ASTM B650-1995(2013) Standard Specification for Electrodeposited Engineering Chromium Coatings on Ferrous Substrates《铁基物上电沉积工程镀铬层的标准规格》.pdf
《ASTM B650-1995(2013) Standard Specification for Electrodeposited Engineering Chromium Coatings on Ferrous Substrates《铁基物上电沉积工程镀铬层的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM B650-1995(2013) Standard Specification for Electrodeposited Engineering Chromium Coatings on Ferrous Substrates《铁基物上电沉积工程镀铬层的标准规格》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B650 95 (Reapproved 2013)Standard Specification forElectrodeposited Engineering Chromium Coatings onFerrous Substrates1This standard is issued under the fixed designation B650; the number immediately following the designation indicates the year oforiginal adoption or, in the case of rev
2、ision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This specific
3、ation covers the requirements for electrode-posited chromium coatings applied to ferrous alloys for engi-neering applications.1.2 Electrodeposited engineering chromium, which is some-times called “functional” or “hard” chromium, is usuallyapplied directly to the basis metal and is much thicker thand
4、ecorative chromium. Engineering chromium is used for thefollowing:1.2.1 To increase wear and abrasion resistance,1.2.2 To increase fretting resistance,1.2.3 To reduce static and kinetic friction,1.2.4 To reduce galling or seizing, or both, for various metalcombinations,1.2.5 To increase corrosion re
5、sistance, and1.2.6 To build up undersize or worn parts.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility
6、 of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B117 Practice for Operating Salt Spray (Fog) ApparatusB177 Guide for Engineering Chromium ElectroplatingB183 Practice for Preparation of Low-Carbon Steel forElectroplatingB242 Guide for Preparation of High-Carbon Stee
7、l for Elec-troplatingB320 Practice for Preparation of Iron Castings for Electro-platingB374 Terminology Relating to ElectroplatingB487 Test Method for Measurement of Metal and OxideCoating Thickness by Microscopical Examination ofCross SectionB499 Test Method for Measurement of Coating Thicknessesby
8、 the Magnetic Method: Nonmagnetic Coatings onMagnetic Basis MetalsB504 Test Method for Measurement of Thickness of Metal-lic Coatings by the Coulometric MethodB507 Practice for Design of Articles to Be Electroplated onRacksB568 Test Method for Measurement of Coating Thicknessby X-Ray SpectrometryB57
9、1 Practice for Qualitative Adhesion Testing of MetallicCoatingsB602 Test Method for Attribute Sampling of Metallic andInorganic CoatingsB697 Guide for Selection of Sampling Plans for Inspectionof Electrodeposited Metallic and Inorganic CoatingsB762 Test Method of Variables Sampling of Metallic andIn
10、organic CoatingsB849 Specification for Pre-Treatments of Iron or Steel forReducing Risk of Hydrogen EmbrittlementB850 Guide for Post-Coating Treatments of Steel for Reduc-ing the Risk of Hydrogen EmbrittlementD3951 Practice for Commercial PackagingE8 Test Methods for Tension Testing of Metallic Mate
11、rialsF1459 Test Method for Determination of the Susceptibilityof Metallic Materials to Hydrogen Gas Embrittlement(HGE)2.2 Other Standard:MIL-S-13165 Shot Peening of Metal Parts33. Terminology3.1 Definitions:1This specification is under the jurisdiction of ASTM Committee B08 onMetallic and Inorganic
12、Coatings and is the direct responsibility of SubcommitteeB08.03 on Engineering Coatings.Current edition approved Dec. 1, 2013. Published December 2013. Originallyapproved in 1978. Last previous edition approved in 2008 as B650 95(2008). DOI:10.1520/B0650-95R13.2For referenced ASTM standards, visit t
13、he ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelph
14、ia, PA 19111-5094, Attn: NPODS.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.1.1 significant surfacesall surfaces upon which a de-posit of controlled thickness is required.3.1.1.1 DiscussionWhen a controlled deposit is requiredin
15、holes, corners, recesses, and similar areas, special racking,auxiliary anodes or shielding, or both, will be necessary. Withthe best practices there will be areas where a controlled depositis impossible.3.2 Definitions used in this specification are in accordancewith Terminology B374.4. Classificati
16、on4.1 Electrodeposited chromium coatings in accordance withthis specification are classified by the thickness of the coatingas follows:Class No. Chromium Thickness, m Typical Application1 2.5 to 25 reduce friction; anti-galling, lightwear resistance2 25 as specified buildup to dimension specified fo
17、rsalvage or as required for severewear resistance4.2 Unless otherwise specified by suitably marked drawingsor samples, only those surfaces that can be touched with a20-mm diameter ball shall be considered significant. In holes,corners, recesses, and other areas where a controlled depositcannot be ob
18、tained under normal electroplating conditions, thethickness of the deposit may be that which results from controlon the significant surfaces.5. Ordering Information5.1 The purchaser shall exercise the desired options of thisstandard. Ordering documents shall specify the followinginformation:5.1.1 Ti
19、tle, ASTM designation, and issue date of thisspecification,5.1.2 Alloy and metallurgical condition of the product to bechromium plated,5.1.3 Ultimate tensile strength of the material to be plated,5.1.4 Heat treatment required for stress relief and whether ithas been performed or is required,5.1.5 Th
20、e significant surfaces if different from the 20-mmball rule (see 3.1.1),5.1.6 Thickness of the deposit or class (see 4.1),5.1.7 Control record requirements,5.1.8 Preproduction test specimens, if required,5.1.9 Sampling plan, if different from that specified in TestMethod B602 (see Section 8),5.1.10
21、The number of test specimens for destructive testing(see 7.1),5.1.11 Thickness, adhesion, porosity, and hydrogen em-brittlement tests required (see Section 6),5.1.12 Whether separate test specimens will be used (see 7.1and 7.5),5.1.13 Where required, any special requirements for partsthat are subseq
22、uently ground to size,5.1.14 Where required, the base metal finish in terms ofcenter line average (CLA) or arithmetic average (AA), and5.1.15 Where required, dimensional tolerances allowed forthe specified coating thickness or class.5.2 The manufacturer of the parts to be electroplated shallprovide
23、the electroplating facility with test specimens (seeSection 7) to be electroplated for conformance tests as re-quested for preparation, control, inspection, and lot acceptanceunless other arrangements have been made between the pur-chaser and the electroplating facility.6. Coating Requirements6.1 Th
24、e appearance of the chromium coating on the signifi-cant surfaces of the product shall be smooth and free of visualdefects such as blisters, pits, roughness, cracks, burneddeposits, uncoated areas, or macrocracking of the deposit thatis visible without magnification. The boundaries of electroplat-in
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB65019952013STANDARDSPECIFICATIONFORELECTRODEPOSITEDENGINEERINGCHROMIUMCOATINGSONFERROUSSUBSTRATES

链接地址:http://www.mydoc123.com/p-461868.html