ASTM B794-1997(2015) Standard Test Method for Durability Wear Testing of Separable Electrical Connector Systems Using Electrical Resistance Measurements《采用电阻测量的可拆式电气连接器系统耐磨损试验的标准试验.pdf

《ASTM B794-1997(2015) Standard Test Method for Durability Wear Testing of Separable Electrical Connector Systems Using Electrical Resistance Measurements《采用电阻测量的可拆式电气连接器系统耐磨损试验的标准试验.pdf》由会员分享，可在线阅读，更多相关《ASTM B794-1997(2015) Standard Test Method for Durability Wear Testing of Separable Electrical Connector Systems Using Electrical Resistance Measurements《采用电阻测量的可拆式电气连接器系统耐磨损试验的标准试验.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B794 97 (Reapproved 2015)Standard Test Method forDurability Wear Testing of Separable Electrical ConnectorSystems Using Electrical Resistance Measurements1This standard is issued under the fixed designation B794; the number immediately following the designation indicates the year oforig

2、inal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the effects of repeated insertionand wi

3、thdrawal of separable electrical connectors which areharmful to the electrical performance of the connector.1.2 This test method is limited to electrical connectorsdesigned for use in applications where the current through anyone connection in the connector does not exceed 5 A, andwhere the connecto

4、r may be separated a number of timesduring the life of the connector.1.3 This test method is limited to electrical connectorsintended for use in air ambients where the operating tempera-ture is less than 65C.1.4 The values stated in SI units are to be regarded asstandard. No other units of measureme

5、nt are included in thisstandard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (M

6、SDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B539 Test Methods for Measuring Resistance of ElectricalConnections (St

7、atic Contacts)2.2 Military Standard:3MIL-STD-1344A Test Methods for Electrical Connectors3. Summary of Test Method3.1 Sample connectors are wired for precision resistancemeasurements of each test contact. The samples are dividedinto two groups; then resistance measurements are made ofeach test conta

8、ct. The connectors in one group undergo anumber of insertion/withdrawal cycles appropriate for theparticular connector under test, and the resistances of theseconnectors are measured again. The connectors in the othergroup are not disturbed. All samples are subjected to anaccelerated aging test; the

9、n the resistances are measured again.All samples are separated (withdrawn), exposed to an acceler-ated aging test in the uninserted condition, removed from thetest, reinserted, and resistances measured again. The variousresistance measurements are compared to detect effects of thewear and aging on e

10、lectrical performance.4. Significance and Use4.1 Materials for electrical connector contacts must satisfy anumber of requirements in the areas of electrical, mechanical,and economic characteristics. The stability of electrical prop-erties is one of the most important of these characteristics.Wear of

11、 contact surfaces may adversely affect these electricalproperties, especially in designs where the contact surfaces arerelatively thin coatings. This test method provides a means tocompare various material systems on a basis relevant to theirapplication in electrical connector contacts.4.2 Repeated

12、insertion and withdrawal of a connector maycause wear or other mechanical damage to the electricalcontact surfaces, rendering those surfaces more susceptible toenvironmental degradation. This test method is intended todetect degradation of the electrical properties of the connectorby such processes.

13、4.3 This test method describes procedures for conductingwear and durability testing of electrical connectors; the proce-dures produce quantitative results. These results may be usedto compare the performance of different connector designs sothat meaningful design choices can be made. Such results ma

14、yalso be used to compare the performance of a connector to apreviously established standard to evaluate the quality of thesamples under test.1This test method is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.11 on Elec

15、trical Contact Test Methods.Current edition approved May 1, 2015. Published May 2015. Originallyapproved in 1988. Last previous edition approved in 2009 as B794 97 (2009).DOI: 10.1520/B0794-97R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at

16、 serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.Copyright A

17、STM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.4 The test results obtained from this test method arelimited in their applicability to connector combinations that areequivalent in design and manufacture to those actually tested.4.5 The user is

18、 cautioned that the conditions in this testshould be compared to the conditions that the connector willexperience in the intended application in order to determine therelevance of this test method to the particular needs of the user.For example, the environmental stress in this test method isless se

19、vere than certain industrial and marine environments andtherefore test results are not directly applicable to predict theperformance of product intended for use in such areas.4.6 It is recommended that this test method be used in oneof two ways. First, it may be used to evaluate and report theperfor

20、mance of a particular connector system. In such a case,it is appropriate to report the results in a table in the formatshown in Fig. 1 and to state “The results shown in the tablewere obtained for (insert connector designation or description)when tested in accordance with ASTM Standard B794,Method _

21、 , Procedure _ .” Second, it may be used to imposerequirements for acceptance of product. In this case, limits forthe values shown in Fig. 1 must be established prior to productacceptance testing. Such limits may be established by variousmethods such as by evaluation of product which is known to bea

22、cceptable or by application of appropriate experience. Theselimits must be documented in a manner that the entityperforming the product test can refer to the limits to determineif the test product conforms to such limits. A purchaser maywish to supply a table of limits and include on the purchaseord

23、er a statement similar to: “The product, when tested inaccordance with ASTM Standard B794, Method _ , Proce-dure _ , shall meet the limits in the supplied table.” This tablesupplied by the purchaser may set limits on all of the values inFig. 1, or only on a subset of those values that the purchaserd

24、eems adequate to ensure the performance of the product.5. Apparatus5.1 Environmental Test Chamber, capable of controlling thetest ambient in accordance with the sequence shown in Table 1.The test chamber shall be sufficiently large that each testsample shall be positioned with at least 100 mm separa

25、ting itfrom the nearest wall of the test chamber. The test chamberdesign and operation procedure shall conform to the require-ments contained in MIL-STD-1344A, Method 1002.2.5.2 An instrument is required for measuring resistance bythe four-wire method. This instrument shall operate within thelimits

26、on current and open-circuit voltage set forth in TestMethods B539, Test Method C. The instrument shall becapable of measuring a resistance less than 0.100 with aresolution of 0.0001 . For a resistance 0.100 or larger, theinstrument shall be capable of measuring it with a resolution of0.1 % of the re

27、sistance value.6. Sampling and Test Specimens6.1 Selection of Sample ConnectorsObtain sufficientsample connectors so that the electrical resistance of at least200 contacts contained in at least 20 separate connectors willbe measured in the test. Obtain sample connectors that arerepresentative of tho

28、se that will be used in the intendedapplication. Recognize that a connector consists of two halvesand both halves must be representative of the product to beused. In some cases one half will be a conductive area or padon a printed wiring-board surface, therefore printed wiringboards must be obtained

29、 that have representative conductivepads. Specifically, the conductive pads shall be manufacturedto the same requirements as those that will be required of partsto be used in the system application. These requirements willnormally cover the manufacturing process, thickness,composition, hardness, and

30、 roughness of both the finish coatingand of any underplating or undercoating. Protective treatments,if used, shall also be specified. For the purpose of connectortesting, such printed wiring boards are generally fabricatedwith appropriate circuitry to permit four-wire resistance mea-surements.6.2 Se

31、lection of Sample ContactsIn the case where thesamples are multicontact connectors and electrical measure-ments are performed only on a fraction of the total number ofFIG. 1 Sample Format for Reporting ResultsTABLE 1 Environmental Test SequenceNOTE 1Tolerance on temperature control is 2.Step Elapsed

32、 Time,hTemperature,CRelative Humidity,%1 02.5 ascending, 2565 92 32 2.55.5 65 92 33 5.58 descending, 6525 87 84 810.5 ascending, 2565 92 35 10.513.5 65 92 36 13.516 descending, 6525 87 87 1624 25 92 3B794 97 (2015)2contacts, the contacts measured shall be distributed throughoutthe field of contacts.

33、 Measure the corresponding contacts ineach sample connector.7. Conditioning7.1 An electrical measurement laboratory is required inwhich the ambient temperature is controlled to 23 6 5C andthe relative humidity is held below 60 %. This laboratory neednot be dedicated to this test program to the exclu

34、sion of otheruses so long as those other uses do not degrade the quality ofdata obtained on the connector test samples.8. Procedure8.1 Selection of Test MethodSelect a test method from thefollowing table which is appropriate for connector design andapplication.Method Number of InsertionsA5B10C25D5E

35、100F 200G 400H (number selected per agreementbetween producer and user)8.2 Sample Preparation:8.2.1 Assemble the connectors into mounting plates, guides,fixtures, racks, or similar apparatus if such apparatus isgenerally used in the actual application of the connector.Perform such assembly at the ti

36、me in the sample wiring processthat best simulates the typical manner in which the connectorsare assembled into a system.8.2.2 Wire samples for evaluation by this test method forelectrical resistance measurements before the two connectorhalves are plugged together. The wiring and resistance mea-suri

37、ng circuitry shall be of the four-wire type as described inTest Methods B539. Do the wiring in a manner that is typicalof the way the connector would be wired in service, andespecially in a manner that does not introduce unrealisticcontaminants or mechanical stresses on the connector. Do notperform

38、cleaning, lubrication, or other treatments of theconnector unless such treatments are specified by the connectormanufacturer or user as the required procedure for the appli-cation of the particular connector under test.8.2.3 Wire at least one reference resistor for resistancemeasurements in such a m

39、anner that its resistance may bemeasured using the same instrumentation and procedures as areused for the test contacts. It is suggested that this referenceresistor be a length of wire or a path on a printed wiring boardwith a resistance of the same order of magnitude as that oftypical test contacts

40、. Measure and record the resistance of thisreference resistor each time that the test contacts are measured.Expose this reference resistor to the same test environments asthe test contacts and generally treat the resistor in the samemanner as the test contacts.8.2.4 Label the connectors and individu

41、al contacts therein insuch a manner that each test contact is uniquely identified.Randomly select one half of the connectors (10 connectors if20 connectors is the total sample size) to undergo wear testing,and refer to these as the “wear test samples.” Insert the otherhalf of the connectors only onc

42、e at the beginning of the test andrefer to these as the “control samples.”8.3 Methods and Procedures for Resistance Measurements:8.3.1 Prepare data sheets such that all information shown inthe sample data sheet illustrated in Fig. 2 may be recorded foreach test contact.8.3.2 Perform all electrical m

43、easurements and wear tests inthe electrical measurements laboratory discussed in Section 7.Test samples must be allowed to come to equilibrium in thisambient for a minimum of 1 h before electrical measurementsor connector insertion/withdrawal operations begin. All con-nector insertion/withdrawal ope

44、rations are done with the con-nector disconnected from any power source.8.3.3 Perform all resistance measurements under dry-circuitconditions as specified in Test Methods B539, Test Method C.In addition, use a suitable method to cancel small potentialsthat may be present in the measurement circuit.

45、Suitablemethods are (1) measuring the resistance with the currentflowing one direction through the test contact, reversing thecurrent flow and remeasuring resistance, and averaging the tworesistance measurements; (2) measuring voltage drop acrossthe test contact with a constant d-c current flowing,

46、measuringvoltage across the contact with no impressed current, andsubtracting the second voltage from the first and using theFIG. 2 Sample Data SheetB794 97 (2015)3result to calculate resistance; or (3) measuring resistance usingan a-c method. The user shall select one method and use itthroughout th

47、e experiment.8.3.4 Make all resistance measurements in such a mannerthat the value is recorded with the resolution meeting thefollowing requirements: For contacts with a measured resis-tance less than 0.100 , record the resistance with a resolutionof 0.0001 or better. For contacts with resistance of

48、 0.100 or greater, record the resistance measurement with a resolutionof 0.1 % or better. If the resistance changes during themeasurement such that after about5sastable value of therequired resolution cannot be determined, record an estimateand note that the resistance is unstable.8.3.5 After each m

49、easurement of the reference resistor,compare the new measured value to the initial value. If thevalues differ by more than 2 %, check the calibration of theresistance measurement instrumentation. If repair orrecalibration, or both, of the instrumentation is required,discard any measurements of test contacts made since thepreceding measurement of the reference resistor and repeat themeasurements. If new measurements are not feasible, mark thesuspect measurements on the data sheets.8.3.6 If the measured resistance of a contact appearsu