ASTM B722-2006(2016) Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Seamless Pipe and Tube《镍铬钼钴钨铁硅合金 (UNS N06333) 无缝管的标准规格》.pdf

《ASTM B722-2006(2016) Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Seamless Pipe and Tube《镍铬钼钴钨铁硅合金 (UNS N06333) 无缝管的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B722-2006(2016) Standard Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Seamless Pipe and Tube《镍铬钼钴钨铁硅合金 (UNS N06333) 无缝管的标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B722 06 (Reapproved 2016)Standard Specification forNickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-SiliconAlloy (UNS N06333) Seamless Pipe and Tube1This standard is issued under the fixed designation B722; the number immediately following the designation indicates the year oforiginal ad

2、option or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers alloy N06333 in the form ofhot-finished and

3、cold-finished seamless pipe and tube intendedfor heat-resisting applications and general corrosive service.The general requirements for pipe and tube are covered inSpecification B829.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathemat

4、icalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards includin

5、g those identified in the appropriateSafety Data Sheet (SDS) for this product/material as providedby the manufacturer, to establish appropriate safety and healthpractices, and determine the applicability of regulatory limi-tations prior to use.2. Referenced Documents2.1 ASTM Standards:2B829 Specific

6、ation for General Requirements for Nickel andNickel Alloys Seamless Pipe and Tube3. General Requirement3.1 Material furnished under this specification shall con-form to the applicable requirements of Specification B829unless otherwise provided herein.4. Ordering Information4.1 It is the responsibili

7、ty of the purchaser to specify allrequirements that are necessary for material ordered under thisspecification. Examples of such requirements include but arenot limited to the following:4.1.1 Alloy name or UNS number.4.1.2 ASTM designation and year of issue.4.1.3 Quantity (feet or number of pieces).

8、4.1.4 Dimensions:4.1.4.1 Pipe size.4.1.4.2 Tube dimensions (outside or inside diameter andnominal wall thickness).4.1.4.3 Length (specific or random).4.1.5 Hydrostatic Test or Nondestructive Electric TestSpecify type of test (see 5.2).4.1.6 CertificationState if certification is required.4.1.7 Sampl

9、es for Product (Check) AnalysisState whethersamples for product (check) analysis should be furnished.4.1.8 Purchaser InspectionIf purchaser wishes to witnesstests or inspection of material at place of manufacture, thepurchase order must so state indicating which tests or inspec-tions are to be witne

10、ssed.5. Mechanical and Other Requirements5.1 Tension TestThe mechanical properties of the materialat room temperature shall conform to those shown in Table 1.The sampling and specimen preparation are covered in Speci-fication B829.5.2 Hydrostatic or Nondestructive Electric TestEach pipeor tube shall

11、 be subjected to either the hydrostatic test or to thenondestructive electric test. The type of test to be used shall beat the option of the manufacturer, unless otherwise specified inthe purchase order.6. Dimensions and Permissible Variations6.1 The requirements of Specification B829 will applyexce

12、pt for hot-finished pipe and tube dimensional requirementsshown in Table 2.7. Chemical Requirements7.1 The material shall conform to the requirements as tochemical composition specified in Table 3. One test is requiredfor each lot as defined in Specification B829.1This specification is under the jur

13、isdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and Their Alloys.Current edition approved June 1, 2016. Published June 2016. Originallyapproved in 1983. Last previous edition approved in 2011 as B722 0

14、6 (2011).DOI: 10.1520/B0722-06R16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes secti

15、on appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States17.2 If a product (check) analysis is performed by thepurchaser, the material shall conform to the product (check)analysis variations in Table 3 of S

16、pecification B829.8. Number of Tests8.1 Chemical AnalysisOne test per lot.8.2 Tension TestOne longitudinal tension test shall bemade on a specimen from a pipe or tube representing 1 % ofthe pipe or tube for each lot.8.3 Hydrostatic or Nondestructive Electric TestEachlength of pipe or tube.9. Test Me

17、thods9.1 Hydrostatic TestThe allowable fiber stress for hydro-static testing purposes shall be 17 500 psi.9.1.1 Any pipe or tube that shows leaks during hydrostatictesting shall be rejected, but any leaking areas may be cut outand the pipe or tube retested as above.9.2 Nondestructive Electric TestEa

18、ch pipe or tube shall beexamined with a nondestructive electric test as per prescribedin Specification B829.10. Keywords10.1 seamless pipe; seamless tube; UNS N06333TABLE 1 Mechanical PropertiesTensileStrength, minpsi (MPa)Yield Strength,0.2 % offset,min psi (MPa)Elongationin 2 in. or 50 mm,or 4D,mi

19、n. %HardnessA80 000 (551) 35 000 (241) 3075 to 95HRBAHardness values are informative only and not to be construed as the basis foracceptance.TABLE 2 Permissible Variations for Outside Diameter and Wall Thickness of Hot-Finished Pipe and TubeNOTE 1OvalityFor tube 5 in. (127 mm) and under in outside d

20、iameter the tolerance on the outside diameter applies for individual measurementsand includes ovality. For tube over 5 in. (127 mm) in outside diameter, the mean outside diameter shall conform to the permissible variations of this table,and individual measurements shall not exceed twice the permissi

21、ble variations of this table.Nominal Outside Diameter, in. (mm)Permissible VariationsOutside Diameter or InsideDiameter, in. (mm)% of Thickness ofSpecified Average Wall% of Thickness ofSpecified Minimum WallPlus Minus Plus Minus Plus Minus18 (3.2) to 112 (38), incl 0.015 (0.4) 0.031 (0.8) 12.5 12.5

22、28.5 0Over 112 (38.1) to 4 (102), incl 0.031 (0.8) 0.031 (0.8) 12.5 12.5 28.5 0Over 4 (102) to 8 (203), incl 0.062 (1.6) 0.031 (0.8) 12.5 12.5 28.5 0TABLE 3 Chemical RequirementsElementCompositionLimits, %Carbon 0.10 maxManganese 2.0 maxPhosphorus 0.03Sulfur 0.03Silicon 1.5 maxChromium 24.027.0Nicke

23、l 44.048.0Molybdenum 2.54.0Cobalt 2.54.0Tungsten 2.54.0IronAremainderAElement may be determined arithmetically by difference.B722 06 (2016)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this

24、standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years

25、 andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committe

26、e, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-

27、2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 06 (2016)3