ASTM B545-2013 Standard Specification for Electrodeposited Coatings of Tin《锡电解沉积层标准规格》.pdf
《ASTM B545-2013 Standard Specification for Electrodeposited Coatings of Tin《锡电解沉积层标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM B545-2013 Standard Specification for Electrodeposited Coatings of Tin《锡电解沉积层标准规格》.pdf(9页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B545 13Standard Specification forElectrodeposited Coatings of Tin1This standard is issued under the fixed designation B545; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parenth
2、eses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers the requirements for electrode-posited (elect
3、roplated) coatings of tin applied to metallicarticles. Tin coatings are used to provide a low contact-resistance surface, to protect against corrosion (see 1.2), tofacilitate soldering, to provide anti-galling properties, and to bea stopoff coating in the nitriding of high-strength steels.1.2 Some c
4、orrosion can be expected from tin coatingsexposed outdoors. In normal indoor exposure, tin is protectiveon iron, steel, nickel, copper, and their alloys. Corrosion can beexpected at discontinuities in the coating (such as pores) due togalvanic couples formed between the tin and the underlyingmetal t
5、hrough the discontinuities, especially in humid atmo-spheres. Porosity increases as the coating thickness decreases,so that minimum thicknesses must be specified for eachapplication. Parts coated with tin can be assembled safely incontact with iron and steel, tin-coated aluminum, yellowchromated zin
6、c, cadmium, and solder coatings. (See X5.1 foroxidation and corrosion properties.)1.3 This specification applies to electroplated coatings ofnot less than 99 % tin (except where deliberately alloyed forspecial purposes, as stated in X6.3) obtained from any of theavailable tin electroplating processe
7、s (see 4.3).1.4 This specification does not apply to hot-dipped tin orother non-electrodeposited coating; it also does not apply tomill products. For mill products, refer to Specifications A623or A623M.1.5 The values stated in SI units are to be regarded as thestandard. The values given in parenthes
8、es are for informationonly.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations p
9、rior to use.2. Referenced Documents2.1 ASTM Standards:2A623 Specification for Tin Mill Products, General Require-mentsA623M Specification for Tin Mill Products, General Re-quirements MetricB32 Specification for Solder MetalB183 Practice for Preparation of Low-Carbon Steel forElectroplatingB242 Guide
10、 for Preparation of High-Carbon Steel for Elec-troplatingB246 Specification for Tinned Hard-Drawn and Medium-Hard-Drawn Copper Wire for Electrical PurposesB281 Practice for Preparation of Copper and Copper-BaseAlloys for Electroplating and Conversion CoatingsB320 Practice for Preparation of Iron Cas
11、tings for Electro-platingB322 Guide for Cleaning Metals Prior to ElectroplatingB374 Terminology Relating to ElectroplatingB487 Test Method for Measurement of Metal and OxideCoating Thickness by Microscopical Examination ofCross SectionB499 Test Method for Measurement of Coating Thicknessesby the Mag
12、netic Method: Nonmagnetic Coatings onMagnetic Basis MetalsB504 Test Method for Measurement of Thickness of Metal-lic Coatings by the Coulometric MethodB507 Practice for Design of Articles to Be Electroplated onRacksB542 Terminology Relating to Electrical Contacts and TheirUseB558 Practice for Prepar
13、ation of Nickel Alloys for Electro-platingB567 Test Method for Measurement of Coating Thicknessby the Beta Backscatter MethodB568 Test Method for Measurement of Coating Thicknessby X-Ray Spectrometry1This specification is under the jurisdiction of ASTM Committee B08 onMetallic and Inorganic Coatings
14、 and is the direct responsibility of SubcommitteeB08.06 on Soft Metals.Current edition approved May 1, 2013. Published July 2013. Originally approvedin 1971. Last previous edition approved in 2009 as B545 97 (2009). DOI:10.1520/B0545-13.2For referenced ASTM standards, visit the ASTM website, www.ast
15、m.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1B571 Pract
16、ice for Qualitative Adhesion Testing of MetallicCoatingsB602 Test Method for Attribute Sampling of Metallic andInorganic CoatingsB659 Guide for Measuring Thickness of Metallic and Inor-ganic CoatingsB678 Test Method for Solderability of Metallic-CoatedProductsB697 Guide for Selection of Sampling Pla
17、ns for Inspectionof Electrodeposited Metallic and Inorganic CoatingsB762 Test Method of Variables Sampling of Metallic andInorganic CoatingsB765 Guide for Selection of Porosity and Gross Defect Testsfor Electrodeposits and Related Metallic CoatingsB809 Test Method for Porosity in Metallic Coatings b
18、yHumid Sulfur Vapor (“Flowers-of-Sulfur”)B849 Specification for Pre-Treatments of Iron or Steel forReducing Risk of Hydrogen EmbrittlementB850 Guide for Post-Coating Treatments of Steel for Reduc-ing the Risk of Hydrogen EmbrittlementB851 Specification for Automated Controlled Shot Peeningof Metalli
19、c Articles Prior to Nickel, Autocatalytic Nickel,or Chromium Plating, or as Final FinishD3951 Practice for Commercial Packaging3. Terminology3.1 Definitions:3.1.1 Many of the terms used in this specification aredefined in Terminology B374 or B542.3.1.2 rack-platingan electrodeposition process in whi
20、charticles to be coated are mounted on racks or other fixturesduring the process.3.1.3 significant surfacethat portion of the surface of acoated article at which the coating is required to meet all of therequirements of the coating specification for that article;significant surfaces are usually thos
21、e that are essential to theserviceability or function of the article, or that can be a sourceof corrosion products or tarnish films that interfere with thefunction or desirable appearance of the article; significantsurfaces shall be indicated on the drawings of the parts or bythe provision of suitab
22、ly marked samples.3.1.4 undercoating (see 3.1.5)also called an underplate inthe electronics industry.3.1.5 underplatingapplication of a metallic coating layerbetween the basis metal or substrate and the topmost metalliccoating or coatings. The thickness of such an undercoating isusually greater than
23、 0.8 m (30 in.). This is in contrast tostrikes or flashes, whose thicknesses are generally muchsmaller.4. Classification4.1 GeneralOrders for articles to be plated in accordancewith this specification shall specify the service class (4.2) (andunderplating, if required), indicating the severity of se
24、rvicerequired for the coating. Other coatings variations, such assurface appearance type (4.3) or alloy composition (AppendixX6), are optional.4.2 Service Class:Class Minimum Thickness Typical ApplicationsA 2.5 m (100 in.) Mild service conditions, particularly where thesignificant surface is shielde
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB5452013STANDARDSPECIFICATIONFORELECTRODEPOSITEDCOATINGSOFTIN 电解 沉积 标准 规格 PDF

链接地址:http://www.mydoc123.com/p-461517.html