ASTM B950-2006 Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys《铜和铜合金产品规范的编辑程序和格式的标准指南》.pdf

《ASTM B950-2006 Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys《铜和铜合金产品规范的编辑程序和格式的标准指南》.pdf》由会员分享，可在线阅读，更多相关《ASTM B950-2006 Standard Guide for Editorial Procedures and Form of Product Specifications for Copper and Copper Alloys《铜和铜合金产品规范的编辑程序和格式的标准指南》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B 950 06Standard Guide forEditorial Procedures and Form of Product Specifications forCopper and Copper Alloys1This standard is issued under the fixed designation B 950; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, t

2、he year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This guide covers the editorial procedures and form andstyle for product specifications under the jurisdi

3、ction of ASTMCommittee B05 on Copper and Copper Alloys.NOTE 1For standards other than product specifications, such as testmethods, practices, and guides, see the appropriate sections of Form andStyle for ASTM Standards (Blue Book).21.2 This guide has been prepared as a supplement to thecurrent editi

4、on of the Form and Style Manual, and is appro-priate for use by the subcommittees within ASTM CommitteeB05 on Copper and Copper Alloys. This guide is to be appliedin conjunction with the Form and Style Manual. The Appendixcontains a copy of the B05 electronic template which includesadopted language

5、for various sections and provides a templatefor drafting B05 specifications.NOTE 2The contents of this guide were previously maintained as awhite paper under the title, “ASTM Committee B05 Outline of Form ofSpecifications.”1.3 Subcommittees preparing new product specifications orrevising existing on

6、es should follow the practices and proce-dures outlined herein, and be guided by the latest specificationscovering similar commodities.1.4 If a conflict exists between this guide and the mandatorysections of the current edition of the Form and Style Manual,the Form and Style Manual requirements have

7、 precedence. If aconflict exists between this guide and the nonmandatorysections of the current edition of the Form and Style Manual,the guide has precedence.1.5 When patents are involved, the specifications writershould refer to the Form and Style Manual section on patentsand trademarks. Also, refe

8、r to part F of the Form and StyleManual for trademark information and the safety hazardscaveat.2. Referenced Documents2.1 ASTM Standards:3E75 Test Methods for Chemical Analysis of Copper-Nickeland Copper-Nickel-Zinc AlloysB 170 Specification for Oxygen-Free Electrolytic CopperRefinery ShapesB 194 Sp

9、ecification for Copper-Beryllium Alloy Plate,Sheet, Strip, and Rolled BarB 216 Specification for Tough-Pitch Fire-Refined CopperRefinery ShapesB 224 Classification of CoppersB 248 Specification for General Requirements for WroughtCopper and Copper-Alloy Plate, Sheet, Strip, and RolledBarB 248 Specif

10、ication for General Requirements for WroughtCopper and Copper-Alloy Plate, Sheet, Strip, and RolledBarB 249/B 249M Specification for General Requirements forWrought Copper and Copper-Alloy Rod, Bar, Shapes andForgingsB 250/B 250M Specification for General Requirements forWrought Copper Alloy WireB 2

11、51 Specification for General Requirements for WroughtSeamless Copper and Copper-Alloy TubeB 577 Test Methods for Detection of Cuprous Oxide (Hy-drogen Embrittlement Susceptibility) in CopperB 601 Classification for Temper Designations for Copperand Copper AlloysWrought and CastB 824 Specification fo

12、r General Requirements for CopperAlloy CastingsB 846 Terminology for Copper and Copper AlloysE6 Terminology Relating to Methods of Mechanical Test-ingE44Definitions of Terms Related to Heat Treatment4E53 Test Method for Determination of Copper in Unal-loyed Copper by Gravimetry1This guide is under t

13、he jurisdiction of ASTM Committee B05 on Copper andCopper Alloys and is the direct responsibility of Subcommittee B05.91 on Editorialand Publications.Current edition approved Oct. 1, 2006. Published December 2006.2Available from ASTM International Headquarters, 100 Barr Harbor Drive, POBox C700, Wes

14、t Conshohocken, PA 19428-2959.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section

15、appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.E54 Test Methods for Chemical Analysis of SpecialBrasses and Bronzes4E62 Test Methods for Chemical Analysis of Copper andCopper Alloys (Photometric Me

16、thods)E 75 Test Methods for Chemical Analysis of Copper-Nickeland Copper-Nickel-Zinc AlloysE76 Test Methods for ChemicalAnalysis of Nickel-CopperAlloys4E118 Test Methods for Chemical Analysis of Copper-Chromium AlloysE 121 Test Methods for Chemical Analysis of Copper-Tellurium AlloysE 478 Test Metho

17、ds for Chemical Analysis of CopperAlloysE 1227 Terminology Relating to Chemical Analysis ofMetals4E 1371 Test Method for Gravimetric Determination ofPhosphorus in Phosphorus-Copper Alloys or Phosphorus-Copper-Silver Alloys42.2 Other ASTM Documents:5Form and Style for ASTM StandardsCommittee B05 Byla

18、ws Appendix IIITerminology Man-agement Policy2.3 ISO Documents:6ISO 4744 Copper and copper alloys - Determination ofchromium content - Flame atomic absorption spectromet-ric methodISO 76023. Terminology3.1 For definitions of terms used in this guide, refer to theForm and Style Manual and Terminology

19、 B 846.4. Significance and Use4.1 The Form and Style for ASTM Standards manualprovides mandatory requirements and recommended practicesfor the preparation and content of ASTM specifications. Inorder to promote consistency in the style and content ofproduct specifications under its jurisdiction, Comm

20、ittee B05recognizes the need to provide a supplementary documentpertaining to the types of products and materials covered byspecifications under its jurisdiction.4.2 This guide contains a list of sections to be considered forinclusion in a specification for copper and copper alloys,recommended wordi

21、ng, or both, for such sections. An elec-tronic template including committee adopted language isincluded in the Appendix.4.3 Persons drafting new product specifications, or modify-ing existing ones, under the jurisdiction of Committee B05,should follow this guide and the requirements of the Form andS

22、tyle Manual to ensure consistency.5. Subject Headings of Text5.1 The following is the heading sequence for the specifi-cations text. The headings listed are those most generally used.Other headings may be included for specialized subjects whenthe information is pertinent to the document under develo

23、p-ment; in which case, all instructions and guidance for thatparticular section shall be applied, and these headings shouldappear in the most appropriate place and sequence dependingon their relationship to other sections.5.2 SuperscriptsThe headings identified as mandatory arerequired by the Societ

24、y. The headings identified with anasterisk (*) are guide for Committee B05 documents, whereapplicable, either by inclusion or by reference to a generalrequirements specification.5.3 Not all of the headings may be required for a particularstandard specification. For example, when the specificationdoe

25、s not contain reference to any other standard within the text,it is not required to include a section on Referenced Docu-ments. Or, in the case where no physical property requirementsare given, the physical property section is not required.TitleASTMSamplingB05DesignationASTMNumber of Tests and Retes

26、tsB05ScopeASTMSpecimen PreparationB05Referenced DocumentsB05Test MethodsB05*General RequirementsB05,ASignificance of Numerical LimitsB05TerminologyB05InspectionB05Classification Rejection and RehearingB05Ordering informationB05CertificationB05Materials and ManufactureB05Test ReportsB05Chemical Compo

27、sitionB05Product MarkingTemperB05Packaging and Package MarkingB05Grain Size of Annealed Tempers KeywordsASTMPhysical Property RequirementsB05Summary of ChangesB05Mechanical Property Requirements*Supplementary RequirementsPerformance Requirements Quality AssuranceOther Requirements AnnexesDimensions,

28、 Mass, and PermissibleVariationsB05AppendixesWorkmanship, Finish, andAppearanceB05ASTMMandatory ASTM Society requirementB05Guide for B05 specificationsAWhen reference is made to a general requirements specification, the se-quence position of the General Requirements section in the product specifi-ca

29、tion should be prior to the first section referenced, which is usually Termi-nology.BTest methods that are detailed in specifications shall contain all of themandatory headings shown in Part A, Section A1, of the Blue Book.5.4 Subject Headings shall precede each section to orientthe reader. Section

30、and text paragraphs shall be numbered inaccordance with the Guide for the Use of the ModifiedNumbering System in Part D of the Form and Style for ASTMStandards manual. The following is an example of how itshould appear in a standard:1. Scope1.1 This specification establishes the requirements for.etc

31、.6. Section ContentsNOTE 3Explanations of section content requirements are detailed inthis section. In the Annex and published separately on the B05 web page,is an electronic template containing recommended language for eachsection. In this guide, the examples were removed to avoid redundancyand inc

32、onsistencies.4Withdrawn.5For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org.6B9500626.1 TitleASTM6.1.1 The title should be as concise as possible, yet com-plete enough to identify the material, product, system, orservices for which

33、 the requirements are established by thedocument.6.2 Designation and Year of IssueASTM6.2.1 DesignationThe alphanumeric designation is as-signed by ASTM Headquarters.6.2.2 Year DateAfter the designation, a hyphen is fol-lowed by the last two numbers of the year of acceptance or lastrevision. Reappro

34、vals are the last date in parentheses. Footnote1 is not changed with a reapproval.NOTE 4The Form and Style Manual includes definitions of date ofissue and year date.6.3 ScopeASTM6.3.1 The Scope should be a brief summary of the productand product application.6.3.2 A statement shall be included in thi

35、s section as towhether inch-pound or SI units are the standard, if thespecification has a companion specification or is a dualdesignation specification.6.3.3 Include the prescribed caveat on safety hazards permandatory blue book language, when one or more test methodsare included other than by refer

36、ence.NOTE 5The safety hazard caveat shall also appear in test methods,guides, and practices that involve the use of materials, operations, orequipment.6.3.4 Related documents not referenced in the text may beincluded as a footnote, or listed as References at the end of thestandard cited by number if

37、 more than five are cited.6.4 Referenced DocumentsB056.4.1 List in alphanumeric sequence the designation andcomplete title of all standards and other documents referenced,including standards and codes of other organizations.6.4.2 Provide footnotes to this section indicating the sourceof the document

38、s. When referenced later in the text, us only thetype of document (specification, test method, practice, guide,etc.) and the designation letter and number (for example, TestMethods B 577).6.4.3 Do not use the year of issue when listing the refer-enced documents unless there is a technical reason for

39、 requir-ing a specific issue.6.5 General RequirementsB05,A6.5.1 This section should be used for requirements that areavailable in a General Requirements specification and areincluded in the specification by reference. When a productspecification refers to a general requirements specification forappl

40、icable requirements, the reference shall be made in thissection so as to alert the user that the details of the require-ment(s) shall be found in another document.6.5.1.1 The utilization of a general requirements section inthe drafting of a new specification or in the revision of astandard is not ma

41、ndatory; however, it is recommended sinceconsiderable repetition within a group of similar documentswould be avoided.6.5.1.2 In the case where a section in the general require-ments section has been referenced and the same titled sectionappears in the product specification with requirements thateith

42、er supplement or supersede the referenced general require-ments section, use the explanatory clause 3.2 in the electronictemplate.6.6 TerminologyB05NOTE 6For use of terminology in B05 standards, refer also to theCommittee B05 Terminology Management Policy.6.6.1 When applicable, refer to Terminology

43、B 846 fordefinitions of terms relating to copper and copper alloys, or toother existing ASTM terminology standards having generalapplications. Terms not appearing in other ASTM terminologystandards and requiring other than dictionary definitions shouldbe defined.6.6.1.1 Examples of ASTM terminology

44、standards havinggeneral application are: E44, Definitions of Terms Relating toHeat Treatment; E6, Definition of Terms Relating to Mechani-cal Testing; E 1227 Terminology Relating to Chemical Analy-sis of Metals.6.6.2 Definitions:6.6.2.1 Definitions shall be in dictionary-definition form,following th

45、e guidelines of Part E of The Form and StyleManual and, when appropriate, include in this section defini-tions from any applicable terminology standard. The generalrequirements specifications B 248, B 249, B 250, B 251, andB 824 are examples of specifications incorporating definitions.6.6.3 Definiti

46、ons of Terms Specific to this Standard:6.6.3.1 Terms that are specific to the standard under devel-opment or revision shall appear in the Terminology sectionunder this heading.6.7 Classification6.7.1 When more than one material, product or system isspecified, each may be separated by type, and desig

47、nated byRoman numerals. The first subdivision shall be based uponsome major property, composition, or application of theproduct. Designate further subdivisions by grades according topertinent property or properties and identify by Arabic num-bers. When necessary, make additional divisions into class

48、esidentified by capital letters.6.7.1.1 An example of a classification standard is B 224.6.7.1.2 An example of material subdivided by grade isfound in the Table of Chemical Composition of SpecificationB 170.6.8 Ordering InformationB056.8.1 This section shall appear in all product specificationsas a

49、checklist of items which should be included in an inquiry,contract, or purchase order.6.8.2 When the specification provides choices for purchase,such as various types, grades, classes, materials, or tests, theinquiry, contract, or purchase order should state which particu-lar types, grades, classes, materials, sizes, tests, etc., arerequired.6.8.3 Alisting of each such choice, together with a referenceto the applicable section of the specification, will be ofassistance in the wording of the inquiry, contract, or purchaseorder. This list should include the ASTM specificat