ASTM B619 B619M-2017 Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe《焊接镍和镍-钴合金管的标准规格》.pdf
《ASTM B619 B619M-2017 Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe《焊接镍和镍-钴合金管的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM B619 B619M-2017 Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe《焊接镍和镍-钴合金管的标准规格》.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B619/B619M 15B619/B619M 17Standard Specification forWelded Nickel and Nickel-Cobalt Alloy Pipe1This standard is issued under the fixed designation B619/B619M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of
2、 last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification2 covers welded pipe of nickel and nickel-cobalt alloys (UNS N10001; UNS N10242; UNS N10665; UNSN1
3、2160; UNS N10624; UNS N10629; UNS N10675; UNS N10276; UNS N06455; UNS N06007; UNS N06975; UNS N08320;UNS N06002; UNS N06022; UNS N06035; UNS N06044; UNS N06058; UNS N06059; UNS N06200; UNS N10362; UNSN06985; UNS N06030; UNS R30556; UNS N08031; UNS N06230; UNS N06686; UNS N06210; and UNS R20033)3 as
4、shownin Table 1.1.2 This specification covers pipe in Schedules 5S, 10S, 40S, and 80S through 8-in. nominal pipe size and larger as set forthin ANSI B36.19 (see Table 2).1.3 Two classes of pipe are covered as follows:1.3.1 Class IAs welded and solution annealed or welded and sized and solution annea
5、led.1.3.2 Class IIWelded, cold worked, and solution annealed.1.4 All pipe shall be furnished in the solution annealed and descaled condition. When atmosphere control is used, descaling isnot necessary.1.5 The values stated in either SI units or inch-pound units are to be regarded separately as stand
6、ard. The values stated in eachsystem may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from thetwo systems may result in non-conformance with the standard.1.6 This standard does not purport to address all of the safety concerns, if any, a
7、ssociated with its use. It is the responsibilityof the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet(SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, andde
8、termine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendatio
9、ns issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:4B775 Specification for General Requirements for Nickel and Nickel Alloy Welded PipeB899 Terminology Relating to Non-ferrous Metals and AlloysE527 Practice for Numbering Met
10、als and Alloys in the Unified Numbering System (UNS)2.2 ANSI Standards:5B36.19 Stainless Steel PipeB2.1 Pipe Threads2.3 ASME Boiler and Pressure Vessel Code6Section IX Welding and Brazing Qualifications1 This specification is under the jurisdiction ofASTM Committee B02 on Nonferrous Metals andAlloys
11、 and is the direct responsibility of Subcommittee B02.07 on RefinedNickel and Cobalt and Their Alloys.Current edition approved Oct. 1, 2015June 1, 2017. Published October 2015June 2017. Originally approved in 1981. Last previous edition approved in 20102015 asB619 10B619/B619M 15.2. DOI: 10.1520/B06
12、19_B0619M-15.10.1520/B0619_B0619M-17.2 For ASME Boiler and Pressure Vessel Code applications see related Specification SB-619 in Section II of that Code.3 New designation established in accordance with Practice E527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).4 For referencedASTM s
13、tandards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.5 Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th
14、Floor, New York, NY 10036, http:/www.ansi.org.6 Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http:/www.asme.org.This document is not an ASTM standard and is intended only to provide the user of an ASTM stan
15、dard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by AST
16、M is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1TABLE 1 Chemical RequirementsComposition Limits, %Ni Cr Mo Fe W C SimaxCo Mn
17、V PmaxSmaxTi Cu Cb(Nb)+TaAl Zr La N B Cb(Nb)Ta Ni+MoMgNi-Mo AlloysN10001 remainderA 1.0max26.0-30.04.0-6.0 . 0.05max1.0 2.5max1.0max0.2-0.40.04 0.03 . . .N10665 remainderA 1.0max26.0-30.02.0 max . 0.02max0.10 1.0max1.0max. 0.04 0.03 . . .N10675 65.0 min 1.0-3.027.0-32.01.0-3.0 3.0max0.01max0.10 3.0m
18、ax3.0max0.20max0.030 0.010 0.20max0.20max. 0.50max0.10max. . . 0.20max0.20max94.0-98.0N10629 remainderA 0.5-1.526.0-30.01.0-6.0 . 0.01max0.05 2.5max1.5max. 0.04 0.01 . 0.5max. 0.1-0.5. . . . . . .N10624 remainderA 6.0-10.021.0-25.05.0-8.0 . 0.01max0.10 1.0max1.0max. 0.025 0.01 . 0.5max. . . . . . .
19、. .Ni-Mo-Cr-FeAlloyN10242 remainderA 7.0-9.024.0-26.02.0 max 0.03max0.80 1.00max0.80max0.030 0.015 0.50max0.50max0.006maxLow C Ni-Cr-Mo AlloysN10276 remainderA 14.5-16.515.0-17.04.0-7.0 3.0-4.50.010max0.08 2.5max1.0max0.35max0.04 0.03 . . .N06022 remainderA 20.0-22.512.5-14.52.0-6.0 2.5-3.50.015max0
20、.08 2.5max0.5max0.35max0.02 0.02 . . .N06035 remainderA 32.25-34.257.60-9.002.00 max 0.60max0.050max0.60 1.00max0.50max0.20max0.030 0.015 . 0.30max. 0.40maxN06044 balance 43.5-45.30.80-1.20 0.3 max. 0.02max 0.20. 0.07-0.30. 0.020 0.020 0.10-0.30. . 0.30max. . . . . . . .N06058 balance 20.0-23.018.5-
21、21.01.5 max 0.3max0.010max0.10max0.3max0.50max0.015 0.010 . 0.50max. 0.40max0.02-0.15N06059 balance 22.0-24.015.0-16.51.5 max . 0.010max0.10 0.3max0.5max. 0.015 0.010 . 0.50max. 0.1-0.4. . . . . . .N06455 remainderA 14.0-18.014.0-17.03.0 max . 0.015max0.08 2.0max1.0max. 0.04 0.03 0.70max. .Ni-Cr-Fe-
22、Mo-CuAlloysN06007 remainderA 21.0-23.55.5-7.518.0-21.0 1.0max0.05max1.0 2.5max1.0-2.0. 0.04 0.03 . 1.5-2.51.75-2.5N06975 47.0-52.0 23.0-26.05.0-7.0remainder . 0.03max1.0 . 1.0max. 0.03 0.03 0.70-1.500.70-1.20.N06985 remainderA 21.0-23.56.0-8.018.0-21.0 1.5max0.015max1.0max5.0max1.0max. 0.04 0.03 . 1
23、.5-2.50.50maxN06030 remainderA 28.0-31.54.0-6.013.0-17.0 1.5-4.00.03max0.8 5.0max1.5max. 0.04 0.02 . 1.0-2.40.30-1.50Ni-Fe-Cr-MoAlloysN08320 25.0-27.0 21.0-23.04.0-6.0remainder . 0.05max1.0 . 2.5max. 0.04 0.03 4xCmin. .Ni-Cr-Mo-FeAlloyN06002 remainderA 20.5-23.08.0-10.017.0-20.0 0.20-1.00.05-0.151.0
24、 0.5-2.51.0max. 0.04 0.03 . . .Ni-Fe-Cr-CoAlloyR30556 19.0-22.5 21.0-23.02.5-4.0remainder 2.0-3.50.05-0.150.20-0.8016.0-21.00.50-2.00. 0.04 0.015 . . . 0.10-0.500.001-0.100.005-0.100.10-0.300.02max0.30max0.3-1.25B619/B619M172TABLE 1 ContinuedComposition Limits, %Ni Cr Mo Fe W C SimaxCo Mn V PmaxSmax
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB619B619M2017STANDARDSPECIFICATIONFORWELDEDNICKELANDNICKELCOBALTALLOYPIPE 焊接 合金管 标准 规格 PDF

链接地址:http://www.mydoc123.com/p-461758.html