ASTM B152 B152M-2013 Standard Specification for Copper Sheet Strip Plate and Rolled Bar《铜片、铜带、铜板和轧制铜条的标准规格》.pdf
《ASTM B152 B152M-2013 Standard Specification for Copper Sheet Strip Plate and Rolled Bar《铜片、铜带、铜板和轧制铜条的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM B152 B152M-2013 Standard Specification for Copper Sheet Strip Plate and Rolled Bar《铜片、铜带、铜板和轧制铜条的标准规格》.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B152/B152M 09 B152/B152M 13 Used in USDOE-NE standardsStandard Specification forCopper Sheet, Strip, Plate, and Rolled Bar1This standard is issued under the fixed designation B152/B152M; the number immediately following the designation indicates the yearof original adoption or, in the c
2、ase of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This sp
3、ecification2 establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the followingcoppers.CopperUNS No.APreviousDesignation Type of CopperC10100B OFE Oxygen-free electronicC10200B OF Oxygen-free without residualdeoxidantsC10300 . Oxygen-free extra low phosphorusC104
4、00, C10500, C10700 OFS Oxygen-free, silver bearingC10800 . Oxygen-free low phosphorusC10910 . Low oxygenC11000B,C ETP,TPCElectrolytic tough pitchC , ToughpitchCC11300, C11400, C11600B STP Silver bearing tough pitchC12000 DLP Phosphorized, low residual phos-phorusC12200B DHP Phosphorized, high residu
5、al phos-phorusC12300 DPS Phosphorized, silver bearingC14200 DPA Phosphorus deoxidized, arsenicalC14420 . Tin bearing tellurium copperC14530 . Tin tellurium bearing copper_A Except Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus deoxidized, arsenical), C14420 (tin bearing tellurium), and C145
6、30 (tin tellurium bearing) thesetypes of copper are classified in Classification B224.B SAE Specification CA101 conforms to Copper UNS No. C10100; SAE Specification CA102 conforms to the requirements for Copper UNS No. C10200; SAE SpecificationCA110 conforms to the requirements for Copper UNS No. C1
7、1000; SAE Specifications CA113, CA114, and CA116 conform to the requirements for Copper UNS Nos.C11300, C11400, and C11600; SAE Specification CA120 conforms to Copper UNS No. C12000; and SAE Specification CA122 conforms to the requirements for CopperUNS No. C12200.CUnless specified in the contract o
8、r purchase order the supplier is permitted to provide ETP copper or TP copper.NOTE 1Each of the coppers listed has unique properties that can make it suitable for specific applications. The purchaser should consult with thesupplier to determine which copper would be best suited for the intended appl
9、ication.NOTE 2This specification is not intended to establish requirements for material rolled to ounce-weight thicknesses. Such material is defined inSpecification B370.Plates for locomotive fireboxes are defined in Specification B11.Flat copper products with finished (rolled or drawn) edges (flat
10、wire and strip) are defined in Specification B272.1.1.1 When a specific copper is not identified in the contract or purchase order, the supplier may furnish product from any ofthe listed coppers.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. T
11、he values stated in eachsystem may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from thetwo systems may result in non-conformance with the standard.1 This specification is under the jurisdiction of ASTM Committee B05 on Copper and Copper
12、 Alloys and is the direct responsibility of Subcommittee B05.01 on Plate,Sheet, and Strip.Current edition approved Oct. 1, 2009Jan. 15, 2013. Published November 2009January 2013. Originally approved in 1942. Last previous edition approved in 20062009as B152/B152M 06aB152/B152M 09.1. DOI: 10.1520/B01
13、52_B0152M-09.10.1520/B0152_B0152M-13.2 For ASME Boiler and Pressure Vessel Code applications see related Specification SB-152 in Section 11 of that Code.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to
14、the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summar
15、y of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States11.3 The following safety hazards caveat only pertains to the test method portion, Section 13 of this specification:This standarddo
16、es not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Stan
17、dards:3B11 Specification for Copper Plates for Locomotive Fireboxes (Withdrawn 1980)4B170 Specification for Oxygen-Free Electrolytic CopperRefinery ShapesB193 Test Method for Resistivity of Electrical Conductor MaterialsB216 Specification for Tough-Pitch Fire-Refined CopperRefinery ShapesB224 Classi
18、fication of CoppersB248 Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled BarB248M Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar(Metric)B272 Specification for Copper Flat Product
19、s with Finished (Rolled or Drawn) Edges (Flat Wire and Strip)B370 Specification for Copper Sheet and Strip for Building ConstructionB577 Test Methods for Detection of Cuprous Oxide (Hydrogen Embrittlement Susceptibility) in CopperB601 Classification for Temper Designations for Copper and Copper Allo
20、ysWrought and CastB846 Terminology for Copper and Copper AlloysE3 Guide for Preparation of Metallographic SpecimensE8 Test Methods for Tension Testing of Metallic MaterialsE8M Test Methods for Tension Testing of Metallic Materials Metric (Withdrawn 2008)4E53 Test Method for Determination of Copper i
21、n Unalloyed Copper by GravimetryE62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods) (Withdrawn 2010)4E112 Test Methods for Determining Average Grain SizeE478 Test Methods for Chemical Analysis of Copper AlloysE527 Practice for Numbering Metals and Alloys in the U
22、nified Numbering System (UNS)2.2 ASME Standard:ASME Boiler Pressure Vessel Code53. General Requirements3.1 The following sections of Specification B248 or B248M constitute a part of this specification.3.1.1 Terminology.3.1.2 Materials and Manufacture.3.1.3 Sampling.3.1.4 Number of Tests and Retests.
23、3.1.5 Specimen Preparation.3.1.6 Test Methods.3.1.7 Packaging and Package Marking.3.1.8 Workmanship, Finish, and Appearance.3.1.9 Significance of Numerical Limits.3.1.10 Rejection and Rehearing.3.2 In addition, when a section with a title identical to that referenced in 3.1 appears in this specifica
24、tion, it contains additionalrequirements which supplement those appearing in Specification B248 or B248M.4. Terminology4.1 DefinitionsTerms used in this specification are in accordance with Terminology B846 and Specifications B248 andB248M.4.2 Definitions of Terms Specific to This Standard:4.2.1 cap
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB152B152M2013STANDARDSPECIFICATIONFORCOPPERSHEETSTRIPPLATEANDROLLEDBAR 铜片 铜板 轧制 标准 规格 PDF

链接地址:http://www.mydoc123.com/p-460459.html