ASTM A479 A479M-2011 Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels《锅炉和其他压力容器用不锈钢棒材和型材标准规格》.pdf

《ASTM A479 A479M-2011 Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels《锅炉和其他压力容器用不锈钢棒材和型材标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM A479 A479M-2011 Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels《锅炉和其他压力容器用不锈钢棒材和型材标准规格》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A479/A479M 11Used in USDOE-NE StandardsStandard Specification forStainless Steel Bars and Shapes for Use in Boilers andOther Pressure Vessels1This standard is issued under the fixed designation A479/A479M; the number immediately following the designation indicates the yearof original ad

2、option or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1

3、. Scope*1.1 This specification2covers hot- and cold-finished bars ofstainless steel, including rounds, squares, and hexagons, andhot-rolled or extruded shapes such as angles, tees, and channelsfor use in boiler and pressure vessel construction.2NOTE 1There are standards covering high nickel, chromiu

4、m, auste-nitic corrosion, and heat-resisting alloy materials. These standards areunder the jurisdiction of ASTM Subcommittee B02.07 and may be foundin Annual Book of ASTM Standards, Vol 02.04.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The v

5、alues stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 Unless the order specifies the applicable “M” specifica-tion designation, the material shal

6、l be furnished to the inch-pound units.2. Referenced Documents2.1 ASTM Standards:3A262 Practices for Detecting Susceptibility to IntergranularAttack in Austenitic Stainless SteelsA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA484/A484M Specification for General Requirement

7、s forStainless Steel Bars, Billets, and ForgingsA751 Test Methods, Practices, and Terminology for Chemi-cal Analysis of Steel ProductsE112 Test Methods for Determining Average Grain SizeE527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)2.2 SAE Document:4SAE J 1086 Rec

8、ommended Practice for Numbering Metalsand Alloys3. General Requirements3.1 The following requirements for orders for materialfurnished under this specification shall conform to the appli-cable requirements of the current edition of SpecificationA484/A484M.3.1.1 Definitions,3.1.2 General requirements

9、 for delivery,3.1.3 Ordering information,3.1.4 Process,3.1.5 Special tests,3.1.6 Heat treatment,3.1.7 Dimensions and permissible variations,3.1.8 Workmanship, finish, and appearance,3.1.9 Number of tests/test methods,3.1.10 Specimen preparation,3.1.11 Retreatment,3.1.12 Inspection,3.1.13 Rejection a

10、nd rehearing,3.1.14 Material test report,3.1.15 Certification, and3.1.16 Packaging, marking, and loading.4. Other Requirements4.1 In addition to the requirements of this specification, allrequirements of the current editions of Specification A484/A484M shall apply. Failure to comply with the general

11、requirements of Specification A484/A484M constitutes non-conformance with this specification.5. Chemical Composition5.1 Chemical composition shall be reported to the pur-chaser, or his representative, and shall conform to the require-ments specified in Table 1.1This specification is under the jurisd

12、iction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.17 on Flat-Rolled and Wrought Stainless Steel.Current edition approved May 1, 2011. Published June 2011. Originallyapproved in 1962. Last previous edition approved in 2010 as

13、A479/A479M 10a.DOI: 10.1520/A0479_A0479M-11.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SA-479/SA-479M in Section II of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual

14、 Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Available from Society of Automotive Engineers (SAE), 400 CommonwealthDr., Warrendale, PA 15096-0001, http:/www.sae.org.1*A Summary of Changes section appears at the end of this standard.Copyr

15、ight ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.TABLE 1 Chemical RequirementsUNSDesigna-tionATypeComposition, %BCarbonMan-ganesePhos-phorusSulfur Silicon Chromium Nickel NitrogenMolyb-denumOther ElementsCAustenitic GradesN08020 Alloy 20 0.

16、07 2.00 0.045 0.035 1.00 19.021.0 32.038.0 . . . 2.003.00 Cu 3.04.0Cb 8XC1.00N08367 . . . 0.030 2.00 0.040 0.030 1.00 20.022.0 23.525.5 0.180.25 6.07.0 Cu 0.75N08904 904L 0.020 2.00 0.045 0.035 1.00 19.023.0 23.028.0 0.10 4.05.0 Cu 1.02.0S20161 . . . 0.15 4.06.0 0.045 0.030 3.04.0 15.018.0 4.06.0 0.

17、080.20 . . . . . .S20910 XM-19 0.06 4.06.0 0.045 0.030 1.00 20.523.5 11.513.5 0.200.40 1.503.00 Cb 0.100.30;V 0.100.30S21600 XM-17 0.08 7.59.0 0.045 0.030 1.00 17.520.5 5.07.0 0.250.50 2.003.00 . . .S21603 XM-18 0.03 7.59.0 0.045 0.030 1.00 17.520.5 5.07.0 0.250.50 2.003.00 . . .S21800S21904.XM-110.

18、100.047.09.08.010.00.0600.0450.0300.0303.54.51.0016.018.019.021.58.09.05.57.50.080.180.150.40. .S24000 XM-29 0.08 11.514.5 0.060 0.030 1.00 17.019.0 2.33.7 0.200.40 . . . . . .S30200 302 0.15 2.00 0.045 0.030 1.00 17.019.0 8.010.0 0.10 . . . . . .S30400 304 0.08D2.00 0.045 0.030 1.00 18.020.0 8.010.

19、5 . . . . . . . . .S30403 304L 0.030 2.00 0.045 0.030 1.00 18.020.0 8.012.0 . . . . . . . . .S30409 304H 0.040.10 2.00 0.045 0.030 1.00 18.020.0 8.010.5 . . . . . . . . .S30451 304N 0.08 2.00 0.045 0.030 1.00 18.020.0 8.012.0 0.100.16 . . . . . .S30453 304LN 0.030 2.00 0.045 0.030 1.00 18.020.0 8.01

20、1.0 0.100.16 . . . . . .S30600 . . . 0.018 2.00 0.020 0.020 3.74.3 17.018.5 14.015.5 . . . 0.20 Cu 0.50S30815 . . . 0.050.10 0.80 0.040 0.030 1.402.00 20.022.0 10.012.0 0.140.20 . . . Ce 0.030.08S30908 309S 0.08 2.00 0.045 0.030 1.00 22.024.0 12.015.0 . . . . . . . . .S30909 309H 0.040.10 2.00 0.045

21、 0.030 1.00 22.024.0 12.015.0 . . . . . . . . .S30940 309Cb 0.08 2.00 0.045 0.030 1.00 22.024.0 12.016.0 . . . . . . Cb 103C- 1.10S30880 ER308E0.08 1.002.50 0.030 0.030 0.250.60 19.522.0 9.011.0 . . . . . . . . .S31008 310S 0.08 2.00 0.045 0.030 1.00 24.026.0 19.022.0 . . . . . . . . .S31009 310H 0.

22、040.10 2.00 0.045 0.030 1.00 24.026.0 19.022.0 . . . . . . . . .S31040 310Cb 0.08 2.00 0.045 0.030 1.00 24.026.0 19.022.0 . . . . . . Cb 103C-1.10S31254 . . . 0.020 1.00 0.030 0.010 0.80 19.520.5 17.518.5 0.180.22 6.06.5 Cu 0.501.00S31600 316 0.08C2.00 0.045 0.030 1.00 16.018.0 10.014.0 . . . 2.003.

23、00 . . .S31603 316L 0.030 2.00 0.045 0.030 1.00 16.018.0 10.014.0 . . . 2.003.00 . . .S31609 316H 0.040.10 2.00 0.045 0.030 1.00 16.018.0 10.014.0 . . . 2.003.00 . . .S31635 316Ti 0.08 2.00 0.045 0.030 1.00 16.018.0 10.014.0 0.10 2.003.00 Ti 53(C+N)- 0.70S31640 316Cb 0.08 2.00 0.045 0.030 1.00 16.01

24、8.0 10.014.0 0.10 2.003.00 Cb 103C- 1.10S31651 316N 0.08 2.00 0.045 0.030 1.00 16.018.0 10.014.0 0.100.16 2.003.00 . . .S31653 316LN 0.030 2.00 0.045 0.030 1.00 16.018.0 10.014.0 0.100.16 2.003.00 . . .S31700 317 0.08 2.00 0.045 0.030 1.00 18.020.0 11.015.0 . . . 3.04.0 . . .S31725 . . . 0.030 2.00

25、0.045 0.030 1.00 18.020.0 13.517.5 0.20 4.05.0 . . .S31726 . . . 0.030 2.00 0.045 0.030 1.00 17.020.0 14.517.5 0.100.20 4.05.0 . . .S31727 . . . 0.030 1.00 0.030 0.030 1.00 17.519.0 14.516.5 0.150.21 3.84.5 Cu 2.84.0S32050 . . . 0.030 1.50 0.035 0.020 1.00 22.024.0 20.023.0 0.210.32 6.06.8 Cu 0.40S3

26、2053 . . . 0.030 1.00 0.030 0.010 1.00 22.024.0 24.026.0 0.170.22 5.06.0 . . .S32100 321 0.08D2.00 0.045 0.030 1.00 17.019.0 9.012.0 . . . . . . Ti 53(C+N)- 0.70FS32109 321H 0.040.10 2.00 0.045 0.030 1.00 17.019.0 9.012.0 . . . . . . Ti 43(C+N)- 0.70FS32615 . . . 0.07 2.00 0.045 0.030 4.86.0 16.519.

27、5 19.022.0 . . . 0.301.50 Cu 1.502.50S32654 . . . 0.020 2.04.0 0.030 0.005 0.50 24.025.0 21.023.0 0.450.55 7.08.0 Cu 0.300.60S33228 . . . 0.040.08 1.00 0.020 0.015 0.30 26.028.0 31.033.0 . . . . . . Cb 0.601.00;Ce 0.050.10;Al 0.025S34565 . . . 0.030 5.07.0 0.030 0.010 1.00 23.025.0 16.018.0 0.400.60

28、 4.05.0 Cb 0.10S34700 347 0.08D2.00 0.045 0.030 1.00 17.019.0 9.012.0 . . . . . . Cb 103C1.10S34709 347H 0.040.10 2.00 0.045 0.030 1.00 17.019.0 9.012.0 . . . . . . Cb 83C1.10S34800 348 0.08D2.00 0.045 0.030 1.00 17.019.0 9.012.0 . . . . . . (Cb+Ta) 103C1.10;Ta 0.10;Co 0.20S34809 348H 0.040.10 2.00

29、0.045 0.030 1.00 17.019.0 9.012.0 . . . . . . (Cb + Ta) 83C1.10;Co 0.20;Ta 0.10S35315 . . . 0.040.08 2.00 0.040 0.030 1.202.00 24.026.0 34.036.0 0.120.18 . . . Ce 0.030.08S38815 . . . 0.030 2.00 0.040 0.020 5.506.50 13.015.0 15.017.0 . . . 0.751.50 Al 0.30;Cu 0.751.50Austenitic-Ferritic GradesS31803

30、 . . . 0.030 2.00 0.030 0.020 1.00 21.023.0 4.56.5 0.080.20 2.53.5 . . .S32101 . . . 0.040 4.06.0 0.040 0.030 1.00 21.022.0 1.351.70 0.200.25 0.100.80 Cu 0.100.80S32202 . . . 0.030 2.00 0.040 0.010 1.00 21.524.0 1.002.80 0.180.26 0.45 . . .S32205 . . . 0.030 2.00 0.030 0.020 1.00 22.023.0 4.56.5 0.1

31、40.20 3.03.5 . . .S32506 . . . 0.030 1.00 0.040 0.015 0.90 24.026.0 5.57.2 0.080.20 3.03.5 W 0.050.30S32550 . . . 0.04 1.50 0.040 0.030 1.00 24.027.0 4.56.5 0.100.25 2.93.9 Cu 1.502.50S32750 . . . 0.030 1.20 0.035 0.020 0.80 24.026.0 6.08.0 0.240.32 3.05.0 Cu 0.50A479/A479M 1125.2 When a product ana

32、lysis is performed or requested bythe purchaser, the tolerance limits as described in SpecificationA484/A484M apply unless Supplementary Requirement S3 isinvoked.5.3 Methods and practices relating to chemical analysisrequired by this specification shall be in accordance with TestMethods, Practices,

33、and Terminology A751.6. Grain Size for Austenitic Grades6.1 All austenitic grades shall be tested for average grainsize by Test Methods E112.6.2 The H grades shall conform to an average grain size asfollows:6.2.1 ASTM No. 6 or coarser for Types 304H, 309H, 310H,and 316H,6.2.2 ASTM No. 7 or coarser f

34、or Types 321H, 347H, and348H.6.3 For S32615, the grain size as determined in accordancewith Test Methods E112, comparison method, Plate 11, shall beNo. 3 or finer.6.4 Supplementary Requirement S1 shall be invoked whennonH grade austenitic stainless steels are ordered for ASMECode applications for se

35、rvice above 1000F 540C.TABLE 1 ContinuedUNSDesigna-tionATypeComposition, %BCarbonMan-ganesePhos-phorusSulfur Silicon Chromium Nickel NitrogenMolyb-denumOther ElementsCS32760G. . . 0.030 1.00 0.030 0.010 1.00 24.026.0 6.08.0 0.200.30 3.04.0 Cu 0.501.00;W 0.501.00S32906 . . . 0.030 0.801.50 0.030 0.03

36、0 0.50 28.030.0 5.87.5 0.300.40 1.502.60 Cu 0.80S32950 . . . 0.03 2.00 0.035 0.010 0.60 26.029.0 3.55.2 0.150.35 1.002.50 . . .S39277 . . . 0.025 0.80 0.025 0.002 0.80 24.026.0 6.58.0 0.230.33 3.04.0 Cu 1.202.00W 0.801.20Ferritic GradesS40500 405 0.08 1.00 0.040 0.030 1.00 11.514.5 0.50 . . . . . .

37、Al 0.100.30S43000 430 0.12 1.00 0.040 0.030 1.00 16.018.0 . . . . . . . . . . . .S43035 439 0.07 1.00 0.040 0.030 1.00 17.019.0 0.50 0.04 . . . Ti 0.20 + 4 3 (C+N)1.10; Al 0.15S44400 444 0.025 1.00 0.040 0.030 1.00 17.519.5 1.00 0.035 1.752.50 (Ti+Cb) 0.20 + 4 3(C+N)-0.80S44627 XM-27 0.010H0.40 0.02

38、0 0.020 0.40 25.027.5 0.50 0.015H0.751.50 Cu 0.20;Cb 0.050.20;(Ni+Cu) 0.50S44700 . . 0.010 0.30 0.025 0.020 0.20 28.030.0 0.15 0.020 3.54.2 (C+N) 0.025;Cu 0.15S44800 . . . 0.010 0.30 0.025 0.020 0.20 28.030.0 2.002.50 0.020 3.54.2 (C+N) 0.025;Cu 0.15Martensitic GradesS40300 403 0.15 1.00 0.040 0.030

39、 0.50 11.513.0 . . . . . . . . . . . .S41000 410 0.15 1.00 0.040 0.030 1.00 11.513.5 . . . . . . . . . . . .S41040 XM-30 0.18 1.00 0.040 0.030 1.00 11.513.5 . . . . . . . . . Cb 0.050.30S41400 414 0.15 1.00 0.040 0.030 1.00 11.513.5 1.252.50 . . . . . . . . .S41425 . . . 0.05 0.501.00 0.020 0.005 0.

40、50 12.015.0 4.07.0 0.060.12 1.502.00 Cu 0.30S41500I0.05 0.501.00 0.030 0.030 0.60 11.514.0 3.55.5 . . . 0.501.00 . . .S43100 431 0.20 1.00 0.040 0.030 1.00 15.017.0 1.252.50 . . . . . . . . .ANew designations established in accordance with Practice E527 and SAE J 1086 published jointly by ASTM and S

41、AE. See ASTM DS56C, available from ASTMHeadquarters.BMaximum unless otherwise indicated.CExcept as required for specific alloy type, molybdenum, titanium, nickel, cobalt, tantalum, nitrogen, and copper need not be reported but shall not be present in otherthan residual amounts, the intent being to p

42、rohibit substitution of one alloy type for another due to absence of control of the above named elements in certain alloys.DSee Supplementary Requirement S1.EAmerican Welding Society designation.FNitrogen content is to be reported for this grade.G%Cr+3.33 %Mo+163 %N$ 40.HProduct analysis tolerance o

43、ver the maximum limit for carbon and nitrogen to be 0.002 %.IWrought version of CA6NM.A479/A479M 1137. Mechanical Properties Requirements7.1 The material shall conform to the mechanical propertyrequirements specified in Table 2 for the grade ordered.At leastone room-temperature test shall be perform

44、ed by the manufac-turer on a sample from at least one bar or shape from each lotof material.7.2 The yield strength shall be determined by the offset(0.2 %) method as prescribed in Test Methods and DefinitionsA370.7.3 Martensitic material supplied in the annealed conditionshall be capable of meeting

45、the hardened and temperedmechanical properties when heat treated.7.4 Hardness measurements, when required, shall be madeat a location midway between the surface and the center of thecross section.7.5 Martensitic grades shall be capable of meeting thehardness requirements after heat treating as speci

46、fied in Table3.8. Corrosion Testing8.1 Austenitic stainless steels solution annealed by thealternative method shall be tested and pass the intergranularcorrosion test requirements described in S2.9. Testing for Intermetallic Compounds9.1 When specified by the purchaser in the purchase order,the manu

47、facturer shall test the austenitic or austenitic-ferritic(duplex) stainless steel material in its final condition inaccordance with supplementary test requirements S6.NOTE 2Many, if not all, duplex stainless steels and some austeniticstainless steels will form intermetallic phases or compounds such

48、assigma, chi, and laves phases when exposed to temperatures below thespecified annealing temperature or cooled slowly from a higher tempera-ture during casting, welding, or annealing. These phases can have anegative effect on mechanical properties and corrosion resistance. Thesephases can typically

49、be removed by correct annealing and coolingpractices. The presence of these phases can be demonstrated by tests,typically involving metallography, impact toughness, or corrosion resis-tance, although the testing requirements may be different for differentalloy grades. Such testing may or may not be r