ASTM B283-2011 Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)《铜及铜合金压模锻件(热压)的标准规格》.pdf
《ASTM B283-2011 Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)《铜及铜合金压模锻件(热压)的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM B283-2011 Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)《铜及铜合金压模锻件(热压)的标准规格》.pdf(10页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B283 11Standard Specification forCopper and Copper-Alloy Die Forgings (Hot-Pressed)1This standard is issued under the fixed designation B283; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A
2、 number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification establishes the requirements for
3、cop-per and copper alloy die forgings produced by the hot pressingmethod. The following copper and copper alloys are included:Copper or Copper AlloyUNS No. NameC11000 copperC14500 copper-telluriumC14700 copper-sulfurC27450 plumbing brassC36500 leaded Muntz metalC37000 free-cutting Muntz metalC37700
4、forging brassC46400 naval brassC48200 medium leaded naval brassC48500 leaded naval brassC49255 copper-zinc-bismuth-nickel alloyC49260 copper-zinc-bismuth alloyC49300 copper-zinc-tin-bismuth alloyC49340 copper-zinc-tin-bismuth alloyC49350 copper-zinc-tin-bismuth alloyC61900 aluminum bronzeC62300 alum
5、inum bronze, 9 %C63000 aluminum-nickel bronzeC63200 aluminum-nickel bronzeC64200 aluminum-silicon bronzeC64210 aluminum-silicon bronze, 6.7 %C65500 high-silicon bronze (A)C67500 manganese bronze (A)C67600 . . .C69300 copper-zinc-siliconC70620 copper-nickel 90-10C71520 copper-nickel 70-30C77400 nicke
6、l silver, 45-101.2 UnitsThe values stated in inch-pound units are to beregarded as standard. The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered standard.NOTE 1Nominal composition and relative forgeability ratings aregi
7、ven in Appendix X1. Copper-nickel alloys C70620 and C71520 areintended for welded applications with seawater exposure.NOTE 2Wrought product intended for hot forging is described inSpecification B124/B124M.1.3 The following safety caveat pertains only to Section 10of this specification. This standard
8、 does not purport to addressall of the safety concerns, if any, associated with its use. It isthe responsibility of the user of this standard to establishappropriate safety and health practices and determine theapplicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Stan
9、dards:2B124/B124M Specification for Copper and Copper AlloyForging Rod, Bar, and ShapesB249/B249M Specification for General Requirements forWrought Copper and Copper-Alloy Rod, Bar, Shapes andForgingsB846 Terminology for Copper and Copper AlloysE8/E8M Test Methods for Tension Testing of MetallicMate
10、rialsE62 Test Methods for Chemical Analysis of Copper andCopper Alloys (Photometric Methods)3E75 Test Methods for Chemical Analysis of Copper-Nickeland Copper-Nickel-Zinc Alloys3E478 Test Methods for ChemicalAnalysis of CopperAlloys2.2 Other Standards:ISO 7602 Determination of Tellurium Content (Hig
11、hContent)Flame Atomic Absorption SpectrometricMethod4JIS H 1068:2005 Method for Determination of Bismuth inCopper and Copper Alloys5(Japanese Industrial Stan-dards)2.3 Military Standards:MIL-STD-792 Identification Marking Requirements forSpecial Purpose Components61This specification is under the ju
12、risdiction ofASTM Committee B05 on Copperand Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod,Bar, Wire, Shapes and Forgings.Current edition approved Jan. 1, 2011. Published February 2011. Originallyapproved in 1953. Last previous edition approved in 2010 as B283 10a. DOI
13、:10.1520/B0283-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of th
14、is historical standard is referencedon www.astm.org.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.5Available from Japanese Industrial Standards, http:/www.JIS.or.jp/6Available from Standardization Documents Order Desk,
15、DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/www.dodssp.daps.mil.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.NAVSEA T9074-AS-GIB
16、-010/271 Requirements for Non-destructive Testing Method63. General Requirements3.1 The following sections of Specification B249/B249Mconstitute a part of this specification:3.1.1 Terminology,3.1.2 Materials and Manufacture,3.1.3 Workmanship, Finish and Appearance,3.1.4 Sampling,3.1.5 Number of Test
17、s and Retests,3.1.6 Specimen Preparation,3.1.7 Test Methods,3.1.8 Significance of Numerical Limits,3.1.9 Inspection,3.1.10 Rejection and Rehearing,3.1.11 Certification,3.1.12 Test Reports,3.1.13 Packaging and Package Marking, and3.1.14 Supplementary Requirements.3.1.15 In addition, when a section wi
18、th a title identical toone of those referenced in 3.1, above, appears in this specifi-cation, it contains additional requirements that supplementthose appearing in Specification B249/B249M.4. Terminology4.1 Definitions:4.1.1 For definitions of terms related to copper and copperalloys, refer to Termi
19、nology B846.4.2 Definition of Term Specific to This Standard:4.2.1 hot pressed forging, na product made by pressing aheated blank or section of wrought or cast copper or copperalloy in a closed impression die.5. Ordering Information5.1 Include the following information when placing ordersfor product
20、s to this specification, as applicable:5.1.1 ASTM designation and year of issue,5.1.2 Copper or Copper Alloy UNS No. designation(Scope),5.1.3 Drawing showing the shape dimensions and toler-ances (Dimensions and Permissible Variations),5.1.4 Temper (as specified herein),5.1.5 Quantity: total weight o
21、r number of pieces for eachform, temper, and copper or copper alloy,5.1.6 When product is purchased for agencies of the U.S.government (as specified herein), and5.1.7 When product must adhere to the requirements ofASME Boiler and Pressure Vessel Code (Mechanical PropertyRequirements).5.2 The followi
22、ng requirements are optional and shall bespecified in the contract or purchase order.5.2.1 Certification (as specified herein and SupplementaryRequirements),5.2.2 Mill test report (as specified in B249/B249M), and5.2.3 Ultrasonic inspection report (Supplementary Require-ments).6. Material and Manufa
23、cture6.1 Materials:6.1.1 The material of manufacture shall be a form of rods,billets, or blanks cut from cast or wrought material of one ofthe copper or copper alloys listed in the Scope of thisspecification and of purity and soundness as to be suitable forprocessing in to the products prescribed he
24、rein.6.1.2 In the event heat identification or traceability isrequired, the purchaser shall specify the details desired.NOTE 3Due to the discontinuous nature of the processing of castingsinto wrought products, it is not always practical to identify specific castinganalysis with a specific quantity o
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB2832011STANDARDSPECIFICATIONFORCOPPERANDCOPPERALLOYDIEFORGINGSHOTPRESSED 铜合金 锻件 热压 标准 规格 PDF

链接地址:http://www.mydoc123.com/p-460865.html