ASTM B570-2016 Standard Specification for Copper-Beryllium Alloy (UNS Nos C17000 and C17200) Forgings and Extrusions《铍铜合金(UNS编号C17000和C17200)锻件和挤压件的标准规格》.pdf

《ASTM B570-2016 Standard Specification for Copper-Beryllium Alloy (UNS Nos C17000 and C17200) Forgings and Extrusions《铍铜合金(UNS编号C17000和C17200)锻件和挤压件的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B570-2016 Standard Specification for Copper-Beryllium Alloy (UNS Nos C17000 and C17200) Forgings and Extrusions《铍铜合金(UNS编号C17000和C17200)锻件和挤压件的标准规格》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B570 16Standard Specification forCopper-Beryllium Alloy (UNS Nos. C17000 and C17200)Forgings and Extrusions1This standard is issued under the fixed designation B570; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the

2、year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification establishes the requirements forcopper-beryllium alloy forgings and extrusions produced fr

3、omthe following alloys.Copper Alloy UNS No.Nominal % CompositionBerylliumC17000C172001.71.9NOTE 1Requirements for copper-beryllium alloy rod and bar appearin Specification B196/B196M (Section 2).1.2 Unless otherwise specified, Copper Alloy UNS No.C17200 shall be the alloy furnished whenever Specific

4、ationB570 is specified without any alloy designation.1.3 UnitsThe values stated in inch-pound units are to beregarded as standard. The values given in parentheses aremathematical conversions to SI units which are provided forinformation only and are not considered standard.1.4 The following safety h

5、azard caveat pertains only to thetest method(s) described in this specification:1.4.1 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and t

6、o determine theapplicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B194 Specification for Copper-BerylliumAlloy Plate, Sheet,Strip, and Rolled BarB196/B196M Specification for Copper-BerylliumAlloy Rodand BarB249/B249M Specification for General Requirements

7、 forWrought Copper and Copper-Alloy Rod, Bar, Shapes andForgingsB601 Classification for Temper Designations for Copper andCopper AlloysWrought and CastB846 Terminology for Copper and Copper AlloysE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE18 Test Methods for Rockwell Hardness of

8、Metallic Ma-terialsE112 Test Methods for Determining Average Grain Size3. General Requirements3.1 The following sections of Specification B249/B249Mform a part of this specification.3.1.1 Terminology,3.1.2 Materials and Manufacture,3.1.3 Sampling,3.1.4 Number of Tests and Retests,3.1.5 Sample Prepar

9、ation,3.1.6 Test Methods,3.1.7 Significance of Numerical Limits,3.1.8 Inspection,3.1.9 Rejection and Rehearing,3.1.10 Certification,3.1.11 Mill Test Report,3.1.12 Packaging, Marking, Shipping and Preservation.3.2 In addition, when a section with a title identical to thatreferenced in 3.1, above, app

10、ears in this specification, itcontains additional requirements that supplement those appear-ing in Specification B249/B249M.4. Terminology4.1 Definitions:4.1.1 For definitions of terms related to copper and copperalloys, refer to Terminology B846.4.1.2 forging, na metal part worked to a predetermine

11、dshape by one or more such processes as hammering, upsetting,pressing, rolling, and so forth.5. Ordering Information5.1 Include the following specified choices when placingorders for products under this specification, as applicable:1This specification is under the jurisdiction ofASTM Committee B05 o

12、n Copperand Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod,Bar, Wire, Shapes and Forgings.Current edition approved Oct. 1, 2016. Published November 2016. Originallyapproved in 1972. Last previous edition approved in 2010 as B57006(2010). DOI:10.1520/B0570-16.2For refere

13、nced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyrig

14、ht ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15.1.1 ASTM designation and year of issue,5.1.2 Copper Alloy UNS No. designation (Section 1),5.1.3 Temper (Section 8) or condition (Section 12),5.1.4 Drawing showing the shape, dimensions, andto

15、lerances, if required,5.1.5 Quantitytotal weight, or length, or number of piecesof each size,5.1.6 If an extrusion: the length (or mass) required, straight-ness as required,5.2 The following options are available but may not beincluded unless specified at the time of placing of the order,when requir

16、ed:5.2.1 Tension tests (Section 11),5.2.2 Finish (see Section 15),5.2.3 Grain size (see Section 9), and5.2.4 If product is purchased for agencies of the U.S.Government (see the Supplementary Requirements section ofthis specification) for additional requirements, if specified.6. Material and Manufact

17、ure6.1 Material:6.1.1 The material of manufacture shall be cast or wroughtbillet of Copper Alloy UNS No. C17000 or C17200 of suchpurity and soundness as to be suitable for processing into theproducts prescribed herein.6.1.2 The product heat number shall appear on the certifi-cation or test report.6.

18、2 Manufacture:6.2.1 The product shall be manufactured by hot workingand heat treating, when required, to meet the temper propertiesspecified.7. Chemical Composition7.1 The material shall conform to the chemical compositionrequirements in Table 1 for the copper alloy UNS No.designation specified in t

19、he ordering information.7.2 These composition limits do not preclude the presenceof other elements. By agreement between the manufacturer andpurchaser, limits may be established and analysis required forunnamed elements.7.3 For alloys in which copper is listed as “remainder,”copper is the difference

20、 between the sum of results of allelements determined and 100 %. When all the elements givenin Table 1 are determined, the sum of the results shall be99.5 % minimum.8. Temper8.1 The standard tempers for products described in thisspecification are given in Tables 2 and 3.8.1.1 The standard temper des

21、ignations available under thisspecification and as prescribed in Classification B601 are TB00solution heat-treated (A) and TF00 precipitation heat-treated(AT).9. Grain Size9.1 The grain size, if required, shall be as agreed uponbetween the purchaser and the manufacturer and shall bedetermined in acc

22、ordance with Test Methods E112.10. Physical Property Requirements10.1 Microstructure:10.1.1 The product in the TF00 (precipitation-hardened(AT) condition shall have a microstructure with a minimum ofsecond phase (beta) constituents. When present, beta shall befine and well dispersed.11. Mechanical P

23、roperty Requirements11.1 HardnessThe product furnished under this specifica-tion shall conform to the hardness requirements prescribed inTable 2 for the solution heat-treated condition and Table 3 afterprecipitation heat treatment, unless tensile properties are re-quired by the purchase order. Rockw

24、ell hardness shall bedetermined in accordance with Test Methods E18.11.2 TensileWhen specified in the contract or purchaseorder, the tensile properties of the product furnished shallconform to the properties in Table 2 or Table 3 depending upontemper required. Tensile properties shall be determined

25、inaccordance with Test Methods E8/E8M.12. Heat Treatment12.1 Solution Heat TreatmentTemper TB00 (A)Theproduct shall be heated to a uniform temperature, nominally1450F (788C) and quenched commensurate with the requiredproperty and structural integrity of the configuration.12.2 Precipitation Heat Trea

26、tmentTemper TF00 (AT)The product shall be heat treated to a uniform temperature inthe range from 600 to 700F (316 to 370C) for a minimum of2 to 3 h and then air cooled. This is the heat treatment for theacceptance tests shown in Table 3.12.3 Special combinations of properties may be obtained byspeci

27、al precipitation heat treatments. The requirements forthese special heat treatments shall be agreed upon by themanufacturer or supplier and purchaser.13. Purchases for the U.S. Government13.1 When specified in the contract or purchase order,product purchased for agencies of the U.S. government shall

28、conform to the special government regulations specified in theSupplementary Requirements section.14. Dimensions and Permissible Variations14.1 The dimensions and tolerances for these product formsshall be those shown on the drawing that forms a part of eachorder or as agreed upon between the manufac

29、turer and thepurchaser.TABLE 1 Chemical RequirementsComposition, %ElementCopper AlloyUNS No. C17000Copper AlloyUNS No. C17200Beryllium 1.601.85 1.802.00Additive elements:Nickel + cobalt, min 0.20 0.20Nickel + cobalt + iron, max 0.6 0.6Aluminum, max 0.20 0.20Silicon, max 0.20 0.20Copper remainder rem

30、ainderB570 16215. Workmanship, Finish, and Appearance15.1 The product shall be free of defects but blemishes of anature that do not interfere with the intended application areacceptable.15.2 The purchaser shall specify in the order the conditionor finish required, such as, hot-worked, hot-worked and

31、cleaned by blasting, pickling, or machining.16. Test Methods16.1 Chemical Composition:16.2 The chemical composition shall, in case ofdisagreement, be determined in accordance with the applicablemethod in the Annex of Specification B194.16.3 Test method(s) for the determination of element(s)required

32、by contractual agreement shall be as agreed uponbetween the manufacturer and the purchaser.17. Keywords17.1 copper beryllium; extrusions; forgings; UNS C17000;UNS C17200SUPPLEMENTARY REQUIREMENTSThe following supplementary requirements shall apply only when specified by the purchaser in theinquiry,

33、contract, or order, for agencies of the U.S. government.S1. Referenced DocumentsS1.1 The following documents of the issue in effect on dateof material purchase form a part of this specification to theextent referenced herein:S1.1.1 ASTM Standard:B900 Practice for Packaging of Copper and Copper-Alloy

34、Mill-Products for U.S. Government AgenciesS1.1.2 Federal Standards:3Fed. Std. No. 102 Preservation, Packaging and PackingLevelsFed. Std. No. 123 Marking for Shipment (Civil Agencies)Fed. Std. No. 185 Identification Marking of Copper andCopper-Base Alloy Mill ProductsS1.1.3 Military Standards:3MIL-ST

35、D-105 Sampling Procedures and Tables for Inspec-tion by AttributesMIL-STD-129 Marking for Shipment and StorageS2. Quality AssuranceS2.1 Responsibility for Inspection:S2.1.1 Unless otherwise specified in the contract or pur-chase order, the manufacturer is responsible for the perfor-mance of all insp

36、ection and test requirements specified. Exceptas otherwise specified in the contract or purchase order, themanufacturer may use his own or any other suitable facilitiesfor the performance of the inspection and test requirements,3Available from DLA Document Services, Building 4/D, 700 Robbins Ave.,Ph

37、iladelphia, PA 19111-5094, http:/quicksearch.dla.mil.TABLE 2 Mechanical Properties as Solution Heat TreatedTemper DesignationDiameter orThickness,in. (mm)Copper Alloy UNS No.C17000 C17200 C17000 C17200Standard Former Tensile Strength, ksi (MPa),A, Bmax Rockwell Hardness, maxB ScaleTB00 solution heat

38、-treated (A) all sizes 85 (590) 85 (590) 85 85Aksi = 1000 psi.BSee Appendix X1.TABLE 3 Mechanical Properties After Precipitation Heat TreatmentTemper DesignationStandard Former In. mmCopper AlloyUNS No.Tensile Strength,ksiA(MPa)B, CYield Strength, ksi(MPa), 0.2 % Offset,minElongation in4D,Dmin, %Roc

39、kwellC ScaleTF00 precipita-tion hard-ened (AT)UNS C17000 150190 (10301310) 120 (820) 3 32Up to 8, incl up to 200; 165200 (11401380) 130 (890) 3 36TF00 precipita-tion hard-ened (AT)Over 8 to 12, incl., over 200 to 300; UNS C17200 155190 (10701310) 130 (890) 3 34Over 12 over 300 145180 (10001240) 125

40、(860) 3 34Aksi = 1000 psi.BSee Appendix X1.CThe upper limits in the tensile strength column are for design guidance only.D4D = 4Diameter.B570 163unless disapproved by the purchaser at the time the order isplaced. The purchaser shall have the right to perform any of theinspections or tests set forth,

41、 when such inspections and testsare deemed necessary to assure that the material conforms toprescribed requirements.S3. Identification MarkingS3.1 All material shall be properly marked for identificationin accordance with Fed. Std. No. 185 except that the ASTMspecification number and the alloy numbe

42、r shall be used.S4. Preparation for DeliveryS4.1 Preservation, Packaging, Packing:S4.1.1 Military AgenciesThe material shall be separatedby size, composition, grade or class, and shall be preserved andpackaged, Level A or C, packed Level A, B, or C as specifiedin the contract or purchase order, in a

43、ccordance with therequirements of Practice B900.S4.1.2 Civil AgenciesThe requirements of Fed. Std. No.102 shall be referenced for definitions of the various levels ofpackaging protection.S4.2 Marking:S4.2.1 Military AgenciesIn addition to any special mark-ing required by the contract or purchase ord

44、er, marking forshipment shall be in accordance with MIL-STD-129.S4.2.2 Civil AgenciesIn addition to any special markingrequired by the contract or purchase order, marking forshipment shall be in accordance with Fed. Std. No. 123.APPENDIX(Nonmandatory Information)X1. METRIC EQUIVALENTSX1.1 The SI uni

45、t for strength properties now shown is inaccordance with the International System of Units (SI). Thederived SI unit for force is the newton (N), which is defined asthat force which when applied to a body having a mass of 1 kggives it an acceleration of 1 m/s2(N = kgm s2). The derived SIunit for pres

46、sure or stress is the newton per square metre(N/m2), which has been named the pascal (Pa) by the GeneralConference on Weights and Measures. Since 1 ksi = 6 894 757Pa, the metric equivalents are expressed as megapascal (MPa),which is the same as MN/m2and N/mm2.SUMMARY OF CHANGESCommittee B05 has iden

47、tified the location of selected changes to this standard since the last issue(B570 06(2010) that may impact the use of this standard. (Approved Oct. 1, 2016.)(1) There were no technical changes. The specification has hadan editorial review and update.ASTM International takes no position respecting t

48、he validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard

49、is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the AS