ASTM B653 B653M-2011(2016) Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Welding Fittings《无缝和焊接的锆和锆合金焊接配件的标准规格》.pdf

《ASTM B653 B653M-2011(2016) Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Welding Fittings《无缝和焊接的锆和锆合金焊接配件的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B653 B653M-2011(2016) Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Welding Fittings《无缝和焊接的锆和锆合金焊接配件的标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B653/B653M 11 (Reapproved 2016)Standard Specification forSeamless and Welded Zirconium and Zirconium AlloyWelding Fittings1This standard is issued under the fixed designation B653/B653M; the number immediately following the designation indicates the yearof original adoption or, in the c

2、ase of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers fittings, factory made fromthree grades of zirconium and zircon

3、ium alloys. The termwelding fittings applies to butt-welding parts such as 45 and90 elbows, 180 returns, caps, tees, reducers, lap-joint stubends, and other types.1.2 The values stated in either inch-pound units or SI unitsare to be regarded separately as the standard. Within the text,the SI units a

4、re shown in brackets. The values stated in eachsystem are not exact equivalents; therefore, each system mustbe used independently of the other. Combining values from thetwo systems may result in nonconformance with the specifi-cation.1.3 This standard does not purport to address all of thesafety con

5、cerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B493 Specification for Zirconium and Z

6、irconium AlloyForgingsB523/B523M Specification for Seamless and Welded Zirco-nium and Zirconium Alloy TubesB550/B550M Specification for Zirconium and ZirconiumAlloy Bar and WireB551/B551M Specification for Zirconium and ZirconiumAlloy Strip, Sheet, and PlateB614 Practice for Descaling and Cleaning Z

7、irconium andZirconium Alloy SurfacesB658/B658M Specification for Seamless and Welded Zirco-nium and Zirconium Alloy Pipe2.2 ANSI Standards:B16.9 Wrought Steel Butt-Welding Fittings3B36.19 Stainless Steel Pipe32.3 Manufacturers Standardization Society of the Valve andFittings Industry Standards:SP-25

8、 Standard Marking System for Valves, Fittings,Flanges, and Unions4SP-43 Standard Practice for Light Weight Stainless SteelFittings42.4 American Society of Mechanical Engineers:ASME Boiler and Pressure Vessel Code, Sections VIII andIX53. Terminology3.1 Lot Definitions:3.1.1 weld fittings, ndefinition

9、 is to be mutually agreedupon between manufacturer and the purchaser.4. Classification4.1 The fittings are furnished in three grades as follows:4.1.1 Grade R60702 (PZ 2)Unalloyed zirconium.4.1.2 Grade R60704 (PZ 4)Zirconium-tin.4.1.3 Grade R60705 (PZ 5)Zirconium-niobium.5. Ordering Information5.1 Or

10、ders for materials under this specification shall in-clude the following information:5.1.1 Quantity,5.1.2 Name of material (zirconium fittings),5.1.3 Grade number (see 4.1),5.1.4 ASTM designation and year of issue,5.1.5 Hydrostatic test requirements (see 10.2),5.1.6 Inspection requirements (see 11.1

11、),1This specification is under the jurisdiction of ASTM Committee B10 onReactive and Refractory Metals and Alloys and is the direct responsibility ofSubcommittee B10.02 on Zirconium and Hafnium.Current edition approved May 1, 2016. Published May 2016. Originallyapproved in 1979. Last previous editio

12、n approved in 2011 as B653/B653M 11.DOI: 10.1520/B0653_B0653M-11R16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM w

13、ebsite.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from Manufacturers Standardization Society of the Valve and FittingsIndustry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http:/www.mss-.5Available from

14、 American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Ave., New York, NY 10016-5990, http:/www.asme.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.1.7 Finish (see Section 9), and5.1.8 Addi

15、tions to the specification and supplementaryrequirements, if required.NOTE 1A typical ordering description is as follows: 15 pieces,zirconium, 4-in. 100 mm, Schedule 40, 90 long radius elbows, descaled,ASTM B653 - 01, Grade R60702. Supplementary Requirement S3, StressRelief Heat Treatment.6. Materia

16、ls and Manufacture6.1 Forging, forming, or shaping operations may be per-formed by hammering, pressing, piercing, extruding, upsetting,rolling, bending, fusion welding, machining, or by a combina-tion of these operations. The forming procedure shall be soapplied that it will not produce injurious de

17、fects in the fittings.6.2 Fittings containing welded seams or other joints madeby welding shall comply with the following provisions:6.2.1 Welded by welders, welding operators, and weldingprocedures qualified under the provisions of Section IX of theASME Boiler and Pressure Vessel Code.6.2.2 Filler

18、metal, when used, shall be the same grade as thebase metal.6.2.3 All welds on grade R60705 shall be stress reliefannealed within 14 days after welding to prevent delayedhydride cracking, in accordance with Supplementary Require-ments Section S3, Stress Relief Heat Treatment.7. Chemical Composition7.

19、1 The material shall conform to the requirements as tochemical composition prescribed in Table 1.8. Tensile Requirements8.1 The material shall conform to the requirements as to thetensile properties prescribed in Table 1.9. Workmanship, Finish, and Appearance9.1 For fittings covered by ANSI B16.9 or

20、 MSS SP-43, orfor fittings to be used with pipe ordered to ANSI B36.19, thesizes, shapes, and dimensions of the fittings shall be asspecified in those standards.9.2 The fittings shall be free of injurious external andinternal imperfections of a nature that will interfere with thepurpose for which th

21、e fittings are intended. Minor defects maybe removed by grinding, providing the wall thickness is notdecreased to less than the minimum thickness, and furtherprovided that the ground-out area shall be faired out.10. Hydrostatic Tests10.1 All fittings shall be capable of withstanding withoutfailure,

22、leakage, or impairment of their serviceability, a testpressure prescribed in the applicable standards in Table 1 forthe pipe or tubing with which the fitting is planned to be used.10.2 Hydrostatic tests shall be performed when required bythe purchase order.11. Inspection11.1 The manufacturer shall i

23、nspect the material covered bythis specification prior to shipment. If so specified in thepurchase order, the purchaser or his representative may witnessthe testing and inspection of the material at the place ofmanufacture. In such cases the purchaser shall state in hispurchase order which tests he

24、desires to witness. The manu-facturer shall give ample notice to the purchaser as to the timeand place of the designated tests. If the purchasers represen-tative does not present himself at the time agreed upon for thetesting, the manufacturer shall consider the requirement for thepurchasers inspect

25、ion at the place of manufacture to bewaived.11.2 The manufacturer shall afford the inspector represent-ing the purchaser, without charge, all reasonable facilities tosatisfy him that the material is being furnished in accordancewith this specification. This inspection shall be so conducted asnot to

26、interfere unnecessarily with the operation of the works.12. Rejection12.1 Rejection for failure of the material to meet therequirements of this specification shall be reported to themanufacturer. Unless otherwise specified, rejected materialmay be returned to the manufacturer at the manufacturersexp

27、ense, unless the purchaser receives, within three weeks ofthe notice of rejection, other instructions for disposition.13. Certification13.1 A producer or supplier shall furnish the purchaser witha certificate that the material was manufactured, sampled,tested, and inspected in accordance with this s

28、pecification andhas been found to meet the requirements. The certificate shallinclude a report of the test results.13.2 All material incorporated within the fitting shall beidentified and shall be in accordance with the applicablestandards in Table 1.TABLE 1 Permissible Raw MaterialsGradeAProduct an

29、d ASTM DesignationPipe Tube Plate Bar ForgingPZ 2(R60702)B658/B658MGrade R60702B523/B523MGrade R60702B551/B551MGrade R60702B550/B550MGrade R60702B493Grade R60702PZ 4(R60704)B658/B658MGrade R60704B523/B523MGrade R60704B551/B551MGrade R60704B550/B550MGrade R60704B493Grade R60704PZ 5(R60705)B658/B658MG

30、rade R60705B523/B523MGrade R60705B551/B551MGrade R60705B550/B550MGrade R60705B493Grade R60705AWhen fittings are of welded construction, the symbol shown shall be supplemented by the letter “W.”B653/B653M 11 (2016)214. Referee14.1 In the event of disagreement between the manufacturerand the purchaser

31、 on the conformance of the material to therequirements of this specification or any special test specifiedby the purchaser, a mutually acceptable referee shall performthe tests in question. The results of the referees testing shall beused in determining conformance of the material to thisspecificati

32、on.15. Product Marking15.1 Unless otherwise specified, the manufacturers name ortrademark, the schedule number, material, and size shall bestamped (see Note 2), stenciled, electroetched, or otherwisesuitably marked on each fitting. In addition, each fitting shallbe marked with the identification gra

33、de symbol and suffix forthe respective specification listed in Table 1. On wall thick-nesses thinner than Schedule 40S, no stamps or other indentedmarkings shall be used. When the size does not permitcomplete marking, identification marks may be omitted in thesequence shown in MSS SP-25.NOTE 2When s

34、teel stamps are used, they should be applied prior toheat treatment and care should be taken so that the marking is not deepenough to cause cracks or to reduce the wall thickness of the fitting belowthe minimum allowed.16. Packaging and Package Marking16.1 The fittings shall be packaged suitably in

35、such amanner as to assure safe delivery to its destination whenproperly transported by common carrier.17. Keywords17.1 fitting; pipe; zirconium; zirconium alloySUPPLEMENTARY REQUIREMENTSSupplementary requirements shall not be considered unless specified in the order, in which event thetest shall be

36、made by the manufacturer at the purchasers expense.S1. Surface InspectionS1.1 Liquid penetrant inspection may be performed on alloutside-diameter surfaces of the fittings and inside-diametersurfaces where practicable. Acceptance shall be in accordancewith Appendix 8, Section VIII of the ASME Boiler

37、andPressure Vessel Code.S2. Radiographic Inspections of WeldsS2.1 Radiographic inspection may be performed on allweldments of the fittings in accordance with paragraph UW-51,Section VIII, of the ASME Boiler and Pressure Vessel Code.S3. Stress-Relief Heat TreatmentS3.1 The stress-relieving treatment

38、shall consist of holdingthe fitting at a minimum temperature of 1100F 600C for notless than 30 min per inch 25 mm of the maximum thicknessin a nonreducing atmosphere.S3.2 The minimum time at this temperature is 15 min. Allstress-relieved parts shall be cleaned subsequently and shall befree of oxide

39、scale contamination (see Practice B614).ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the

40、 riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of

41、 this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldm

42、ake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained

43、 by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 11 (2016)3