ASTM B159 B159M-2011 Standard Specification for Phosphor Bronze Wire《磷青铜线的标准规格》.pdf

《ASTM B159 B159M-2011 Standard Specification for Phosphor Bronze Wire《磷青铜线的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B159 B159M-2011 Standard Specification for Phosphor Bronze Wire《磷青铜线的标准规格》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B159/B159M 11Standard Specification forPhosphor Bronze Wire1This standard is issued under the fixed designation B159/B159M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last revision. A number in parenth

2、eses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification establishes the requirements forround, square and f

3、lat phosphor bronze wire of UNS AlloyNos. C51000, C52100, and C52400 for general and springapplications.1.1.1 Rectangular and square wire of the three alloys aregenerally available in sizes up to a maximum of 0.188 in. 5mm thick and 1.250 in. 32 mm wide.1.1.2 Round wire from Copper Alloy UNS No. C51

4、000 isgenerally available in sizes up to 0.500 in. 13 mm indiameter.1.2 UnitsValues stated in either inch-pound units or in SIunits are to be regarded separately as standard. Within the text,the SI units are shown in brackets. The values stated in eachsystem may not be exact equivalents; therefore,

5、each systemshall be used independently of the other. Combining valuesfrom the two systems may result in non-conformance with thespecification.1.3 Additional requirements for these products are estab-lished in Specification B250/B250M, see Section 3.1.4 This standard does not purport to address all o

6、f thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE 1It is to be understood that this specification is general. S

7、incethe product is used for many applications where the requirements of theoperations used are too particular to be specified by any of the ordinarymechanical tests, it is frequently advisable to submit samples or drawingsto the manufacturer and secure an adjustment of temper to suit the actualappli

8、cation for which the product is intended.NOTE 2Product in rod, bar and shape form is produced to Specifica-tion B139/B139M.2. Referenced Documents2.1 ASTM Standards:2B139/B139M Specification for Phosphor Bronze Rod, Bar,and ShapesB250/B250M Specification for General Requirements forWrought Copper Al

9、loy WireB601 Classification for Temper Designations for Copperand Copper AlloysWrought and CastB846 Terminology for Copper and Copper AlloysE8/E8M Test Methods for Tension Testing of MetallicMaterialsE62 Test Methods for Chemical Analysis of Copper andCopper Alloys (Photometric Methods)3E290 Test Me

10、thods for Bend Testing of Material for Duc-tilityE478 Test Methods for ChemicalAnalysis of CopperAlloys3. General Requirements3.1 The following sections of Specification B250/B250Mare a part of this specification:3.1.1 Terminology,3.1.2 Materials and Manufacture,3.1.3 Workmanship, Finish, and Appear

11、ance,3.1.4 Sampling,3.1.5 Number of Tests and Retests,3.1.6 Specimen Preparation,3.1.7 Test Methods,3.1.8 Significance of Numerical Limits,3.1.9 Inspection,3.1.10 Rejection and Rehearing,3.1.11 Certification,3.1.12 Mill Test Reports,1This specification is under the jurisdiction ofASTM Committee B05

12、on Copperand Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod,Bar, Wire, Shapes and Forgings.Current edition approved Oct. 1, 2011. Published November 2011. Originallyapproved in 1941. Last previous edition approved in 2005 as B159 05. DOI:10.1520/B0159_B0159M-11.2For ref

13、erenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is

14、referencedon www.astm.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.13 Packaging and Package Markings, and3.1.14 Supplementary Requirements.3.2 In addition,

15、when a section with a title identical to oneof those referenced in 3.1 appears in this specification, itcontains additional requirements which supplement those ap-pearing in Specification B250/B250M.4. Terminology4.1 Definitions specific to this standard:4.1.1 Cast, nThe maximum diameter of coiled w

16、ire whenone complete circumference rests completely on a flat surfaceas a table, workbench, or floor.4.1.2 Camber Offset, nThe axial component of curvatureof wire in an unrestrained state.NOTEThe camber is measured as the offset in the ends of oneturn of freely hanging wire.4.2 For other definitions

17、 of terms related to copper andcopper alloys, refer to Terminology B846.5. Ordering Information5.1 Include the following information when placing ordersfor product under this specification.5.1.1 ASTM designation and year of issue (for example,B159/B159M XX),5.1.2 Copper Alloy UNS No. (for example, C

18、51000),5.1.3 Temper designation (Section 8),5.1.4 Dimensions (diameter, distance between parallel sur-faces, and so forth),5.1.5 Type of edge (square corners, rounded corners, and soforth),5.1.6 How furnished (coil spool, reel, specific lengths, andso forth), and5.1.7 When product is purchased for a

19、gencies of the U.S.government (Section 11).5.2 The following options are available under this specifi-cation and shall be specified in the contract or purchase orderwhen required:5.2.1 Heat identification or traceability details,5.2.2 Certification,5.2.3 Mill Test Reports,5.2.4 Special packaging and

20、 package markings,5.2.5 Cast and camber offset requirements if specified.6. Materials and Manufacture6.1 Materials:6.1.1 The material of manufacturer shall be a casting billetof CopperAlloy UNS No. C51000, C52100, or C52400 of suchpurity and soundness as to be suitable for processing into theproduct

21、s prescribed herein.6.1.2 In the event heat identification or traceability isrequired, the purchaser shall specify the details desired.6.2 Manufacture:6.2.1 The product shall be manufactured by such hot-working, cold-working, and annealing processes as to producea uniform wrought structure in the fi

22、nished product.7. Chemical Composition7.1 The material shall conform to the chemical compositionrequirements of Table 1 for the Copper Alloy UNS No.specified in the ordering information.7.1.1 These composition limits do not preclude the presenceof other elements. When required, limits may be establi

23、shedand analysis required for unnamed elements by agreementbetween the supplier and the purchaser.7.2 Copper listed as the “remainder” is the differencebetween the sum of results for all elements determined and100 %.7.3 When all elements listed in Table 1are determined, thesum of results shall be 99

24、.5 % min.8. Temper8.1 Tempers, as defined in Classification B601, availableunder this specification are O61 (annealed), H01 (14 hard), H02(12 hard), H03 (34 hard), H04 (hard), H06 (extra hard), H08(spring), and H10 (extra spring).8.1.1 Tempers not covered by this specification shall be byagreement b

25、etween purchaser and supplier.NOTE 3The purchaser shall confer with the supplier for availability ofproduct in specific alloy, temper, form, and size.9. Mechanical Property Requirements9.1 Tensile Strength Requirements:9.1.1 When tested in accordance with Test Methods E8/E8M:9.1.1.1 Round and square

26、 wire for general applicationproduced from Copper Alloy UNS Nos. C51000, C52100, andC52400 shall conform to the requirements prescribed in Table2.9.1.1.2 Round or square wire produced from Copper AlloyUNS No. C51000 in H08 (spring) temper shall conform to therequirements prescribed in Table 3.9.1.1.

27、3 Rectangular wire produced from Copper Alloy UNSNos. C51000, C52100, and C52400 shall conform to therequirements prescribed in Table 4.10. Performance Requirements10.1 Bending Requirements:10.1.1 Wire in sizes up to 0.250 in. 7 mm inclusiveproduced from Copper Alloy UNS No. C51000 shall withstandbe

28、ing bent cold (room temperature) through an angle of 120on a radius equal to the diameter or distance between parallelsurfaces in accordance with Test Method E290. When so bent,tempers H08 and H10 shall not develop cracks or other flawsvisible to the unaided eye on the outside surface of the bend.TA

29、BLE 1 Chemical RequirementsCopper Alloy UNS No.C51000 C52100 C52400Composition, %Copper, incl silver remainder remainder remainderLead, max 0.05 0.05 0.05Iron, max 0.10 0.10 0.10Tin 4.25.8 7.09.0 9.011.0Zinc, max 0.30 0.20 0.20Phosphorus 0.030.35 0.030.35 0.030.35B159/B159M 11210.1.2 Other formabili

30、ty requirements, when specified, shallbe as agreed upon between purchaser and supplier.11. Purchases for U.S. Government11.1 Product purchased for agencies of the U.S. governmentshall conform to the additional requirements prescribed in theSupplementary Requirements section of Specification B250/B25

31、0M (see Section 11).12. Dimensions, Mass, and Permissible Variations12.1 The dimensions and tolerances for product produced tothis specification shall be as specified in the following tablesand related paragraphs or specified titles found in SpecificationB250/B250M:12.1.1 Diameter or Distance Betwee

32、n Parallel SurfacesTable 2.12.1.1.1 ThicknessTable 4.12.1.1.2 WidthTable 6.12.1.1.3 Length (Flat Wire Product)Tables 7 and 8.12.1.1.4 Straightness (Flat Wire Product) Table 9.12.1.1.5 Edge ContoursEdge Contour section.12.1.1.6 Corner RadiusFigure 4.13. Cast and Camber Offset13.1 When specified, the

33、requirements and method shall beas agreed upon between purchaser and supplier.14. Test Methods14.1 Chemical Analysis:14.1.1 Product composition shall, in case of dispute, bedetermined as follows:Element Test MethodsCopper E478Phosphorus E62Lead E478 (AA)Iron E478Zinc E478 (Titrimetric)Tin E47814.1.2

34、 Test method(s) to be followed for the determinationof elements required by contractual or purchase order agree-ment shall be as agreed upon between the supplier and thepurchaser.15. Keywords15.1 phosphor bronze alloy wire; UNS No. C51000 wire;UNS No. C52100 wire; UNS No. C52400 wireTABLE 2 Mechanic

35、al Requirements for Round or Square Wire forGeneral PurposesTemper Tensile Strength, ksi MpaAStandard NameCopper Alloy UNS No.C51000 C52100 C52400O61 annealed 48.063.033043553.068.036547060.075.0415515H01 quarter-hard 60.076.041552574.091.051062583.0102.0570705H02 half-hard 80.097.055067095.0115.065

36、5795108.0129.0745890H03 three-quarter-hard 96.0115.0660795113.0135.0780930125.0148.08601020H04 hard 108.0128.0745885125.0150.08601035135.0160.09301105H08 spring see Table 3 . .Aksi = 1000 psi.TABLE 3 Mechanical Requirements for H08 (Spring Temper) UNSNo. C51000 Round or Square WireDiameter or Distan

37、ce BetweenParallel Surfaces, in. mmTensile Strength, min, ksiMpaAElongation in 2 in.50 mm min, %0.025 0.60 and under 145.0 1000 .Over 0.025 to 0.06250.060 to 1.6135.0 930 .Over 0.0625 to 0.125 1.6 to 3.0 130.0 895 .Over 0.125 to 0.250 3.0 to 6.0 125.0 860 .Over 0.250 to 0.375 6.0 to 10 120.0 825 5.0

38、Over 0.375 to 0.50010 to 16, incl105.0 725 9.0Aksi = 1000 psi.TABLE 4 Mechanical Requirements for Flat Wire (Other ThanSquare Wire)Temper Tensile Strength, ksiAStandard NameCopper Alloy UNS No.C51000 C52100 C52400O61 annealed 435829540053673654605873400505H02 half-hard 587340050569844755807691525625

39、H04 hard 76915256258510058569094109650750H06 extra hard 8810360571097112670770107122740840H08 spring 95110655760105119725820115129795890H10 extra spring 100114690785116122800840120133825915Aksi = 1000 psi.B159/B159M 113SUMMARY OF CHANGESCommittee B05 has identified the location of selected changes t

40、o this standard since the last issue (B159 05)that may impact the use of this standard. (Approved Oct. 1, 2011.)(1) Minor editing throughout.(2) As noted some of the Metric Values were changed in Table2, 3 and 4.(3) Changed tensile range values for O61 temper for C51000to 48.0-63.0 ksi.(4) Added def

41、inition of “cast” and “camber offset” to Termi-nology sections.(5) Added option of specifying “Cast” and “Camber Offset” toSections 5 and 12.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this

42、 standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five year

43、s andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committ

44、ee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428

45、-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).B159/B159M 114