ASTM B359 B359M-2002(2006) Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins《具有整体散热叶片的冷凝器及热交换器用铜及铜合金无缝管的标准规范》.pdf
《ASTM B359 B359M-2002(2006) Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins《具有整体散热叶片的冷凝器及热交换器用铜及铜合金无缝管的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM B359 B359M-2002(2006) Standard Specification for Copper and Copper-Alloy Seamless Condenser and Heat Exchanger Tubes With Integral Fins《具有整体散热叶片的冷凝器及热交换器用铜及铜合金无缝管的标准规范》.pdf(11页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B 359/B 359M 02 (Reapproved 2006)Standard Specification forCopper and Copper-Alloy Seamless Condenser and HeatExchanger Tubes With Integral Fins1This standard is issued under the fixed designation B 359/B 359M; the number immediately following the designation indicates the yearof origin
2、al adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Def
3、ense.1. Scope*1.1 This specification2establishes the requirements forseamless copper and copper alloy tubing on which the externalor internal surface, or both, has been modified by a cold-forming process to produce an integral enhanced surface forimproved heat transfer.1.2 UnitsThe values stated in
4、either in-pound units or SIunits are to be regarded separately as the standard. Within thetext, the SI units are shown in brackets. The values stated ineach system are not exact equivalents; therefore, each systemshall be used independently of the other. Combining valuesfrom the two systems could re
5、sult in nonconformance with thespecification.1.3 The tubes are typically used in surface condensers,evaporators, and heat exchangers.1.4 The product shall be produced of the following coppersor copper alloys, as specified in the ordering information.Copper or Copper AlloyUNS No.Type of MetalC10100 O
6、xygen-free electronicC10200 Oxygen-free without residual deoxidantsC10300 Oxygen-free, extra low phosphorusC10800 Oxygen-free, low phosphorusC12000 DLP Phosphorized, low residual phosphorus(See Note 1)C12200 DHP, Phosphorized, high residual phosphorus(See Note 1)C14200 DPA Phosphorized arsenical(See
7、 Note 1)C19200 Phosphorized, 1 % ironC23000 Red BrassC44300 Admiralty Metal Types B,C44400 C, andC44550 DC60800 Aluminum BronzeC68700 Aluminum Brass Type BC70400 95-5 Copper-NickelC70600 90-10 Copper-NickelC70620 90-10 Copper-Nickel (Modified for Welding)C71000 80-20 Copper-Nickel Type AC71500 70-30
8、 Copper-NickelC71520 70-30 Copper-Nickel (Modified for Welding)C72200 Copper-NickelNOTE 1Designations listed in Classification B 224.1.5 The following safety hazard caveat pertains only to thetest methods described in this specification. This standard doesnot purport to address all of the safety con
9、cerns, if any,associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.1.6 Product produced in accordance with the SupplementaryRequirements section for mili
10、tary applications shall be pro-duced only to the inch-pound system of this specification.2. Referenced Documents2.1 ASTM Standards:3B 153 Test Method for Expansion (Pin Test) of Copper andCopper-Alloy Pipe and TubingB 154 Test Method for Mercurous Nitrate Test for CopperAlloysB 170 Specification for
11、 Oxygen-Free Electrolytic CopperRefinery ShapesB 224 Classification of CoppersB 601 Classification for Temper Designations for Copperand Copper AlloysWrought and CastB 846 Terminology for Copper and Copper AlloysB 858 Test Method for Ammonia Vapor Test for Determin-ing Susceptibility to Stress Corro
12、sion Cracking in CopperAlloysB 900 Practice for Packaging of Copper and Copper AlloyMill Products for U.S. Government AgenciesD 4727/D 4727M Specification for Corrugated and SolidFiberboard Sheet Stock (Container Grade) and Cut ShapesE3 Guide for Preparation of Metallographic Specimens1This specific
13、ation is under the jurisdiction ofASTM Committee B05 on Copperand Copper Alloys and is the direct responsibility of Subcommittee B05.04 on Pipeand Tube.Current edition approved Oct. 1, 2006. Published October 2006. Originallyapproved in 1960. Last previous edition approved in 2002 as B 359/B 359M 02
14、.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SB-359 in Section II of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to
15、 the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.E8 Test Methods for Tension Testing of Metallic MaterialsE8M Te
16、st Methods for Tension Testing of Metallic Mate-rials MetricE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE53 Test Method for Determination of Copper in Unal-loyed Copper by GravimetryE62 Test Methods for Chemical Analysis of Copper andCopper Alloy
17、s (Photometric Methods)E112 Test Methods for Determining Average Grain SizeE118 Test Methods for Chemical Analysis of Copper-Chromium AlloysE 243 Practice for Electromagnetic (Eddy-Current) Exami-nation of Copper and Copper-Alloy TubesE 255 Practice for Sampling Copper and Copper Alloys forthe Deter
18、mination of Chemical CompositionE 478 Test Methods for Chemical Analysis of CopperAlloys3. General Requirements3.1 Product described by this specification shall typically befurnished with unenhanced ends, but may be furnished withenhanced ends or stripped ends from which the O.D. enhance-ment has be
19、en removed by machining.3.1.1 The enhanced sections of the tube in the as-fabricatedtemper are in the cold-worked condition produced by theenhancing operation.3.1.2 The unenhanced sections of the tube shall be in theannealed or light drawn temper, and shall be suitable forrolling-in operations.4. Te
20、rminology4.1 For the definitions of terms related to copper and copperalloys, refer to Terminology B 846.4.2 Definitions:4.2.1 flattening, vthis term shall be interpreted as thatcondition which allows a micrometer caliper, set at three timesthe wall thickness, to pass over the tube freely throughout
21、 theflattened part, except at the points where the change in elementof flattening takes place.4.3 Definitions of Terms Specific to This Standard:4.3.1 tube condenser, nsee tube, heat exchanger in Ter-minology B 846.5. Ordering Information5.1 Include the following information when placing ordersunder
22、 this specification:5.1.1 ASTM designation and year of issue,5.1.2 Copper or CopperAlloy UNS No. designation (see 1.4and Section 7),5.1.3 Temper (see Section 8),5.1.4 Dimensions: diameter, wall thickness, length and lo-cation of unenhanced surfaces and total tube length. Configu-ration of enhanced s
23、urfaces shall be as agreed upon betweenthe manufacturer and the purchaser. (See Figs. 1-3).5.1.5 Whether the product is to be subsequently welded forUNS Alloy C72200, UNS Alloys C 70620 and C71520 arewelding grades of C70600 and C71500,5.1.6 Quantity, and5.1.7 If product is for the U.S. government.5
24、.2 The following options are available and shall be speci-fied at the time of placing the order, when required:5.2.1 When heat identification or traceability is required,5.2.2 When tubes are for Boiler and Pressure Vessel codeapplication, which should then be ordered according to ASMESB 359,5.2.3 Fl
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB359B359M20022006STANDARDSPECIFICATIONFORCOPPERANDCOPPERALLOYSEAMLESSCONDENSERANDHEATEXCHANGERTUBESWITHINTEGRALFINS

链接地址:http://www.mydoc123.com/p-461021.html