ASTM B152 B152M-2006a Standard Specification for Copper Sheet Strip Plate and Rolled Bar.pdf
《ASTM B152 B152M-2006a Standard Specification for Copper Sheet Strip Plate and Rolled Bar.pdf》由会员分享,可在线阅读,更多相关《ASTM B152 B152M-2006a Standard Specification for Copper Sheet Strip Plate and Rolled Bar.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: B 152/B 152M 06aUsed in USDOE-NE standardsStandard Specification forCopper Sheet, Strip, Plate, and Rolled Bar1This standard is issued under the fixed designation B 152/B 152M; the number immediately following the designation indicates the yearof original adoption or, in the case of rev
2、ision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specificati
3、on2establishes the requirements for cop-per sheet, strip, plate, and rolled bar produced from thefollowing coppers.CopperUNS No.APreviousDesigna-tionType of CopperC10100BOFE Oxygen-free electronicC10200BOF Oxygen-free without residualdeoxidantsC10300 . Oxygen-free extra low phosphorusC10400, C10500,
4、 C10700 OFS Oxygen-free, silver bearingC10800 . Oxygen-free low phosphorusC10910 . Low oxygenC11000BETP Electrolytic tough pitchC11300, C11400, C11600BSTP Silver bearing tough pitchC12000 DLP Phosphorized, low residual phos-phorusC12200BDHP Phosphorized, high residual phos-phorusC12300 DPS Phosphori
5、zed, silver bearingC14200 DPA Phosphorus deoxidized, arsenicalC14420 . Tin bearing tellurium copperC14530 . Tin tellurium bearing copper_AExcept Copper UNS Nos. C10910 (low oxygen), C14200 (phosphorus deoxi-dized, arsenical), C14420 (tin bearing tellurium), and C14530 (tin telluriumbearing) these ty
6、pes of copper are classified in Classification B 224.BSAE Specification CA101 conforms to Copper UNS No. C10100; SAESpecification CA102 conforms to the requirements for Copper UNS No. C10200;SAE Specification CA110 conforms to the requirements for Copper UNS No.C11000; SAE Specifications CA113, CA11
7、4, and CA116 conform to the require-ments for Copper UNS Nos. C11300, C11400, and C11600; SAE SpecificationCA120 conforms to Copper UNS No. C12000; and SAE Specification CA122conforms to the requirements for Copper UNS No. C12200.NOTE 1Each of the coppers listed has unique properties that can makeit
8、 suitable for specific applications. The purchaser should consult with thesupplier to determine which copper would be best suited for the intendedapplication.NOTE 2This specification is not intended to establish requirements formaterial rolled to ounce-weight thicknesses. Such material is defined in
9、Specification B 370.Plates for locomotive fireboxes are defined in Specification B11.Flat copper products with finished (rolled or drawn) edges (flat wire andstrip) are defined in Specification B 272.1.1.1 When a specific copper is not identified in the contractor purchase order, the supplier may fu
10、rnish product from any ofthe listed coppers.1.2 The values stated in inch-pound or SI units are to beregarded separately as standard. The values in each system arenot exact equivalents; therefore, each system shall be usedindependently of the other. Combining values from the twosystems may result in
11、 nonconformance with the specification.1.3 The following safety hazards caveat only pertains to thetest method portion, Section 13 of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this s
12、tandard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:3B11 Specification for Copper Plates for Locomotive Fire-boxes4B 170 Specification for Oxygen-Free Electrolytic CopperRefinery
13、 ShapesB 193 Test Method for Resistivity of Electrical ConductorMaterialsB 216 Specification for Tough-Pitch Fire-Refined CopperRefinery ShapesB 224 Classification of CoppersB 248 Specification for General Requirements for WroughtCopper and Copper-Alloy Plate, Sheet, Strip, and RolledBarB 248M Speci
14、fication for General Requirements forWrought Copper and Copper-Alloy Plate, Sheet, Strip, andRolled Bar MetricB 272 Specification for Copper Flat Products with Finished(Rolled or Drawn) Edges (Flat Wire and Strip)1This specification is under the jurisdiction ofASTM Committee B05 on Copperand CopperA
15、lloys and is the direct responsibility of Subcommittee B05.01 on Plate,Sheet, and Strip.Current edition approved Oct. 1, 2006. Published October 2006. Originallyapproved in 1942. Last previous edition approved in 2006 as B 152/B 152M 06.2For ASME Boiler and Pressure Vessel Code applications see rela
16、ted Specifi-cation SB-152 in Section 11 of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Withdra
17、wn.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.B 370 Specification for Copper Sheet and Strip for BuildingConstructionB 577 Test Methods for Detection of Cuprous O
18、xide (Hy-drogen Embrittlement Susceptibility) in CopperB 601 Classification for Temper Designations for Copperand Copper AlloysWrought and CastB 846 Terminology for Copper and Copper AlloysE3 Guide for Preparation of Metallographic SpecimensE8 Test Methods for Tension Testing of Metallic MaterialsE8
19、M Test Methods for Tension Testing of Metallic Mate-rials MetricE53 Test Method for Determination of Copper in Unal-loyed Copper by GravimetryE62 Test Methods for Chemical Analysis of Copper andCopper Alloys (Photometric Methods)E112 Test Methods for Determining Average Grain SizeE 478 Test Methods
20、for Chemical Analysis of CopperAlloysE 527 Practice for Numbering Metals and Alloys (UNS)2.2 ASME Standard:ASME Boiler Pressure Vessel Code53. General Requirements3.1 The following sections of Specification B 248 orB 248M constitute a part of this specification.3.1.1 Terminology.3.1.2 Materials and
21、Manufacture.3.1.3 Sampling.3.1.4 Number of Tests and Retests.3.1.5 Specimen Preparation.3.1.6 Test Methods.3.1.7 Packaging and Package Marking.3.1.8 Workmanship, Finish, and Appearance.3.1.9 Significance of Numerical Limits.3.1.10 Rejection and Rehearing.3.2 In addition, when a section with a title
22、identical to thatreferenced in 3.1 appears in this specification, it containsadditional requirements which supplement those appearing inSpecification B 248 or B 248M.4. Terminology4.1 DefinitionsTerms used in this specification are inaccordance with Terminology B 846 and Specifications B 248and B 24
23、8M.4.2 Definitions of Terms Specific to This Standard:4.2.1 capable ofthe test need not be performed by theproducer of the material. However, should subsequent testingby the purchaser establish that the material does not meet theserequirements the material shall be subject to rejection.5. Ordering I
24、nformation5.1 Orders for products under this specification shallinclude the following:5.1.1 ASTM specification designation and year of issue,5.1.2 Quantity,5.1.3 Copper UNS No. (Section 1). When Alloys C10400,C10500, C10700, C11300, C11400, C11600, or C12300, theamount of silver in ounces per ton,5.
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMB152B152M2006ASTANDARDSPECIFICATIONFORCOPPERSHEETSTRIPPLATEANDROLLEDBARPDF
链接地址:http://www.mydoc123.com/p-460456.html