ASTM B625-2005(2011) Standard Specification for UNS N08925 UNS N08031 UNS N08932 UNS N08926 UNS N08354 and UNS R20033 Plate Sheet and Strip《UNS N08925 UNS N08031 NS N08932 UNS N089.pdf

《ASTM B625-2005(2011) Standard Specification for UNS N08925 UNS N08031 UNS N08932 UNS N08926 UNS N08354 and UNS R20033 Plate Sheet and Strip《UNS N08925 UNS N08031 NS N08932 UNS N089.pdf》由会员分享，可在线阅读，更多相关《ASTM B625-2005(2011) Standard Specification for UNS N08925 UNS N08031 UNS N08932 UNS N08926 UNS N08354 and UNS R20033 Plate Sheet and Strip《UNS N08925 UNS N08031 NS N08932 UNS N089.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B625 05 (Reapproved 2011)Standard Specification forUNS N08925, UNS N08031, UNS N08932, UNS N08926, UNSN08354, and UNS R20033 Plate, Sheet, and Strip1This standard is issued under the fixed designation B625; the number immediately following the designation indicates the year oforiginal a

2、doption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers alloys UNS N08925,* UNSN08031, UNS N08932,

3、UNS N08926, UNS N08354, and UNSR20033 plate, sheet, and strip in the annealed temper.1.2 ASTM International has adopted definitions wherebysome grades, such as UNS N08904, previously in this speci-fication were recognized as stainless steels, because thosegrades have iron as the largest element by m

4、ass percent. Suchgrades are under the oversight of ASTM Committee A01 andits subcommittees. The products of N08904 previously coveredin this specification are now covered by Specifications A240/A240M and A480/A480M.1.3 The values stated in inch-pound units are to be regardedas standard. The values g

5、iven in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become f

6、amiliarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Do

7、cuments2.1 ASTM Standards:2A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for PressureVessels and for General ApplicationsA480/A480M Specification for General Requirements forFlat-Rolled Stainless and Heat-Resisting Steel Plate,Sheet, and StripB906

8、Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and StripE527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 plate, nmaterial316 in. (4.76 mm) and over i

9、nthickness and over 10 in. (254 mm) in width.3.1.2 sheet, nmaterial under316 in. (4.76 mm) in thick-ness and 24 in. (609.6 mm) and over in width. Material under316 in. (4.75 mm) in thickness and in all widths with No. 4finish.3.1.3 strip, nmaterial under316 in. (4.76 mm) in thicknessand under 24 in.

10、 (609.6 mm) in width.4. General Requirements4.1 Material furnished in accordance with this specificationshall conform to the applicable requirements of the currentedition of Specification B906 unless otherwise providedherein.5. Ordering Information5.1 Orders for material under this specification sha

11、ll includethe following information:5.1.1 Quantity (weight or number of pieces),5.1.2 Alloy name or UNS number,5.1.3 Form, plate, sheet or strip,5.1.4 Dimensions,5.1.5 Type edge required, for strip only (see SpecificationB906),5.1.6 Finish (see Specification B906)For sheet with No. 4finish, specify

12、whether one or both sides are to be polished,5.1.7 ASTM designation,5.1.8 Additions to the specification or special requirements,5.1.9 Certification or test reportsState if certification ortest reports are required, and1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous

13、Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and Their Alloys.Current edition approved May 1, 2011. Published May 2011. Originallyapproved in 1977. Last previous edition approved in 2005 as B625 05. DOI:10.1520/B0625-05R11.* New designation es

14、tablished in accordance with Practice E527 and SAE J1086,Practice for Numbering Metals and Alloys (UNS).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standard

15、s Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.1.10 Source inspectionState if inspection is required.6. Chemical Composition6.1 The material shall conform to the composition limitsspecifi

16、ed in Table 1. One test per lot is required as defined inSpecification B906.6.2 If a product analysis is made by the purchaser, thematerial shall conform to the product (check) analysis varia-tions in Specification B906.7. Mechanical Properties and Other Requirements7.1 Tensile and Hardness Requirem

17、entsThe material shallconform to the mechanical property requirements specified inTable 2. One test per lot is required as defined in SpecificationB906.8. Dimensions and Permissible Variations8.1 SheetThe material shall be furnished in accordancewith the dimensional requirements established in Speci

18、ficationB906.9. Keywords9.1 UNS N08031; UNS N08925; UNS N08926; UNSN08932; UNS N08354; UNS R20033; plate; sheet; stripASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly

19、 advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, ei

20、ther reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may atten

21、d. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. In

22、dividual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secure

23、d from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Chemical RequirementsElementsUNS N08925 UNS N08932 UNS N08354 UNS N08031 UNS N08926 UNS R20033Carbon, max 0.020 0.020 0.030 0.015 0.020 0.015Manganese, max 1.00 2.00 1.00 2.0 2.00 2.0Phosphorus, max 0.045 0.025 0.030 0.020 0.03 0.02Sulfur, ma

24、x 0.030 0.010 0.010 0.010 0.01 0.01Silicon, max 0.50 0.40 1.00 0.3 0.5 0.50Nickel 24.0026.00 24.026.0 34.036.0 30.032.0 24.0026.00 30.033.0Chromium 19.0021.00 24.026.0 22.024.0 26.028.0 19.0021.00 31.035.0Molybdenum 6.07.0 4.56.5 7.08.0 6.07.0 6.07.0 0.502.0Copper 0.81.5 1.02.0 . 1.01.4 0.51.5 0.301

25、.20Nitrogen 0.100.20 0.150.25 0.170.24 0.150.25 0.150.25 0.350.60Iron balance balance balance balance balance balanceTABLE 2 Mechanical Property RequirementsAlloy FormTensile Strength, min,ksi (MPa)Yield Strength (0.2 % offset), min, psi(MPa)Elongation in 2 in. or 50.8mm, or 4D,min,%Rockwell Hardnes

26、s (orequivalent)AUNS N08925 sheet 87 (600) 43 000 (295) 40 .strip 87 (600) 43 000 (295) 40 .plate 87 (600) 43 000 (295) 40 .UNS N08932 plate 87 (600) 44 000 (305) 40 .UNS N08031 sheet 94 (650) 40 000 (276) 40 .strip 94 (650) 40 000 (276) 40 .plate 94 (650) 40 000 (276) 40 .UNS N08926 sheet 94 (650)

27、43 000 (295) 35 .strip 94 (650) 43 000 (295) 35 .plate 94 (650) 43 000 (295) 35 .UNS N08354 sheet 93 (640) 43 000 (295) 40 .strip 93 (640) 43 000 (295) 40 .plate 93 (640) 43 000 (295) 40 .UNS R20033 sheet 109 (750) 55 000 (380) 40 .strip 109 (750) 55 000 (380) 40 .plate 109 (750) 55 000 (380) 40 .AHardness values are shown for information only and shall not constitute a basis for acceptance or rejection as long as the other mechanical properties are met.B625 05 (2011)2