or shall be filled with an insulating material.15.2 Base Coat PreparationAll materials requiring fieldpreparation shall be mixed in accordance with the EIFSproducers specifications.15.3 Base Coat ApplicationThe prepared base coat shallbe uniformly spread over the entire surface of the insulationboard.15.4 Non Metallic Reinforcing MeshThe single layerreinforcing mesh shall be fully encapsulated in the field of thewall, at corners, edges, and joints. Trowel from the center to theedge of the reinforcin