ASTM A830 A830M-2014 Standard Specification for Plates Carbon Steel Structural Quality Furnished to Chemical Composition Requirements《按照化学成分要求提供的碳素结构质量钢板标准规格》.pdf

《ASTM A830 A830M-2014 Standard Specification for Plates Carbon Steel Structural Quality Furnished to Chemical Composition Requirements《按照化学成分要求提供的碳素结构质量钢板标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM A830 A830M-2014 Standard Specification for Plates Carbon Steel Structural Quality Furnished to Chemical Composition Requirements《按照化学成分要求提供的碳素结构质量钢板标准规格》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A830/A830M 14Standard Specification forPlates, Carbon Steel, Structural Quality, Furnished toChemical Composition Requirements1This standard is issued under the fixed designation A830/A830M; the number immediately following the designation indicates the yearof original adoption or, in t

2、he case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers structural quality carbon steelplates furnished to chemica

3、l composition requirements.1.2 The plates are available in several standard steel gradesand non-standard grades.1.3 The plates are usually furnished in the as-rolled (hot-rolled) condition.1.4 Supplementary requirements are provided for additionalrequirements that may be specified on the order.1.5 W

4、hen the steel is to be welded, it is presupposed that awelding procedure suitable for the grade of steel and intendeduse or service will be utilized. See Appendix X3 of Specifica-tion A6/A6M for information on weldability.1.6 The values stated in either SI units or inch-pound unitsare to be regarded

5、 separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.2. Referenced Documents2.1 ASTM Standards:2A6/A6M Specification f

6、or General Requirements for RolledStructural Steel Bars, Plates, Shapes, and Sheet Piling3. Ordering Information3.1 In addition to the information required by SpecificationA6/A6M, the order shall include the following, if applicable:3.1.1 Silicon requirements (see 5.3 and Supplementary Re-quirement

7、S96), and3.1.2 Limitation on rimmed or capped steel.4. Materials and Manufacture4.1 The steel shall be killed.5. Chemical Composition5.1 The heat analysis shall conform to the requirements forthe applicable grade listed in Table 1, unless otherwise speci-fied as permitted in 5.2.5.2 The chemical req

8、uirements for heat analysis may bespecified in accordance with the ranges and limits listed inTable 2. In such instances, the heat analysis shall conform tothe requirements specified on the order.5.3 When silicon is required, the range on heat analysis shallbe from 0.15 to 0.40 % unless otherwise sp

9、ecified on the order(see Supplementary Requirement S96).6. General Requirements6.1 Material furnished under this specification shall con-form to the requirements of the current edition of SpecificationA6/A6M, for the ordered material, unless a conflict exists inwhich case this specification shall pr

10、evail.7. Keywords7.1 carbon; chemical composition; non-standard grades;plates; standard grades; steel; structural steel1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.02 on Structural

11、Steel for Bridges, Buildings, Rolling Stock and Ships.Current edition approved May 1, 2014. Published May 2014. Originallyapproved in 1984. Last previous edition approved in 2013 as A830/A830M 13.DOI: 10.1520/A0830_A0830M-14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcon

12、tact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West

13、Conshohocken, PA 19428-2959. United States1TABLE 1 Carbon Plate Compositions, Standard SteelsAGrade Chemical Composition Limits, %Number Carbon Manganese Phosphorous, max Sulfur, max1006 0.08 max 0.45 max 0.030 0.0301008 0.10 max 0.50 max 0.030 0.0301009 0.15 max 0.60 max 0.030 0.0301010 0.08 to 0.1

14、3 0.30 to 0.60 0.030 0.0301012 0.10 to 0.15 0.30 to 0.60 0.030 0.0301015 0.13 to 0.18 0.30 to 0.60 0.030 0.0301016 0.13 to 0.18 0.60 to 0.90 0.030 0.0301017 0.15 to 0.20 0.30 to 0.60 0.030 0.0301018 0.15 to 0.20 0.60 to 0.90 0.030 0.0301019 0.15 to 0.20 0.70 to 1.00 0.030 0.0301020 0.18 to 0.23 0.30

15、 to 0.60 0.030 0.0301021 0.18 to 0.23 0.60 to 0.90 0.030 0.0301022 0.18 to 0.23 0.70 to 1.00 0.030 0.0301023 0.20 to 0.25 0.30 to 0.60 0.030 0.0301025 0.22 to 0.28 0.30 to 0.60 0.030 0.0301026 0.22 to 0.28 0.60 to 0.90 0.030 0.0301030 0.28 to 0.34 0.60 to 0.90 0.030 0.0301033 0.30 to 0.36 0.70 to 1.

16、00 0.030 0.0301035 0.32 to 0.38 0.60 to 0.90 0.030 0.0301037 0.32 to 0.38 0.70 to 1.00 0.030 0.0301038 0.35 to 0.42 0.60 to 0.90 0.030 0.0301039 0.37 to 0.44 0.70 to 1.00 0.030 0.0301040 0.37 to 0.44 0.60 to 0.90 0.030 0.0301042 0.40 to 0.47 0.60 to 0.90 0.030 0.0301043 0.40 to 0.47 0.70 to 1.00 0.0

17、30 0.0301045 0.43 to 0.50 0.60 to 0.90 0.030 0.0301046 0.43 to 0.50 0.70 to 1.00 0.030 0.0301049 0.46 to 0.53 0.60 to 0.90 0.030 0.0301050 0.48 to 0.55 0.60 to 0.90 0.030 0.0301055 0.50 to 0.60 0.60 to 0.90 0.030 0.0301060 0.55 to 0.65 0.60 to 0.90 0.030 0.0301064 0.60 to 0.70 0.50 to 0.80 0.030 0.0

18、301065 0.60 to 0.70 0.60 to 0.90 0.030 0.0301070 0.65 to 0.75 0.60 to 0.90 0.030 0.0301074 0.70 to 0.80 0.50 to 0.80 0.030 0.0301078 0.72 to 0.85 0.30 to 0.60 0.030 0.0301080 0.75 to 0.88 0.60 to 0.90 0.030 0.0301084 0.80 to 0.93 0.60 to 0.90 0.030 0.0301085 0.80 to 0.93 0.70 to 1.00 0.030 0.0301086

19、 0.80 to 0.93 0.30 to 0.50 0.030 0.030109010950.85 to 0.980.90 to 1.030.60 to 0.900.30 to 0.500.0300.0300.0300.0301524 0.19 to 0.25 1.35 to 1.65 0.030 0.0301527 0.22 to 0.29 1.20 to 1.50 0.030 0.0301536 0.30 to 0.37 1.20 to 1.50 0.030 0.0301541 0.36 to 0.44 1.35 to 1.65 0.030 0.0301548 0.44 to 0.52

20、1.10 to 1.40 0.030 0.0301552 0.47 to 0.55 1.20 to 1.50 0.030 0.030AGrades with a specified maximum carbon content of 0.40 % or higher on heat analysis shall have a silicon content from 0.15 to 0.40 % on heat analysis, unless otherwisespecified on the order.A830/A830M 142SUPPLEMENTARY REQUIREMENTSSup

21、plementary requirements shall not apply unless specified in the purchase order or contract.Standardized supplementary requirements for use at the option of the purchaser are listed inSpecification A6/A6M. Those that are considered suitable for use with this specification are listed bytitle:S1. Vacuu

22、m Treatment,S2. Product Analysis, andS8. Ultrasonic Examination.ADDITIONAL SUPPLEMENTARY REQUIREMENTSIn addition, the following special supplementary requirements are also suitable for use with thisspecification.S96. Silicon RequirementS96.1 When a silicon content, or limitation, of other thanfrom 0

23、.15 to 0.40 % on heat analysis is required, the specificrequirements shall be as specified on the order.TABLE 2 Heat Analysis Ranges for Carbon Steel PlatesNOTE 1CarbonWhen the maximum manganese limit exceeds 1.00 %, add 0.01 to the carbon range shown in Column 3.NOTE 2BoronBoron steels can be expec

24、ted to have 0.0005 % minimum boron content.NOTE 3LeadCarbon steels can be produced with a lead range from 0.15 to 0.35. A heat analysis for lead is not determinable, since lead is addedto the stream while each ingot is poured.ElementChemical Ranges, %When Maximum of Specified Element isRangeCarbon T

25、o 0.15, incl 0.05Over 0.15 to 0.30, incl 0.06Over 0.30 to 0.40, incl 0.07Over 0.40 to 0.60, incl 0.08Over 0.60 to 0.80, incl 0.11Over 0.80 0.14Manganese To 0.50, inclOver 0.50 to 1.15, inclOver 1.15 to 1.65, incl0.200.300.35Phosphorus To 0.08, incl 0.03Sulfur To 0.08, incl 0.03Over 0.08 to 0.15, inc

26、l 0.05Over 0.15 to 0.23, incl 0.07Over 0.23 to 0.33, incl 0.10Silicon To 0.15, inclOver 0.15 to 0.30, inclOver 0.30 to 0.60, incl0.080.150.30Copper When copper is required, 0.20 % minimum is commonly specified.A830/A830M 143SUMMARY OF CHANGESCommittee A01 has identified the location of selected chan

27、ges to this standard since the last issue(A830/A830M 13) that may impact the use of this standard. (Approved May 1, 2014.)(1) Modified phosphorus and sulfur levels of Table 1.Committee A01 has identified the location of selected changes to this standard since the last issue(A830/A830M 11) that may i

28、mpact the use of this standard. (Approved May 1, 2013.)(1) Revised Section 4 to require all steels to be killed.(2) Removed Supplementary Requirement S97 limiting the useof Rimmed or Capped Steels.ASTM International takes no position respecting the validity of any patent rights asserted in connectio

29、n with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible

30、technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consid

31、eration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Bar

32、r Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).A830/A830M 144