ASTM B943-2005 Standard Specification for Zinc and Tin Alloy Wire Used in Thermal Spraying for Electronic Applications《电子设备热喷涂用锌和锌合金线的标准规范》.pdf

《ASTM B943-2005 Standard Specification for Zinc and Tin Alloy Wire Used in Thermal Spraying for Electronic Applications《电子设备热喷涂用锌和锌合金线的标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM B943-2005 Standard Specification for Zinc and Tin Alloy Wire Used in Thermal Spraying for Electronic Applications《电子设备热喷涂用锌和锌合金线的标准规范》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B 943 05Standard Specification forZinc and Tin Alloy Wire Used in Thermal Spraying forElectronic Applications1This standard is issued under the fixed designation B 943; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, t

2、he year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers zinc and tin alloy wire, includ-ing zinc-aluminum, zinc-aluminum-copper, zinc-ti

3、n, zinc-tin-copper and tin-zinc, used as thermal spray wire in the elec-tronics industry.1.1.1 Certain alloys specified in this standard are also usedas solders for the purpose of joining together two or moremetals at temperatures below their melting points, and for otherpurposes (as noted in Annex

4、A1). Specification B 907 coversZinc, Tin and Cadmium BaseAlloys Used as Solders which areused primarily for the purpose of joining together two or moremetals at temperatures below their melting points and for otherpurposes (as noted in the Annex part of Specification B 907).Specification B 833 cover

5、s Zinc and Zinc Alloy Wire forThermal Spraying (Metallizing) used primarily for the corro-sion protection of steel (as noted in the Annex part ofSpecification B 833).1.1.2 Tin base alloys are included in this specificationbecause their use in the electronics industry is similar to the useof certain

6、zinc alloys but different than the major use of the tinand lead solder compositions specified in Specification B32.1.1.3 These wire alloys have a nominal liquidus temperaturenot exceeding 850F (455C).1.2 The values stated in inch-pound units are to be regardedas the standard. The values given in par

7、entheses are forinformation only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (

8、MSDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B32 Specification for Solder MetalB 833 Specification for Zinc and Zin

9、c Alloy Wire forThermal Spraying (Metallizing)B 899 Terminology Relating to Non-ferrous Metals andAlloysB 907 Specification for Zinc, Tin and Cadmium Base Al-loys Used as SoldersE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE46 Test Methods for Che

10、mical Analysis of Lead andTin-Base Solder3E47 Test Methods for Chemical Analysis of Zinc Die-Casting Alloys3E51 Method for Spectrographic Analysis of Tin Alloys bythe Powder Technique3E87 Methods for Chemical Analysis of Lead, Tin, Anti-mony, and Their Alloys (Photometry Method)3E 527 Practice for N

11、umbering Metals and Alloys (UNS)E 536 Test Methods for ChemicalAnalysis of Zinc and ZincAlloys2.2 Federal Standard:Fed. Std. No. 123 Marking for Shipment (Civil Agencies)42.3 Military Standard:MIL-STD-129 Marking for Shipment and Storage43. Terminology3.1 Terms shall be defined in accordance with Te

12、rminologyB 899.1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.04 on Zinc and Cadmium.Current edition approved Nov. 1, 2005. Published December 2005.2For referenced ASTM standards, visit the ASTM w

13、ebsite, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave.,

14、 Philadelphia, PA 19111-5098.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4. Classification4.1 Type DesignationThe type designation uses the fol-lowing symbols to properly identify the material:4.1.1 Alloy CompositionThe compositi

15、on is identified bya two or four-letter symbol and a number. The letters typicallyindicate the chemical symbol for the critical element(s) in thewire and the number indicates the nominal percentage, byweight, of the primary element in the wire (see Table 1).5. Ordering Information5.1 Orders for mate

16、rial under this specification indicate thefollowing information, as required, to adequately describe thedesired material.5.1.1 Type designation (see 4.1),5.1.2 Detailed requirements for special forms,5.1.3 Dimensions of wire (see 9.2),5.1.4 Unit weight,5.1.5 Packaging (see Section 17),5.1.6 Marking

17、(see Section 16),5.1.7 ASTM Specification number and issue, marked on (a)purchase order and (b) package or spool, and5.1.8 Special requirements, as agreed upon between sup-plier and purchaser.6. Materials and Manufacture6.1 The producer shall have each lot of wire as uniform inquality as practicable

18、 and of satisfactory appearance in accor-dance with best industrial practices.7. Chemical Composition7.1 The wire shall conform to the requirements prescribedin Table 1.7.2 The manufacturer shall perform chemical analyses asdirected in Test Methods E 536 or by other methods of at leastequal accuracy

19、 to confirm that the wire conforms to therequirements of composition. In case of dispute, analysis byTest Methods E 536 shall be accepted. Analysis of alloy wiresnot covered by Test Methods E 536 shall be agreed uponbetween the manufacturer and the purchaser.NOTE 1By mutual agreement between supplie

20、r and purchaser, analy-sis may be required and limits established for elements or compounds notspecified in Table 1.8. Dimensions and Unit Weight8.1 The dimensions and unit weight of wire are specified in5.1.3 and 5.1.4. The tolerance on specified outside diametershall be 65%or60.002 in. (0.05 mm),

21、whichever is greater.9. Workmanship, Finish and Appearance9.1 The wire shall be clean and free of corrosion, adheringforeign material, scale, seams, nicks, burrs, and other defectswhich would interfere with the operation of thermal sprayingequipment. The wire shall uncoil readily and be free of bend

22、sor kinks that would prevent its passage through the thermalspray gun.9.2 The wire shall be a continuous length per spool, coil, ordrum. Splices or welds are permitted, provided that they do notinterfere with the thermal spray equipment or coating process.9.3 The starting end of each coil shall be t

23、agged to indicatewinding direction and to be readily identifiable with ASTMdesignation.10. Sampling10.1 Sampling methodology should ensure that the sampleselected for testing is representative of the material. Themethod for sampling consists of one of the following methods:10.1.1 Analysis may be per

24、formed on finished wire, onmaterial selected when the wire is cast, or on samples takenfrom semi-finished wire.10.1.1.1 If the analysis is performed on finished wire, thefrequency of sampling for determination of chemical compo-sition shall be in accordance with Table 2. For spools and coils,TABLE 1

25、 Zinc and Zinc Alloy Wire CompositionsComposition %A,B,CTemperatureFCFC UNSDCd Zn Sn Pb Sb Ag Cu Al Bi As Fe Ni Mg Solidus LiquidusZn 98 Z30402 0.005 REM 0.003 0.005 0.10 0.015 0.005 1.52.5 0.02 0.002 0.02 0.005 0.02 720 382 770 410Zn 96 XXXXE0.005 REM 0.003 0.005 0.10 0.015 0.005 3.54.5 0.02 0.002

26、0.02 0.005 0.02 720 382 720 382Zn 95 Z30502 0.005 REM 0.003 0.005 0.10 0.015 0.005 4.55.5 0.02 0.002 0.02 0.005 0.02 720 382 720 382Zn 94 XXXXE0.005 REM 0.003 0.005 0.10 0.015 1.31.5 3.54.5 0.02 0.002 0.02 0.005 0.02 730 388 734 390Zn 87 Z30705 0.005 REM 0.003 0.005 0.10 0.015 0.005 12.513.5 0.02 0.

27、002 0.05 0.005 0.02 720 382 815 435Zn 85 Z30702 0.005 REM 0.003 0.005 0.10 0.015 0.005 14.016.0 0.02 0.002 0.06 0.005 0.02 720 382 842 450Zn/Sn 50 Z56900 0.005 REM 49.051.0 0.05 0.10 0.015 0.005 0.100 0.02 0.002 0.02 0.005 0.02 388 198 680 360Zn/Sn 49 Z56930 0.005 REM 47.550.5 0.05 0.10 0.015 0.81.3

28、 0.100 0.02 0.002 0.02 0.005 0.05 392 200 592 311Sn/Zn 60 XXXXE0.005 REM 59.061.0 0.005 0.10 0.015 0.01 0.100 0.005 0.002 0.02 0.005 0.05 390 199 666 352Sn/Zn 70 XXXXE0.005 REM 69.071.0 0.005 0.10 0.015 0.01 0.100 0.005 0.002 0.02 0.005 0.05 390 199 601 316Sn/Zn 75 XXXXE0.004 REM 74.076.0 0.20 0.10

29、0.015 0.05 0.050 0.020 0.020 0.02 0.005 0.05 390 199 572 300Sn/Zn 80 XXXXE0.005 REM 79.081.0 0.05 0.10 0.015 0.01 0.100 0.005 0.002 0.02 0.005 0.05 390 199 536 280AFor purposes of acceptance and rejection, the observed value or calculated value obtained from analysis should be rounded to the nearest

30、 unit in the last right-handplace of figures, used in expressing the specified limit, in accordance with the rounding procedure prescribed in Practice E29.BAll values not given as a range are maximum values unless stated otherwise.CRemainder (REM) determined arithmetically by difference.DThe USN des

31、ignations were established in accordance with Practice E 527. The last digit of a UNS number differentiates between alloys of similar composition.EUNS numbers to be added when assigned.TABLE 2 Frequency of SamplingSize of Lot,lb (kg)Number of Samples(spools, coils, containers or pieces)Up to 1000 (4

32、50), incl 3Over 1000 to 10 000 (450 to 4500), incl 5Over 10 000 (4500) 10B943052the sample is obtained by cutting back 6 ft (1.8 m) of wire fromthe free end and then taking the next 6 ft for test. In otherforms, an equivalent sample is selected at random from thecontainer.10.1.1.2 If the analysis is

33、 performed on material selectedwhile the wire is being cast, at least one sample shall beselected for each source of molten metal.10.1.1.3 If the analysis is performed on samples taken fromsemi-finished product, at least one sample shall be analyzed foreach 4500 kg (10 000 lb) or fraction thereof.10

34、.2 The manufacturer shall determine the diameter of thewire at the end and the beginning of each continuous wire in aproduction pack, coil, or spool of wire. Each determinationshall be the result of at least three measurements.10.3 The buyer reserves the right to reject wire that, duringuse, is foun

35、d to be defective.11. Specimen Preparation11.1 Each sample of wire is prepared in accordance withSection 10 as applicable.12. Test Methods12.1 Visual and Dimensional Examination:12.1.1 The wire must be examined to verify that thedimensions, unit weight, and workmanship are in accordancewith the appl

36、icable requirements.12.2 Alloy CompositionIn case of dispute, the chemicalanalysis is made in accordance with Test Methods E46, E47(for tin only) Method E51, E87, and E 536.13. Inspection13.1 When specified in the purchase order or contract, thepurchaser shall be furnished certification that samples

37、 repre-senting each lot have been tested or inspected as directed in thisspecification and the requirements have been met. Whenspecified in the purchase order to contract, a report of the testresults shall be furnished.13.2 An inspection lot shall be defined as a collection ofmaterial of the same ki

38、nd that has been produced to the samespecification from the same heat by a single supplier at onetime under essentially identical conditions and that are submit-ted for acceptance or retest as a group.14. Rejection and Rehearing14.1 Material that fails to conform to the requirements ofthis specifica

39、tion may be rejected. Rejection must be reportedto the producer or supplier promptly and in writing. In case ofdissatisfaction with the results of the test, the producer orsupplier may make claim for a rehearing.15. Certification15.1 When specified in the purchase order or contract aproducers certif

40、ication must be furnished to the purchaser thatthe material was manufactured, sampled, tested, and inspectedin accordance with this specification and has been found tomeet the requirements. When specified in the purchase order orcontract, a report of the test results must be furnished.16. Product Ma

41、rking16.1 Each spool or container must be marked to show thespecification number, type designation, dimensions, and unitweight of wire or other form and lot number. The producersname or trademark must be marked on the spool or container.17. Packaging and Package Marking17.1 The material shall be sep

42、arated by size and preparedfor shipment in such a matter as to ensure acceptance bycommon carrier and to afford protection from the normalhazards of transport.17.2 Packaging materials for electric arc spray wire shall benonconductive.17.3 Size(s) of Packaging:17.3.1 Coil inside diameter may range fr

43、om 30 to 56 cm (12to 22 in.).17.3.2 Coil weight shall be approximately 20 to 25 kg (45 to55 lb).17.3.3 Production pack drums shall measure approximately56 cm (22 in.) in diameter and approximately 81 cm (32 in.)high. Each drum shall contain a continuous wire, which iscoiled around a central core.17.

44、3.4 Net weight per drum shall be 205 to 250 kg (450 to550 lb).17.3.5 When special preservation, packaging and packingrequirements are agreed upon between purchaser and supplier,marking for shipment of such material must be in accordancewith Fed. Std. No. 123 for civil agencies and MIL-STD-129 formil

45、itary agencies.17.4 Each shipping unit shall be legibly marked with thepurchase order number, size, gross, tare, net weights, and thename of the supplier. The specification number shall be shownwhen required.18. Keywords18.1 electronic applications; thermal spray; tin-zinc alloys;wire; zinc-aluminum

46、 alloys; zinc-aluminum-copper alloy;zinc-tin-copper alloy; zinc-tin alloyB943053SUPPLEMENTARY REQUIREMENTSThe following supplementary requirements apply for all agencies of the United States Governmentor only when specified by the purchaser as part of the purchase order or contract.S1. Responsibilit

47、y for InspectionS1.1 The producer or supplier shall be responsible for theperformance of all inspection requirements as specified herein.Except as otherwise specified in the contract or order, thesupplier may use his own or any other facilities suitable for theperformance of the inspection requireme

48、nts specified hereinunless disapproved by the purchaser. The purchaser retains theright to perform any of the inspections and tests set forth in thisspecification, where such inspections and tests are deemednecessary, to ensure that the supplies and services conform tothe prescribed requirements.ANN

49、EX(Mandatory Information)A1. INTENDED USEA1.1 Alloy Compositions:A1.1.1 Zn 98This is a high temperature, high strengthsolder for joining aluminum to aluminum and offers highcorrosion resistance.A1.1.2 Zn 96This zinc-aluminum solder is similar to Zn97 but with a slightly shorter temperature range.A1.1.3 Zn 95This zinc-aluminum eutectic solder is usedwhere temperature limitations are critical and in applicationswhere an extremely short melting range is required.A1.1.4 Zn 94This zinc-aluminum-copper solder has alower melting temperature than Zn 90.A1.1.5 Zn 87Th