ASTM B950-2011a Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys《铜和铜合金产品的说明书编辑程序及形式的标准指南》.pdf

《ASTM B950-2011a Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys《铜和铜合金产品的说明书编辑程序及形式的标准指南》.pdf》由会员分享，可在线阅读，更多相关《ASTM B950-2011a Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys《铜和铜合金产品的说明书编辑程序及形式的标准指南》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B950 11aStandard Guide forEditorial Procedures and Form of Product Specifications forCopper and Copper Alloys1This standard is issued under the fixed designation B950; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, th

2、e year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This guide covers the editorial procedures and form andstyle for product specifications under the jurisdict

3、ion of ASTMCommittee B05 on Copper and Copper Alloys.NOTE 1For standards other than product specifications, such as testmethods, practices, and guides, see the appropriate sections of Form andStyle for ASTM Standards (Blue Book).21.2 This guide has been prepared as a supplement to thecurrent edition

4、 of the Form and Style Manual, and is appro-priate for use by the subcommittees within ASTM CommitteeB05 on Copper and Copper Alloys. This guide is to be appliedin conjunction with the Form and Style Manual. The Appendixcontains a copy of the B05 electronic template which includesadopted language fo

5、r various sections and provides a templatefor drafting B05 product specifications.NOTE 2The contents of this guide were previously maintained as awhite paper under the title, “ASTM Committee B05 Outline of Form ofSpecifications.”1.3 Subcommittees preparing new product specifications orrevising exist

6、ing ones should follow the practices and proce-dures outlined herein, and be guided by the latest specificationscovering similar commodities.1.4 If a conflict exists between this guide and the mandatorysections of the current edition of the Form and Style Manual,the Form and Style Manual requirement

7、s have precedence. If aconflict exists between this guide and the nonmandatorysections of the current edition of the Form and Style Manual,the guide has precedence.1.5 When patents are involved, the specifications writershould refer to the Form and Style Manual section on patentsand trademarks. Also

8、, refer to part F of the Form and StyleManual for trademark information and the safety hazardscaveat.2. Referenced Documents2.1 ASTM Standards:3B75 Specification for Seamless Copper TubeB153 Test Method for Expansion (Pin Test) of Copper andCopper-Alloy Pipe and TubingB154 Test Method for Mercurous

9、Nitrate Test for CopperAlloysB170 Specification for Oxygen-Free Electrolytic CopperRefinery ShapesB193 Test Method for Resistivity of Electrical ConductorMaterialsB194 Specification for Copper-Beryllium Alloy Plate,Sheet, Strip, and Rolled BarB216 Specification for Tough-Pitch Fire-Refined CopperRef

10、inery ShapesB224 Classification of CoppersB248 Specification for General Requirements for WroughtCopper and Copper-Alloy Plate, Sheet, Strip, and RolledBarB248M Specification for General Requirements forWrought Copper and Copper-Alloy Plate, Sheet, Strip, andRolled Bar (Metric)B249/B249M Specificati

11、on for General Requirements forWrought Copper and Copper-Alloy Rod, Bar, Shapes andForgingsB250/B250M Specification for General Requirements forWrought Copper Alloy WireB251 Specification for General Requirements for WroughtSeamless Copper and Copper-Alloy TubeB251M Specification for General Require

12、ments forWrought Seamless Copper and Copper-Alloy Tube (Met-ric)B577 Test Methods for Detection of Cuprous Oxide (Hy-drogen Embrittlement Susceptibility) in CopperB601 Classification for Temper Designations for Copperand Copper AlloysWrought and CastB824 Specification for General Requirements for Co

13、pperAlloy Castings1This guide is under the jurisdiction of ASTM Committee B05 on Copper andCopper Alloys and is the direct responsibility of Subcommittee B05.91 on Editorialand Publications.Current edition approved Oct. 1, 2011. Published November 2011. Originallyapproved in 2006. Last previous edit

14、ion approved in 2011 as B950 11. DOI:10.1520/B0950-11A.2Available from ASTM International Headquarters, 100 Barr Harbor Drive, POBox C700, West Conshohocken, PA 19428-2959.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For An

15、nual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.B846 Ter

16、minology for Copper and Copper AlloysB858 Test Method for Ammonia Vapor Test for Determin-ing Susceptibility to Stress Corrosion Cracking in CopperAlloysB900 Practice for Packaging of Copper and Copper AlloyMill Products for U.S. Government AgenciesB968/B968M Test Method for Flattening of Copper and

17、Copper-Alloy Pipe and TubeE6 Terminology Relating to Methods of Mechanical TestingE8/E8M Test Methods for Tension Testing of MetallicMaterialsE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specification

18、sE44 Definitions of Terms Related to Heat Treatment4E53 Test Method for Determination of Copper in UnalloyedCopper by GravimetryE54 Test Methods for ChemicalAnalysis of Special Brassesand Bronzes4E62 Test Methods for Chemical Analysis of Copper andCopper Alloys (Photometric Methods)4E76 Test Methods

19、 for Chemical Analysis of Nickel-CopperAlloys4E112 Test Methods for Determining Average Grain SizeE118 Test Methods for Chemical Analysis of Copper-Chromium Alloys4E121 Test Methods for Chemical Analysis of Copper-Tellurium Alloys4E243 Practice for Electromagnetic (Eddy-Current) Exami-nation of Copp

20、er and Copper-Alloy TubesE478 Test Methods for ChemicalAnalysis of CopperAlloysE527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)E581 Test Methods for Chemical Analysis of Manganese-Copper AlloysE1227 Terminology Relating to Chemical Analysis of Met-als4E1371 Test Met

21、hod for Gravimetric Determination of Phos-phorus in Phosphorus-Copper Alloys or Phosphorus-Copper-Silver Alloys42.2 Other ASTM Documents:5Form and Style for ASTM StandardsCommittee B05 Bylaws Appendix IIITerminology Man-agement Policy2.3 ISO Documents:6ISO 4744 Copper and copper alloys - Determinati

22、on ofchromium content - Flame atomic absorption spectromet-ric methodISO 76022.4 JIS Documents:JIS H1068 Methods for Determination of Bismuth in Cop-per and Copper Alloys3. Terminology3.1 For definitions of terms used in this guide, refer to theForm and Style Manual and Terminology B846.4. Significa

23、nce and Use4.1 The Form and Style for ASTM Standards manualprovides mandatory requirements and recommended practicesfor the preparation and content of ASTM specifications. Inorder to promote consistency in the style and content ofproduct specifications under its jurisdiction, Committee B05recognizes

24、 the need to provide a supplementary documentpertaining to the types of products and materials covered byspecifications under its jurisdiction.4.2 This guide contains a list of sections to be considered forinclusion in a specification for copper and copper alloys,recommended wording, or both, for su

25、ch sections. An elec-tronic template including committee adopted language isincluded in the Appendix.74.3 Persons drafting new product specifications, or modify-ing existing ones, under the jurisdiction of Committee B05,should follow this guide and the requirements of the Form andStyle Manual to ens

26、ure consistency.5. Subject Headings of Text5.1 The following is the heading sequence for the specifi-cations text. The headings listed are those most generally used.Other headings may be included for specialized subjects whenthe information is pertinent to the document under develop-ment; in which c

27、ase, all instructions and guidance for thatparticular section shall be applied, and these headings shouldappear in the most appropriate place and sequence dependingon their relationship to other sections.5.2 SuperscriptsThe headings identified as mandatory arerequired by the Society. The headings id

28、entified with anasterisk (*) are a guide for Committee B05 documents, whereapplicable, either by inclusion or by reference to a generalrequirements specification.5.3 Not all of the headings may be required for a particularstandard specification. For example, when the specificationdoes not contain re

29、ference to any other standard within the text,it is not required to include a section on Referenced Docu-ments. Or, in the case where no physical property requirementsare given, the physical property section is not required.TitleASTMSamplingB05DesignationASTMNumber of Tests and RetestsB05ScopeASTMSp

30、ecimen PreparationB05Referenced DocumentsB05Test MethodsB05*General RequirementsB05,ASignificance of Numerical LimitsB05TerminologyB05InspectionB05Classification Rejection and RehearingB05Ordering informationB05CertificationB05Materials and ManufactureB05Test ReportsB05Chemical CompositionB05Product

31、 MarkingTemperB05Packaging and Package MarkingB05Grain Size of Annealed Tempers KeywordsASTM4Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.5For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at servicea

32、stm.org.6Available from International Organization for Standardization (ISO), 1, ch. dela Voie-Creuse, Case postale 56, CH-1211, Geneva 20, Switzerland, http:/www.iso.ch.7See B05 Main Page on the ASTM website, www.astm.org, for an electronicWORD version of the template.B950 11a2Physical Property Req

33、uirementsB05Summary of ChangesB05Mechanical Property Requirements*Supplementary RequirementsPerformance Requirements Quality AssuranceOther Requirements AnnexesDimensions, Mass, and PermissibleVariationsB05AppendixesWorkmanship, Finish, andAppearanceB05ASTMMandatory ASTM Society requirementB05Guide

34、for B05 specificationsAWhen reference is made to a general requirements specification, the se-quence position of the General Requirements section in the product specifi-cation should be prior to the first section referenced, which is usually Termi-nology.BTest methods that are detailed in specificat

35、ions shall contain all of themandatory headings shown in Part A, Section A1, of the Blue Book.5.4 Subject Headings shall precede each section to orientthe reader. Section and text paragraphs shall be numbered inaccordance with the Guide for the Use of the ModifiedNumbering System in Part D of the Fo

36、rm and Style for ASTMStandards manual. The following is an example of how itshould appear in a standard:1. Scope1.1 This specification establishes the requirements for.etc.6. Section ContentsNOTE 3Explanations of section content requirements are detailed inthis section. In the Annex and published se

37、parately on the B05 Main Pageunder Additional Information, is an electronic template containing recom-mended language for each section. In this guide, the examples wereremoved to avoid redundancy and inconsistencies.6.1 TitleASTM6.1.1 The title should be as concise as possible, yet com-plete enough

38、to identify the material, product, system, orservices for which the requirements are established by thedocument.6.2 Designation and Year of IssueASTM6.2.1 DesignationThe alphanumeric designation is as-signed by ASTM Headquarters.6.2.2 Year DateAfter the designation, a hyphen is fol-lowed by the last

39、 two numbers of the year of acceptance or lastrevision. Reapprovals are the last date in parentheses. Footnote1 is not changed with a reapproval.NOTE 4The Form and Style Manual includes definitions of date ofissue and year date.6.3 ScopeASTM6.3.1 The Scope should be a brief summary of the productand

40、 product application.6.3.2 A statement shall be included in this section as towhether inch-pound or SI units are the standard, if thespecification has a companion specification or is a dualdesignation specification.6.3.3 Include the prescribed caveat on safety hazards permandatory blue book language

41、, when one or more test methodsare included other than by reference.NOTE 5The safety hazard caveat shall also appear in test methods,guides, and practices that involve the use of materials, operations, orequipment.6.3.4 Related documents not referenced in the text may beincluded as a footnote, or li

42、sted as References at the end of thestandard cited by number if more than five are cited.6.4 Referenced DocumentsB056.4.1 List in alphanumeric sequence the designation andcomplete title of all standards and other documents referenced,including standards and codes of other organizations.6.4.2 Provide

43、 footnotes to this section indicating the sourceof the documents. When referenced later in the text, us only thetype of document (specification, test method, practice, guide,etc.) and the designation letter and number (for example, TestMethods B577).6.4.3 Do not use the year of issue when listing th

44、e refer-enced documents unless there is a technical reason for requir-ing a specific issue.6.5 General RequirementsB05,A6.5.1 This section should be used for requirements that areavailable in a General Requirements specification and areincluded in the specification by reference. General Require-ment

45、s specifications are B248, B248M, B249/B249M, B250/B250M, B251, B251M, and B824. When a product specifica-tion refers to a general requirements specification forapplicable requirements, the reference shall be made in thissection so as to alert the user that the details of the require-ment(s) shall b

46、e found in another document.6.5.1.1 The utilization of a general requirements section inthe drafting of a new specification or in the revision of astandard is not mandatory; however, it is recommended sinceconsiderable repetition within a group of similar documentswould be avoided.6.5.1.2 In the cas

47、e where a section in the general require-ments section has been referenced and the same titled sectionappears in the product specification with requirements thateither supplement or supersede the referenced general require-ments section, use the explanatory clause 3.2 in the electronictemplate.6.6 T

48、erminologyB05NOTE 6For use of terminology in B05 standards, refer also to theCommittee B05 Terminology Management Policy.6.6.1 When applicable, refer to Terminology B846 fordefinitions of terms relating to copper and copper alloys, or toother existing ASTM terminology standards having generalapplica

49、tions. Terms not appearing in other ASTM terminologystandards and requiring other than dictionary definitions shouldbe defined.6.6.1.1 Examples of ASTM terminology standards havinggeneral application are: E44, Definitions of Terms Relating toHeat Treatment; E6, Definition of Terms Relating to Mechani-cal Testing; E1227 Terminology Relating to ChemicalAnalysisof Metals.6.6.2 Definitions:6.6.2.1 Definitions shall be in dictionary-definition form,following the guidelines of Part E of The Form and StyleManual and, when appropriate, include in this section defini-tions f