ASTM A1006 A1006M-2000(2004) Standard Specification for Steel Line Pipe Black Plain End Laser Beam Welded.pdf

《ASTM A1006 A1006M-2000(2004) Standard Specification for Steel Line Pipe Black Plain End Laser Beam Welded.pdf》由会员分享，可在线阅读，更多相关《ASTM A1006 A1006M-2000(2004) Standard Specification for Steel Line Pipe Black Plain End Laser Beam Welded.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A 1006/A 1006M 00 (Reapproved 2004)Standard Specification forSteel Line Pipe, Black, Plain End, Laser Beam Welded1This standard is issued under the fixed designation A 1006/A 1006M; the number immediately following the designation indicates theyear of original adoption or, in the case o

2、f revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers laser beam welded, black,plain end steel pipe for use in the convey

3、ance of fluids underpressure. Pipe in sizes NPS 1 to 26, inclusive, with nominalwall thickness 0.750 in. 19.1 mm or less, as given in Table 1,is included. Pipe having other dimensions, in this size range,may be furnished provided such pipe complies with all otherrequirements of this specification.1.

4、2 It is intended that the pipe be capable of being circum-ferentially welded in the field when welding procedures inaccordance with the requirements of the applicable pipelineconstruction code are used.1.3 The values stated in either inch-pound units or in SIunits are to be regarded separately as st

5、andard. Within the text,the SI units are shown in brackets. The values in each systemare not exact equivalents: therefore, each system is to be usedindependently of the other, without combining values in anyway.1.4 The following precautionary statement pertains to thetest method portion, Section 14,

6、 of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to us

7、e.2. Referenced Documents2.1 ASTM Standards:2A 370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA 450/A 450M Specification for General Requirements forCarbon, Ferritic Alloy, and Austenitic Alloy Steel TubesA 530/A 530M Specification for General Requirements forSpecialized Car

8、bon and Alloy Steel PipeA 751 Test Methods, Practices, and Terminology forChemical Analysis of Steel ProductsA 941 Standard Terminology Relating to Steel, StainlessSteel, Related Alloys, and Ferroalloys1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and R

9、elated Alloys and is the direct responsibility of SubcommitteeA01.09 on Carbon Steel Tubular Products.Current edition approved Sept 1, 2004. Published October 2004. Originallyapproved in 2000. Last previous edition approved in 2000 as A 1006/A 1006M 00.2For referenced ASTM standards, visit the ASTM

10、website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.TABLE 1 Dimensions and Weight Mass Per Unit LengthNOTEPipe having an outside diameter and/or wall thickness

11、interme-diate to those listed in this table are also permitted.NPS Outside Diameter Wall Thickness Weight Mass per UnitLengthDesignator in. mm in. mm lb/ft kg/m1 1.315 33.4 0.133 3.4 1.68 2.520.358 9.1 3.66 4.55114 1.660 42.2 0.140 3.6 2.27 3.430.382 9.7 5.22 7.77112 1.900 48.3 0.145 3.7 2.72 4.070.

12、400 10.2 6.41 9.582 2.375 60.3 0.083 2.1 2.03 3.010.436 11.1 9.04 13.47212 2.875 73.0 0.083 2.1 2.48 3.670.552 14.0 13.71 20.373 3.500 88.9 0.083 2.1 3.03 4.500.600 15.2 18.60 27.63312 4.000 101.6 0.083 2.1 3.48 5.150.318 8.1 12.52 18.684 4.500 114.3 0.083 2.1 3.92 5.810.674 17.1 27.57 40.995 5.563

13、141.3 0.083 2.1 4.86 7.210.750 19.1 38.59 57.566 6.625 168.3 0.083 2.1 5.80 8.610.750 19.1 47.10 70.278 8.625 219.1 0.125 3.2 11.36 17.040.750 19.1 63.14 94.2010 10.750 273.1 0.156 4.0 17.67 26.540.750 19.1 80.18 119.6412 12.750 323.9 0.172 4.4 23.13 34.670.750 19.1 96.21 143.5614 14.000 355.6 0.188

14、 4.8 27.76 41.520.750 19.1 106.23 158.4916 16.000 406.7 0.188 4.8 31.78 47.540.750 19.1 122.27 182.4218 18.000 457 0.188 4.8 35.80 53.530.750 19.1 138.30 206.2520 20.000 508 0.219 5.6 46.31 69.380.750 19.1 154.34 230.2722 22.000 559 0.219 5.6 50.99 76.420.750 19.1 170.37 254.3024 24.000 610 0.250 6.

15、4 63.47 95.260.750 19.1 186.41 278.3226 26.000 660 0.250 6.4 68.82 103.150.750 19.1 202.44 301.871Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.2.2 API Publication:API RP 5L3 Recommended Practice for Conducting Drop-Weight Tear Test

16、s on Line Pipe32.3 ASME Standard:ASME Boiler and Pressure Vessel Code, Section IX, Weld-ing and Brazing Qualifications43. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 laser beam welding, na welding process that utilizesa laser beam to produce melting of full thickness of edges

17、 to bewelded, followed by the fusion of those edges.3.1.2 specified outside diameter, nthe outside diametershown in the purchase order or in Table 1 for the applicableNPS size.3.2 DefinitionsFor definitions of other terms used in thisspecification, refer to Terminology A 941.4. Ordering Information4

18、.1 Information items to be considered, if appropriate, forinclusion in the purchase order are as follows:4.1.1 Specification designation and year of issue,4.1.2 Quantity (feet or metres),4.1.3 Grades (see Table 2 or 8.6),4.1.4 Size, either nominal (NPS) or outside diameter andwall thickness,4.1.5 No

19、minal length (see 16.3),4.1.6 End finish (plain end beveled or special, see 17.1),4.1.7 Bar coding (see 20.3),4.1.8 Special requirements, and4.1.9 Supplementary requirements.5. General Requirements5.1 Pipe furnished under this specification shall conform tothe applicable requirements of Specificatio

20、n A 530/A 530Munless otherwise provided herein.6. Materials and Manufacture6.1 Pipe shall be welded from one side by the laser beamwelding process using a single pass with an appropriateshielding gas. The pipe shall have one longitudinal seam. Theweld shall be made in accordance with a qualified wel

21、dingprocedure as specified in ASME Boiler and Pressure VesselCode, Section IX, Paragraph QW-264. The edges may bepreheated.6.2 The internal and external weld protrusion resulting fromthe welding process shall be removed, in accordance with therequirements of 18.1 and 18.2.6.3 The weld seam and its h

22、eat affected zone shall receiveeither a normalizing heat treatment or a continuous in-line heattreatment in such a manner that no untempered martensiteremains. Complete penetration and coverage of the weld andthe weld heat affected zone by this heat treatment shall beconfirmed by periodic metallogra

23、phic examination of weldarea cross-section specimens at least once per working shift.7. Chemical Composition7.1 The steel shall contain no more than 0.22 % carbon,0.015 % sulfur, and 0.025 % phosphorus, by heat and productanalyses.7.2 The steel shall contain no more than 0.0007 % boron, byheat analy

24、sis.7.3 The carbon equivalent (CE) value for each heat shall notexceed 0.40 %, calculated using the product analyses and thefollowing equation:CE 5 C 1 FFMn61Si241Cu151Ni201Cr 1 Mo 1 V 1 Cb5G(1)where:F = a compliance factor that is dependent upon the carboncontent, as shown below:Carbon Content, % F

25、 Carbon Content, % FNPS 12 100 lengths 1TABLE 7 Permissible Variations on LengthsNominal Length Minimum Length Minimum Avg. LengthFor Each Order ItemMaximum Lengthft m ft m ft m ft m20 6 9.0 2.74 17.5 5.33 22.5 6.8640 12 14.0 4.27 35.0 10.67 45.0 13.7250 13 17.5 5.33 43.8 13.35 55.0 16.7660 18 21.0

26、6.40 52.5 16.0 65.0 19.8180 24 28.0 8.53 70.0 21.34 85.0 25.91A 1006/A 1006M 00 (2004)5testing device of appropriate accuracy. In case of a dispute, themeasurement determined by the use of a mechanical calipershall govern.18.5 Repairs of the pipe body, by welding, are not permit-ted.18.6 Repair of t

27、he WeldDefects in welds may be repairedonly by agreement between the purchaser and the manufac-turer; such repairs shall be in accordance with SpecificationA 530/A 530M, except that the repair depth shall not exceed70 % of the specified wall thickness of the pipe and back-to-back repairs are not per

28、mitted. No repair of repair weld ispermitted.18.7 Pipe smaller than NPS 4 shall be reasonably straight.For all other pipe, the measured deviation from a straight lineshall not exceed 0.2 % of the length.18.8 The pipe shall contain no dents greater than 10 % ofthe specified outside diameter or14 in.

29、6.4 mm, whichever issmaller, measured as the gap between the lowest point of thedent and a prolongation of the original contour of the pipe.Cold formed dents deeper than18 in. 3.2 mm shall be free ofsharp-bottom gouges. The gouges may be removed by grind-ing, provided that the remaining wall thickne

30、ss is withinspecified limits. The length of the dent in any direction shallnot exceed one half the pipe diameter.19. Certification19.1 A certified test report shall be furnished.20. Package Marking20.1 Each length of pipe shall be legibly marked by sten-ciling to show: specification number, the name

31、 or brand of themanufacturer, LBW, the grade, wall thickness, diameter, heatnumber, and the length, except as allowed in 20.2. The lengthshall be marked in feet and tenths of a foot, or metres to twodecimal places, as applicable.20.2 For pipe NPS 112 and smaller that is bundled, theinformation in 20

32、.1 may be marked on a tag that is securelyfastened to each bundle.20.3 In addition to the requirements of 20.1 and 20.2, barcoding is acceptable as a supplementary identification method.The purchaser may specify in the order a specific bar codingsystem to be used.21. Keywords21.1 black steel pipe; l

33、aser beam welded; line pipeSUPPLEMENTARY REQUIREMENTSThe following supplementary requirement shall apply only when specified in the purchase order.S1. Drop-Weight Tear TestingS1.1 The drop-weight tear test shall be conducted in accor-dance with API RP 5L3.S1.2 The temperature selected for conducting

34、 the drop-weight tear test, the test frequency, and the criteria foracceptance shall be as specified in the purchase order.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expr

35、essly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revise

36、d, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may

37、attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United State

38、s. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 8 Depth of Groove ToleranceSpecified Wall Thickness (t),in. mmMaximum Depth of Groove,in. mm0.150 3.8 or less 0.10t0.150 3.8 to 0.300 7.50.015 0.40.300 7.5 or greater 0.05tA 1006/A 1006M 00 (2004)6