ASTM C1087-2000(2006) Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems《测定门窗玻璃结构装置中与附件一同使用的液态密封料相容性的.pdf

《ASTM C1087-2000(2006) Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems《测定门窗玻璃结构装置中与附件一同使用的液态密封料相容性的.pdf》由会员分享，可在线阅读，更多相关《ASTM C1087-2000(2006) Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems《测定门窗玻璃结构装置中与附件一同使用的液态密封料相容性的.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C 1087 00 (Reapproved 2006)Standard Test Method forDetermining Compatibility of Liquid-Applied Sealants withAccessories Used in Structural Glazing Systems1This standard is issued under the fixed designation C 1087; the number immediately following the designation indicates the year ofor

2、iginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers a laboratory screening proce-dure fo

3、r determining the compatibility of liquid-applied struc-tural sealant glazing sealants when in contact with accessoriessuch as dry glazing gaskets, spacers, shims, and setting blocksafter exposure to heat and ultraviolet light.1.2 This test method includes the observation of threeparameters as follo

4、ws:1.2.1 Changes in the color of the sealant,1.2.2 Changes in the adhesion of the sealant to glass, and1.2.3 Changes in the adhesion of the sealant to the accessorybeing tested.1.3 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonl

5、y.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE 1At this

6、 time, no comparable ISO standard exists.2. Referenced Documents2.1 ASTM Standards:2C 717 Terminology of Building Seals and Sealants3. Terminology3.1 DefinitionsDefinitions of the following terms used inthis test method are listed in Terminology C 717: adhesivefailure (adhesion loss), bead, bond bre

7、aker, cohesive failure,compatibility, gasket, glazing, sealant, setting blocks, shim,spacer, structural sealant, and structural sealant glazing.4. Summary of Test Method4.1 The test specimens are placed beneath ultraviolet lampsso that the radiation will hit the sealant directly on onespecimen, and

8、through the glass, on the other specimen (seeFig. 1).4.2 The control specimens for this test method are preparedand tested identically to the test specimens except that theaccessory is eliminated.4.3 After the specimens are exposed, the test specimens arecompared to the control specimens.4.4 In the

9、testing of the specimens, any color change in thesealant between the test specimen and the control is noted asare any changes in the adhesion of the sealant to either the glassor to the accessory. This test method requires the preparation ofeight test specimens (four controls and four test specimens

10、 foreach accessory being evaluated).5. Significance and Use5.1 In structural sealant glazing systems, the sealant func-tions as the structural adhesive and may also function as theprimary weather seal. As the structural adhesive, the integrityof the adhesive bond is critical.5.2 Changes in color and

11、 adhesion after exposure are two ofthe criteria that can be used to determine the compatibility ofthe system. Experience has shown that accessories that causeloss of adhesion or discoloration in this test method may alsocause these occurrences in actual use.6. Apparatus and Materials6.1 Glass Panels

12、, clear float glass, approximately 76.2 by50.8 by 6.4 mm (3 by 2 by14 in.). Eight panels are required foreach material being tested.6.2 Bond Breaker Tape, 25.4 by 76.2-mm (1 by 3-in.) piecefor each panel. The bond breaker tape must be compatible withthe sealants being tested.6.3 Thermometer, for exa

13、mple, 28.9 to 100C (20 to 212F).6.4 Ultraviolet (UV) lamps, UVA-340 lamps.1This test method is under the jurisdiction ofASTM Committee C24 on BuildingSeals and Sealants and is the direct responsibility of Subcommittee C24.20 onGeneral Test Methods.Current edition approved May 1, 2006. Published Augu

14、st 2006. Originallyapproved in 1987. Last previous edition approved in 2000 as C 1087 00.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summ

15、ary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.5 UV Exposure ApparatusA suitable UV exposure ap-paratus will consist of four UVA-340 lamps in a symmetricalarray situated 254 mm (12 in.) from the surface

16、 of the testspecimens (see Fig. 2). The apparatus shall be capable ofmaintaining a temperature at the test specimens of 48 6 2C(118 6 3.6F). Infrared lamps or other sources of heat may beused to maintain the required temperature.6.6 Cleaning SolventAny solvent capable of cleaning theglass is accepta

17、ble (for example, 50/50 mix of isopropylalcohol and distilled water).6.7 Test Sealant, an appropriate amount of the sealant to beused in the system.6.8 Reference SealantA light or translucent sealant of thesame composition as the test sealant. If none is available,contact the sealant supplier for re

18、commendations on a suitablealternative.7. Preparation of Test Specimens7.1 Standard conditions of temperature and relative humid-ity used during the preparation are defined as 23 6 2C (73.463.6F) and 50 6 10 % relative humidity.7.2 Prior to use, clean the glass thoroughly with the cleaningsolvent an

19、d dry with a clean rag before the solvent is allowedto evaporate.7.3 Place a piece of compatible bond breaker tape to cover1 in. of the top surface of the glass at one end (see Fig. 3).7.4 Prepare a total of eight samples (four controls withoutaccessory and four test specimens with accessory).3Cut a

20、 pieceof accessory material approximately 6.4 by 51 by 6.4 mm (14by2by14 in.) and place it on the center of the piece of glassas shown in Fig. 3. Both the reference sealant and the testsealant are tested in contact with the accessory.7.5 Apply a bead of the test sealant on one side of theaccessory a

21、nd a bead of translucent or light color referencesealant along the other side of the accessory. Tool the sealant sothat good contact with the glass occurs and the sealant is on topof the accessory. The thickness of the sealant on top of theaccessory shall be approximately 3.2 mm (18 in.).7.6 The con

22、trol specimens for this test are prepared andtested identically to the test specimens except that the acces-sory is eliminated.8. Conditioning8.1 Condition all the specimens for one week at standardconditions. After conditioning for seven days at standardconditions, place two test specimens (with ac

23、cessory) and twocontrol specimens (without accessory) with glass side down,and place two test specimens (with accessory) and two controlspecimens (without accessory) with glass side up, under theUV lamps, in accordance with Fig. 1 (a)and1(b) for 21 days.8.2 In order to provide an appropriate intensi

24、ty of UVradiation, replace the UVA-340 lamps after eight weeks of use.In order to provide more uniform UV radiation, replace onelamp every two weeks, in accordance with the rotation schemeshown in Fig. 4. (Discard lamp No. 3, move lamp No. 2 to lamp3Control specimens need not be duplicated if more t

25、han one accessory is beingevaluated at one time.FIG. 1 Orientation of Test Specimen Under LampsFIG. 2 UV Exposure ApparatusFIG. 3 View of Test SpecimenFIG. 4 UV Lamp RotationC 1087 00 (2006)2position No. 3, move lamp No. 1 to lamp position No. 2, movelamp No. 4 to lamp position No. 1 then install th

26、e new lamp inlamp position No. 4.)8.3 The test chamber shall maintain an air temperature of 486 2C (118 6 3.6F) when measured at the surface of the testspecimens (see Fig. 2). Check test specimen surface tempera-tures at one-week intervals.9. Procedure9.1 Record orientation of sample under ultraviol

27、et lights(Fig. 1).9.2 At the end of the conditioning period described inSection 6, remove the specimens from the exposure apparatusand allow the warm samples to reach room temperature. (Coolfor 4 h.)9.3 Grasp the end of the sealant that is above the bondbreaker tape. Pull the sample on a 90 angle to

28、 the glass surfaceexerting force on the sealant/glass interface.9.3.1 Record the mode of failure in percent cohesive failure,C, for both the test and reference sealant as follows:C 5 100 2 % AL (1)where AL is the adhesion loss.9.4 Check the adhesion of the sealants to the accessory. Pullthe sealant

29、on a 90 angle to the accessory surface exertingforce on the sealant accessory interface.9.4.1 Record the mode of failure in percent cohesive failure(C).9.5 Observe the test and reference sealant.9.5.1 Using Table 1 as a guide, record and describe anycolor change in the test and reference sealants.9.

30、5.2 Record any other noticeable changes.9.6 Record data on report form (Fig. 5).10. Precision and Bias410.1 PrecisionRound-robin testing was performed bythree laboratories using two different sealants and four differentaccessory gaskets. Statistical analysis was performed by com-bining all four acce

31、ssory gaskets together for each set of tests,resulting in eight“ materials trialed,” instead of two for eachlaboratory.10.2 Repeatability, I(r)In future use of this test method,the difference between two test results obtained in the samelaboratory on the same material (the repeatability) will beexpe

32、cted to exceed I(r) only about 5 % of the time. Results forI(r) are given in Table 2.10.3 Reproducibility, I(R)In future use of this test method,the difference between two test results obtained in differentlaboratories on the same material (the reproducibility) will beexpected to exceed I(R) only ab

33、out 5 % of the time. Results forI(R) are given in Table 2.10.4 BiasSince there is no accepted reference materialsuitable for determining the bias for the procedures in this testmethod for measuring the color change and adhesion proper-ties, no statement on bias is being made.11. Keywords11.1 color c

34、hange; compatibility; staining; structural glaz-ing; structural sealant; ultra violet exposure4Supporting data are available from ASTM Headquarters. Request RR:C24-1020.TABLE 1 ASTM Test Method C 1087 Stain and Color ChangeDescriptionsNo. Color Change Change Description0 None No change from the cont

35、rol.1 Very, very slight Change so slight that you are notsure it is real.2 Very slight Faint colorgenerally yellow.3 Slight Light colorcommonly yellow,orange, pink, or brown.4 Severe Distinct colorpossibly red or purplein addition to yellow, orange, pink,or brown.5 Very severe Dark colormay be black

36、 as well asother colors mentioned.Note 1The colors listed in Table 1 are only the most commonly occurringcolors. Any change of appearance from the controls should be reported.C 1087 00 (2006)3FIG. 5 ASTM C1087 Compatibility Test Report FormC 1087 00 (2006)4ASTM International takes no position respec

37、ting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This sta

38、ndard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Internati

39、onal Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below

40、.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (f

41、ax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 2 Precision SummarySpecific Evaluation I(r) I(R)Color change, glass side up 0.803 2.166Color change, glass side down 0.782 1.826% cohesive failure of sealant to glass,glass side up21.88 % 39.08 % cohesive failure of sealant to glass,glass side down19.00 % 21.75 % cohesive failure of sealant to accessory,glass side up4.75 % 28.08 % cohesive failure of sealant to accessory,glass side down17.00 % 36.46 %C 1087 00 (2006)5