ASTM C1014-2008 Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation《喷施的矿物纤维吸热和吸音绝缘材料标准规范》.pdf
《ASTM C1014-2008 Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation《喷施的矿物纤维吸热和吸音绝缘材料标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM C1014-2008 Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation《喷施的矿物纤维吸热和吸音绝缘材料标准规范》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: C 1014 08Standard Specification forSpray-Applied Mineral Fiber Thermal and Sound AbsorbingInsulation1This standard is issued under the fixed designation C 1014; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year
2、of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the composition and the physi-cal properties of spray-applied mineral fiber thermal and
3、soundabsorbing insulation.1.2 These mineral fibers shall be pneumatically conveyed toa spray nozzle where they are mixed with water. These mineralfibers shall have a binder either pre-mixed with the fibers oradded at the spray nozzle with the water.1.3 The spray-applied mineral fiber insulation is i
4、ntendedfor use in building constructions at ambient conditions.1.4 This is a material specification only and is not intendedto cover methods of application that are supplied by themanufacturer.1.5 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses ar
5、e mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety
6、and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C 168 Terminology Relating to Thermal InsulationC 177 Test Method for Steady-State Heat Flux Measure-ments and Thermal Transmission Properties by Means ofthe Guarde
7、d-Hot-Plate ApparatusC 390 Practice for Sampling and Acceptance of ThermalInsulation LotsC 423 Test Method for Sound Absorption and Sound Ab-sorption Coefficients by the Reverberation Room MethodC 518 Test Method for Steady-State Thermal TransmissionProperties by Means of the Heat Flow Meter Apparat
8、usC 665 Specification for Mineral-Fiber Blanket Thermal In-sulation for Light Frame Construction and ManufacturedHousingC 1104/C 1104M Test Method for Determining the WaterVapor Sorption of Unfaced Mineral Fiber InsulationC 1114 Test Method for Steady-State Thermal TransmissionProperties by Means of
9、 the Thin-Heater ApparatusC 1149 Specification for Self-Supported SprayApplied Cel-lulosic Thermal InsulationC 1304 Test Method for Assessing the Odor Emission ofThermal Insulation MaterialsC 1338 Test Method for Determining Fungi Resistance ofInsulation Materials and FacingsC 1368 Test Method for D
10、etermination of Slow CrackGrowth Parameters of Advanced Ceramics by ConstantStress-Rate Flexural Testing at Ambient TemperatureE84 Test Method for Surface Burning Characteristics ofBuilding MaterialsE 605 Test Methods for Thickness and Density of SprayedFire-Resistive Material (SFRM) Applied to Stru
11、cturalMembersE 756 Test Method for Measuring Vibration-Damping Prop-erties of MaterialsE 759 Test Method for Effect of Deflection on SprayedFire-Resistive Material Applied to Structural MembersE 795 Practices for Mounting Test Specimens DuringSound Absorption TestsE 859 Test Method for Air Erosion o
12、f Sprayed Fire-Resistive Materials (SFRMs) Applied to Structural Mem-bers3. Terminology3.1 DefinitionsFor definitions of terms used in this speci-fication, see Terminology C 168.3.2 Definitions of Terms Specific to This Standard:3.2.1 constant massthe mass of a sample at equilibriumconditions of 75
13、6 5F (23 6 5C) and 50 6 5 % relativehumidity that shall not deviate more than 0.5 % over a 24-hperiod.1This specification is under the jurisdiction of ASTM Committee C16 onThermal Insulation and is the direct responsibility of Subcommittee C16.23 onBlanket and Loose Fill Insulation.Current edition a
14、pproved March 1, 2008. Published April 2008. Originallyapproved in 1984. Last previous edition approved in 2003 as C 101403e1.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information,
15、 refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.2.2 curedthe state or condition of the finished productafter the liquid vehicle has been evaporated to a constant mass
16、.4. Materials and Manufacture4.1 CompositionThe basic material shall be fibers madeform mineral substances such as rock, slag or glass processedfrom the molten state into a fibrous form. If necessary, addorganic or inorganic substances to the fibers or to the binder, orto both, to enhance properties
17、 such as flame retardancy,processing, and adhesive/cohesive properties.5. Physical Properties5.1 For spray-applied mineral fiber insulation, the propertiesof density, thermal resistance, and sound absorption will varywith the manufacturer. These values shall be as stated by themanufacturer before sa
18、le and shall be tested in accordance with9.1, 9.3, and 9.10, respectively.5.1.1 Test SpecimensThree specimens shall be tested,unless otherwise agreed upon between purchaser and supplier.These are to be obtained from one representative package ofinsulation.5.2 Adhesive/Cohesive (Bond Strength)All sel
19、f-supporting applications of the insulation shall have a minimumadhesive/cohesive strength of five times the weight of thematerial under the testing plate when tested in accordance with9.2.5.3 Substrate DeflectionThe insulation shall not spall,crack, or delaminate when the substrate is deflected an
20、equiva-lent of1120 th the span when tested in accordance with 9.4.5.4 Water Vapor SorptionThe insulation shall gain notmore than 5 % moisture by weight when tested in accordancewith 9.5.5.5 Surface Burning CharacteristicsThe insulation shallhave a maximum flame spread index of 25 and a maximumsmoke
21、developed of 50 when tested in accordance with 9.6.5.6 Smoldering CombustionThe insulation shall have aweight loss not greater than 5 %, nor shall there be a flamingignition when tested in accordance with 9.7.5.7 Fungi ResistanceWhen tested in accordance with 9.8the insulation shall have growth no g
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMC10142008STANDARDSPECIFICATIONFORSPRAYAPPLIEDMINERALFIBERTHERMALANDSOUNDABSORBINGINSULATION 喷施 矿物纤维

链接地址:http://www.mydoc123.com/p-463055.html