ASTM B500 B500M-2010 Standard Specification for Metallic Coated Stranded Steel Core for Use in Overhead Electrical Conductors《高架电导体用金属涂覆钢绞线芯的标准规格》.pdf

《ASTM B500 B500M-2010 Standard Specification for Metallic Coated Stranded Steel Core for Use in Overhead Electrical Conductors《高架电导体用金属涂覆钢绞线芯的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B500 B500M-2010 Standard Specification for Metallic Coated Stranded Steel Core for Use in Overhead Electrical Conductors《高架电导体用金属涂覆钢绞线芯的标准规格》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B500/B500M 10Standard Specification forMetallic Coated Stranded Steel Core for Use in OverheadElectrical Conductors1This standard is issued under the fixed designation B500/B500M; the number immediately following the designation indicates the yearof original adoption or, in the case of

2、revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers 7-wire, 19-wire, 37-wire, and61-wire zinc-coated (galvanized), zinc-5

3、 % aluminum-mischmetal alloy-coated stranded steel core intended for use inoverhead electrical conductors.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall b

4、e used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.2. Referenced Documents2.1 ASTM Standards:2B498/B498M Specification for Zinc-Coated (Galvanized)Steel Core Wire for Use in Overhead Electrical ConductorsB957 Specification for Extra

5、-High-Strength and Ultra-High-Strength Zinc-Coated (Galvanized) Steel Core Wirefor Overhead Electrical ConductorsB958 Specification for Extra-High-Strength and Ultra-High-Strength Class A Zinc5% Aluminum-MischmetalAlloy-Coated Steel Core Wire for Use in Overhead Elec-trical ConductorsB606 Specificat

6、ion for High-Strength Zinc-Coated (Galva-nized) Steel Core Wire for Aluminum and Aluminum-Alloy Conductors, Steel ReinforcedB802/B802M Specification for Zinc5 % Aluminum-Mischmetal Alloy-Coated Steel Core Wire for AluminumConductors, Steel Reinforced (ACSR)B803 Specification for High-Strength Zinc5

7、%Aluminum-Mischmetal Alloy-Coated Steel Core Wire forUse in Overhead Electrical ConductorsE83 Practice for Verification and Classification of Exten-someter Systems3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 lotunless otherwise specified in the contract ororder, a lot shall

8、 consist of all coils or reels of strand of thesame diameter and unit lengths submitted for inspection at thesame time.3.1.2 production lotall of the wire spools loaded into astranding machine that are used to produce a completed strandcable.4. Ordering Information4.1 Orders for material under this

9、specification shall includethe following information:4.1.1 Length of each construction,4.1.2 Constructional description of stranded core (for ex-ample, 7 3 0.0943 in. or 19 3 0.0977 in.) (8.1 and 8.2),4.1.3 The multiple length of stranded core and the totalnumber of multiple lengths per reel, if all

10、owed (8.3 and Section15),4.1.4 Strength and coating type (Section 8),4.1.5 Direction of lay of outer layer (Section 7),4.1.6 Packaging (Section 15), and4.1.7 Place of inspection (Section 13).5. Material5.1 The coated steel wire used in the production of thestranded core shall, prior to stranding, me

11、et all of the require-ments of the appropriate specification that follows:5.1.1 Specification B498/B498M,5.1.2 Specification B606,5.1.3 Specification B802/B802M, and5.1.4 Specification B803.5.1.5 Specification B957.1This specification is under the jurisdiction of ASTM Committee B01 onElectrical Cond

12、uctors and is the direct responsibility of Subcommittee B01.05 onConductors of Ferrous Metals.Current edition approved Oct. 1, 2010. Published November 2010. Originallyapproved in 1969. Last previous edition approved in 2009 as B500/B500M 09.DOI: 10.1520/B0500_B0500M-10.2For referenced ASTM standard

13、s, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM Internat

14、ional, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.1.6 Specification B958.6. Joints6.1 There shall be no joints of any kind made in the finishedzinc-coated, zinc-5 % aluminum-mischmetal alloy-coated steelwires.7. Stranding7.1 The lay length of the 6-wire lay

15、er of 7 and 19-wirestranded core shall be not less than 16 or more than 26 timesthe outside diameter of the 6-wire layer. (Outside diameter isthree times nominal wire diameter.)7.2 The lay length of the 12-wire layer of a 19-wire strandedcore shall be not less than 14 or more than 22 times the outsi

16、dediameter of the 12-wire layer. (Outside diameter is five timesnominal wire diameter.)7.3 The lay length of the 18-wire layer of a 37-wire strandedcore shall be not less than 14 or more than 20 times the outsidediameter of the 18-wire layer. (Outside diameter is seven timesnominal wire diameter.)7.

17、4 The lay length of the 24-wire layer of a 61-wire strandedcore shall be not less than 14 or more than 18 times the outsidediameter of the 24-wire layer. (Outside diameter is nine timesnominal wire diameter.)7.5 The steel wires shall be so stranded that when thestranded core is cut the individual wi

18、res can be readilyregrouped and then held in place by one hand.7.6 For construction containing 19 or more wires, thedirection of lay will alternate with each layer.7.7 The direction of lay of the outer layer shall be asspecified by the purchaser at the time of placing the order.8. Construction and R

19、ecommended Standard Stranded-Core Lengths8.1 Overhead Electrical Conductors may be constructedusing steel core wire with any one of six types of protectivecoatings and associated strength grades. The acceptable corewires are produced to ASTM Specifications shown in Section5 of this standard.8.2 The

20、number and diameters of the steel wires shallconform to the requirements in respective ASTM ConductorStandards.8.3 Recommended standard unit-stranded-core multiplelengths are given in respective ASTM Conductor Standards.9. Length Tolerance9.1 All lengths of stranded core shall be furnished to alengt

21、h tolerance of 62%.10. Tensile Properties10.1 The rated ultimate strength or strength at 1 % exten-sion of stranded core for overhead electrical conductors shallbe taken as that percentage according to the number of wires,indicated below, of the sum of the strengths of the steel wires,calculated fro

22、m their specified nominal wire diameter and theappropriate specified minimum stress at 1 % extension orultimate strength given in Specifications B498/B498M, B606,B802/B802M, B803, B957,orB958:72wire strand96 % of sum of components192wire strand93 % of sum of components372wire strand91 % of sum of co

23、mponents612wire strand90 % of sum of components10.2 Stranded steel core samples shall sustain loads equal toor greater than the values computed by the method of 10.1.Compliance can be shown either by testing the completedstrand or by calculation using the strands individual wireproperties (e.g., ult

24、imate strength or stress at 1% extension).When calculating the strand strengths using the strandsindividual wire properties, it shall be computed as the percent-age of the sum of the actual wire strengths as indicated below:72wire strand96 % of sum of components192wire strand93 % of sum of component

25、s372wire strand91 % of sum of components612wire strand90 % of sum of components10.3 For determining compliance with the rated strength at1 % extension, use a Class B-1, B-2, or C extensometer asdescribed in Practice E83. The gage length shall be not lessthan 20 in. (500 mm).10.4 When testing the com

26、pleted stranded core strand,apply an initial load computed from the formula below andTable 1. Attach the extensometer and set to the appropriateInitial Setting from Table 1. Then increase the load until theindicated total extension is 1 % (0.0100 in./in. or 0.0100mm/mm). Record the load as the stren

27、gth at 1 % extension.Load 5 initial stress 3 number of wires in strand3 nominal wire diameter!23 0.7854.10.5 Stranded steel core shall meet the minimum require-ments for tensile strength at 1 % extension except as set forthin 10.6.10.6 Purchasers of core intended for use in conductorconstructions wi

28、th annealed aluminum wires, such as ACSS,may request the stranded steel core be compliant only withultimate tensile strength and may waive compliance with the 1% extension tensile requirement. This use of the ultimatetensile requirement as an alternate to the 1 % extensionrequirement shall be by agr

29、eement between the purchaser andproducer and shall be noted on product compliance documen-tation B498/B498M, B606, B802/B802M, B803, B957,orB958.TABLE 1 Initial Setting for Determining Stress at 1 % ExtensionNominal Wire Diameter Initial Stress Initial Setting of Extensometerin. mm psi kgf/mm2MPa in

30、./in. mm/mm0.05000.0899 1.2702.283 14 000 9.84 96.5 0.0005 0.00050.09000.1199 2.2863.045 28 000 19.7 193 0.0010 0.00100.12000.1899 3.0484.823 42 000 29.5 290 0.0015 0.0015B500/B500M 10211. Workmanship11.1 The finished stranded core shall be uniform in diameterand shall be free from imperfections not

31、 consistent with goodcommercial stranding practice. The stranded core shall be freefrom waviness and kinks.12. Number of Tests12.1 Samples from each lot shall be taken in accordancewith Table 2.Alot shall be defined as all the packages (reels orcoils) of the same size, construction, length, and type

32、 ofcoating offered for shipment at one time.12.2 An alternative to 12.1 is to use the strand productionlot. Testing would be completed on the individual wires,completed strand, or both, sampled to be representative of allstrand reels produced from that strand production lot. If theproducer makes thi

33、s election, the purchaser still reserves theright to test wires or strand from the offered lot as outlined in12.1. With this option, the producer shall report the test resultsof all reels in the shipment in lieu of using Table 2.12.3 Samples shall be tested for compliance with Sections 7and 10 and a

34、s required in the applicable wire standardreferenced in Section 2.13. Inspection13.1 All tests and inspection shall be made at the place offinal manufacture unless otherwise agreed upon between theproducer and the purchaser at the time of purchase.14. Rejection14.1 Failure of any of the test specime

35、ns to comply with therequirements of this specification shall constitute grounds forrejection of the lot represented by the specimen.The lot may beresubmitted for inspection by testing every package (reels orcoils) for the characteristic in which the specimen failed andsorting out the defective pack

36、ages.15. Packaging and Package Marking15.1 Package sizes and kind of package shall be agreedupon between the manufacturer and the purchaser.15.2 When permitted by the purchaser two or more unitlengths of stranded core may be shipped on one reel. If themultiple length is continuous, with no welds or

37、strand joints, aflag or marker shall be placed in the reel where the unit lengthends. If the multiple length on the reel consists of two or moreseparate lengths, they must not be joined. The free ends mustbe secured to the reel head, and a flag or warning marker shallbe inserted in the winding, warn

38、ing of the approaching end.15.3 The net weight, length or lengths, construction (strands3 wire diameter), direction of lay of outside layer, type of wirecoating, purchase order number, Specification B500/B500M,and manufacturers name shall be marked on a tag and attachedon the outside of the package.

39、 If multiple lengths are allowed,marking must show position and footage of each length andwhether “continuous or “separated lengths.16. Keywords16.1 metallic coated steel wire strand; steel core wirestrand; steel wire strandSUMMARY OF CHANGESCommittee B01 has identified the location of selected chan

40、ges to this standard since the last issue(B500/B500M 09) that may impact the use of this standard. (Approved Oct. 1, 2010.)(1) Add to Section 2 B957 and B958.(2) Add to Section 5: 5.1.5 Specification B957; 5.1.6 Specifi-cation B958.(3) Add to Section 10 the last sentence: B 498/B 498M, B 606,B 802/B

41、 802M, B 803, B957, or B958.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infr

42、ingement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standa

43、rd or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your vie

44、ws known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacti

45、ng ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 2 Number of SamplesNo. of Packages in Lot No. of Samples1to3 all4to30 3Over 30 10 %B500/B500M 103