ASTM B140 B140M-2012(2017) Standard Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod Bar and Shapes《铜锌铅(红黄铜或五金青铜)棒材 杆材和型材的标准规格》.pdf

《ASTM B140 B140M-2012(2017) Standard Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod Bar and Shapes《铜锌铅(红黄铜或五金青铜)棒材 杆材和型材的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM B140 B140M-2012(2017) Standard Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod Bar and Shapes《铜锌铅(红黄铜或五金青铜)棒材 杆材和型材的标准规格》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: B140/B140M 12 (Reapproved 2017)Standard Specification forCopper-Zinc-Lead (Red Brass or Hardware Bronze) Rod,Bar, and Shapes1This standard is issued under the fixed designation B140/B140M; the number immediately following the designation indicates the yearof original adoption or, in the

2、 case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1

3、This specification establishes the requirements forcopper-zinc-lead (leaded red brass or hardware bronze) rod,bar, and shapes of UNS Copper Alloy Nos. C31400, C31600,and C32000 available for general and screw machine applica-tions.1.2 UnitsValues stated in either inch-pound units or SIunits are to b

4、e regarded separately as standard. Within the text,SI units are shown in brackets. The values in each system maynot be exact equivalents; therefore, each system shall be usedindependently of the other. Combining values from the twosystems may result in nonconformance with the specification.1.3 This

5、international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (T

6、BT) Committee.2. Referenced Documents2.1 ASTM Standards:2B249/B249M Specification for General Requirements forWrought Copper and Copper-Alloy Rod, Bar, Shapes andForgingsB601 Classification for Temper Designations for Copper andCopper AlloysWrought and CastB846 Terminology for Copper and Copper Allo

7、ysE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE62 Test Methods for Chemical Analysis of Copper andCopperAlloys (Photometric Methods) (Withdrawn 2010)3E478 Test Methods for Chemical Analysis of Copper Alloys3. General Requirements3.1 The following sections of Specification B249/B249

8、Mconstitute a part of this specification:3.1.1 Terminology (B846),3.1.2 Materials and Manufacture,3.1.3 Workmanship, Finish, and Appearance,3.1.4 Sampling,3.1.5 Number of Tests and Retests,3.1.6 Specimen Preparation,3.1.7 Test Methods,3.1.8 Significance of Numerical Limits,3.1.9 Inspection,3.1.10 Re

9、jection and Rehearing,3.1.11 Certification,3.1.12 Test Report,3.1.13 Product Marking,3.1.14 Packaging and Package Marking, and3.1.15 Supplementary Requirements.3.2 In addition, when a section with a title identical to oneof those referenced in 3.1 appears in this specification, itcontains additional

10、 requirements which supplement those ap-pearing in Specification B249/B249M.4. Ordering Information4.1 Include the following specified choices when placingorders for products under this specification, as applicable:4.1.1 ASTM designation and year of issue,4.1.2 Copper Alloy UNS No. designation (Scop

11、e),4.1.3 Temper designation (Temper Section),4.1.4 Dimensionsdiameter, distance between parallelsurfaces,4.1.5 How furnished; length, specific or stock, with orwithout ends,4.1.6 Quantity; total weight or length, or number of piecesof each temper, form, and alloy, and1This specification is under the

12、 jurisdiction ofASTM Committee B05 on Copperand Copper Alloys and is the direct responsibility of Subcommittee B05.02 on Rod,Bar, Wire, Shapes and Forgings.Current edition approved April 1, 2017. Published April 2017. Originallyapproved in 1941. Last previous edition approved in 2012 as B140/B140M 1

13、2.DOI: 10.1520/B0140_B0140M-12R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3The last approved version

14、of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with inte

15、rnationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.14.1.7 Intended application, general use or auto

16、matic screwmachine use (Straightness Tolerance).4.2 The following options are available but may not beincluded unless specified at the time of placing of the orderwhen required:4.2.1 Certification (Specification B249/B249M),4.2.2 Mill Test Reports (Specification B249/B249M), and4.2.3 If product is p

17、urchased for agencies of the U.S.Government (Specification B249/B249M).5. Material and Manufacture5.1 Material:5.1.1 The material of manufacture shall be a form (castbillets, logs, or rods) of Copper Alloy UNS Nos. C31400,C31600, or C32000 of such purity and soundness as to besuitable for processing

18、 into the products prescribed herein.5.2 Manufacture:5.2.1 The product shall be manufactured by such hotworking, cold working, straightening, and annealing processesas to produce a uniform wrought structure in the finishedproduct.6. Chemical Composition6.1 The material shall conform to the chemical

19、compositionrequirements in Table 1 for the Copper Alloy UNS No.designation specified in the ordering information.6.1.1 These composition limits do not preclude the presenceof other elements. By agreement between the manufacturer andthe purchaser, limits may be established and analysis requiredfor un

20、named elements.6.2 For alloys in which zinc is listed as the “remainder,”either copper or zinc may be taken as the difference betweenthe sum of results of all other elements determined and 100 %.When copper is so determined, that difference value shallconform to the requirements given in Table 1.6.3

21、 When all elements in Table 1 are determined, the sum ofthe results shall be 99.6 % minimum.7. Temper7.1 The standard tempers, as defined in Classification B601,for products described in this specification are O60 (softanneal), H02 (half-hard), and H04 (hard).8. Mechanical Property Requirements8.1 T

22、ensile Strength Requirements:8.1.1 Product furnished under this specification shall con-form to the tensile requirements prescribed in Table 2 (inch-pound units) or Table 3 (SI units) when tested in accordancewith Test Methods E8/E8M.9. Dimensions, Mass and Permissible Variations9.1 The dimensions a

23、nd tolerances for product described bythis specification shall be as specified in Specification B249/B249M with particular reference to the following tables andrelated paragraphs:9.2 Diameter or Distance Between Parallel Surfaces:9.2.1 RodRefer to Table 1 for round, hexagonal and oc-tagonal rod.9.2.

24、2 BarRefer to Table 8 for thickness and Table 10 forwidth.9.3 LengthRefer to Tables 13 and 14.9.4 StraightnessRefer to Table 16. General use or auto-matic screw machine use as chosen in the purchase order.9.5 ShapesThe dimensional tolerances for shapes shall beagreed upon between the manufacturer or

25、 supplier and thepurchaser and shall be specified in the order or purchasecontract.10. Test Methods10.1 Chemical Analysis:10.1.1 In cases of disagreement, test methods for chemicalanalysis shall be subject to agreement between the manufac-turer or supplier and the purchaser.10.1.2 The following tabl

26、e is a list of published testmethods, some of which are considered by ASTM as no longerviable. These and others not listed may be used subject toagreement.Element ASTM Test MethodCopper E478Lead E478, atomic absorptionIron E478Nickel E478, photometricPhosphorus E62Zinc E478, Titrimetric11. Keywords1

27、1.1 C31400; C31600; C32000; hardware bronze; hardwarebronze rod; hardware bronze shapes; leaded brass shapes;leaded red brass bar; leaded red brass rodTABLE 1 Chemical RequirementsElementComposition, %Copper Alloy UNS No.C31400 C31600 C32000Copper 87.5 to 90.5 87.5 to 90.5 83.5 to 86.5Lead 1.3 to 2.

28、5 1.3 to 2.5 1.5 to 2.2Iron, max 0.10 0.10 0.10Nickel 0.7 max 0.7 to 1.2 0.25 maxZinc remainder remainder remainderPhosphorus . 0.04 to 0.10 .B140/B140M 12 (2017)2SUMMARY OF CHANGESCommittee B05 has identified the principal changes to this specification that have been incorporated since the2007 issu

29、e as follows:(1) Changes made to conform to the ASTM Form and Style andB950 guidelines.TABLE 2 Tensile Requirements (Inch-Pound Units)Copper AlloyUNS No.Temper DesignationDiameter or Distance BetweenParallel Surfaces, in.Width, in.TensileStrength,min, ksiYield Strengthat 0.5 %ExtensionUnder Load,min

30、, ksiElongation in4 Diameteror Thickness ofSpecimenmin, %ACode NameC31400, C31600,C32000O60 soft anneal all forms all sizes . 35 10 25C31400, C31600,C32000HO2 half hard rod:12 and under . 50 30 7over12 to 1 . 45 27 10over 1 . 40 25 12bar: 1 and under 2 and under 40 25 12over 1 over 2 40B25B12BC31400

31、 H04 hard rod 2 and under . 53 40 6C31600, C32000 H04 hard rod 2 and under . 60 50 6bar 1 and under 2 and under 60 50 6AIn any case, a minimum gage length of 1 in. shall be used.BIn the case of bars either over 1 in. in thickness or over 2 in. in width, or both, these values shall apply.TABLE 3 Tens

32、ile Requirements (SI Units)Copper AlloyUNS No.Temper DesignationDiameter or Distance BetweenParallel Surfaces, mmWidth, mmTensileStrength,min MPaYield Strengthat 0.5 %ExtensionUnder Load,min, MPaElongationAmin, %Code NameC31400, C31600,C32000O60 Soft anneal all forms all sizes . 240 70 25C31400, C31

33、600,C32000HO2 half hard rod: 12 and under . 345 205 7over 12 to 25 . 310 185 10over 25 . 275 170 12bar: 25 and under 50 and under 275 170 12over 25 over 50 275B170B12BC31400 H04 hard rod 50 and under . 365 275 6C31600, C32000 H04 hard rod 50 and under . 415 345 6bar 25 and under 50 and under 415 345

34、 6AElongation values are based on a gage length of 5.65 times the square root of the area for dimensions greater than 2.5 mm.BIn the case of bars either over 25 mm in thickness or over 50 mm in width, or both, these values shall apply.B140/B140M 12 (2017)3ASTM International takes no position respect

35、ing the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This stan

36、dard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Internatio

37、nal Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.

38、This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 12 (2017)4