ASTM A100-2007(2012) Standard Specification for Ferrosilicon 《硅铁合金的标准规格》.pdf

《ASTM A100-2007(2012) Standard Specification for Ferrosilicon 《硅铁合金的标准规格》.pdf》由会员分享，可在线阅读，更多相关《ASTM A100-2007(2012) Standard Specification for Ferrosilicon 《硅铁合金的标准规格》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: A100 07 (Reapproved 2012)Standard Specification forFerrosilicon1This standard is issued under the fixed designation A100; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parenthes

2、es indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers grades of ferrosilicon forsteelmaking and foundry uses.1.2 The values stated in inch-pound units are to be regardedas the stand

3、ard. The metric equivalents of inch-pound units (SIunits) given in parentheses may be approximate.2. Referenced Documents2.1 ASTM Standards:2A1025 Specification for Ferroalloys and Other AlloyingMaterials, General RequirementsE11 Specification for Woven Wire Test Sieve Cloth and TestSievesE360 Test

4、Methods for Chemical Analysis of Silicon andFerrosilicon33. General Conditions of Delivery3.1 Materials furnished to this specification shall conform tothe requirements of SpecificationA1025, including any supple-mentary requirements that are indicated in the purchase order.Failure to comply with th

5、e general requirements of Specifica-tion A1025 constitutes nonconformance with this specification.In case of conflict between the requirements of this specifica-tion and Specification A1025, this specification shall prevail.4. Chemical Composition4.1 The various grades shall conform to the requireme

6、nts asto chemical composition prescribed in Table 1.4.2 The manufacturer shall furnish an analysis of eachshipment showing the silicon content and when required, suchof the other elements specified in Table 1.5. Size5.1 The various grades are available in sizes as listed inTable 2.5.2 The sizes list

7、ed in Table 2 are typical as shipped fromthe manufacturers plant. These alloys exhibit varying degreesof friability; therefore, some attrition may be expected intransit, storage, and handling. A quantitative test is not avail-able for rating relative friability of ferroalloys. A code systemhas been

8、developed, therefore, for this purpose, and a numberrating for each product type is shown in the last column ofTable 2. Definitions applicable to these code numbers are givenin Specification A1025.6. Chemical Analysis6.1 Unless otherwise agreed upon, the chemical analysis ofthe material shall be mad

9、e in accordance with Test MethodsE360.6.2 If alternative methods of analysis are used, MethodsE360 shall be used for referee.6.3 Where a method is not given in Methods E360 for theanalysis for a particular element, the analysis shall be made inaccordance with a procedure agreed upon between the manu

10、-facturer and the purchaser.7. Keywords7.1 ferroalloy; ferrosilicon1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.18 on Castings.Current edition approved March 1, 2012. Published Apri

11、l 2012. Originallyapproved in 1925. Last previous edition approved in 2007 as A100 07. DOI:10.1520/A0100-12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the stan

12、dards Document Summary page onthe ASTM website.3Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 194

13、28-2959, United States.TABLE 1 Chemical RequirementsElement GradeC CA CB C1 C2 D DA E EA E1 F F1 F1A G GA G1 G1AComposition, %A,BSilicon 74.079.074.079.074.079.074.079.074.079.065.070.065.070.047.051.047.051.047.051.020.024.020.024.020.024.014.017.014.017.014.017.014.017.0Carbon 0.10 0.10 0.10 0.10

14、0.10 0.10 0.10 .010 .010 0.10 0.50 0.50 0.50 0.70 0.70 0.70 0.70Sulfur 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025 0.025Phosphorous 0.035 0.035 0.035 0.035 0.035 0.035 0.035 0.040 0.040 0.040 0.120 0.120 0.120 0.120 0.120 0.120 0.120Aluminum 1.50 0

15、.50 0.10 1.001.501.001.501.25 0.10 1.25 0.40 1.25 1.00 1.00 1.00 0.75 0.75 0.75 0.75Manganese 0.40 0.40 0.40 0.40 0.40 0.50 0.50 0.75 0.75 0.75 1.00 1.00 1.00 1.25 1.25 CalciumC0.51.50Born 0.40.10 0.040.100.040.10 0.040.100.040.10AA single value indicates a maximum, except for calcium.BWhen shipped

16、in 3000 lb containers, the average boron content of a container shall not vary from the average reported for the entire shipment by more than 0.010 %.CMinimum.A10007(2012)2SUPPLEMENTARY REQUIREMENTSThe composition shall be further limited to the requirements of Table S1.1. Upon request of thepurchas

17、er, the manufacturer shall furnish an analysis of these elements on a schedule agreed betweenthe manufacturer and purchaser.TABLE 2 Standard Sizes and TolerancesGrades Standard SizesTolerances and Sieve Sizes Defined byASTM Specification E11FriabilityRatingAC,D,E 8-in. (203-mm) by 4-in.(102-mm)90-lb

18、 (40.8-kg) lump, max 10 %, max, passing 4-in. (102-mm)sieve8-in. (203-mm) by 2-in.(50.8-mm)90-lb (40.8-kg) lump, max 10 %, max, passing 2-in. (50.8-mm)sieve5-in. (127-mm) by 2-in.(50.8-mm)10 %, max, retained on 5-in. (127-mm)sieve10 %, max, passing 2-in. (50.8-mm)sieve4-in. (102-mm) by12-in.(12.7-mm

19、)10 %, max, retained on 4-in. (102-mm)sieve10 %, max, passing12-in. (12.7-mm)sieve4-in. (102-mm) by down 10 %, max, retained on 4-in. (102-mm)sieve12 %, max, passing14-in. (6.35-mm)sieve3-in. (76.2-mm) by12-in.(12.7-mm)10 %, max, retained on 3-in. (76.2-mm)sieve15 %, max, passing12-in. (12.7-mm)siev

20、e3-in. (76.2-mm) by down 10 %, max, retained on 3-in. (76.2-mm)sieve15 %, max, passing No. 8 (2.38-mm)sieve2-in. (50.8-mm) by12 in. (12.7-mm) 10 %, max, retained on 2-in. (50.8-mm)sieve15 %, max, passing12-in. (12.7-mm)sieve2-in. (50.8-mm) by down 10 %, max, retained on 2-in. (50.8-mm)sieve15 %, max

21、, passing No. 8 (2.38-mm)sieve1-in. (25.4-mm) by No. 8(2.38-mm)5 %, max, retained on 1-in. (25.4-mm)sieve10 %, max, passing No. 8 (2.38-mm)sieve1-in. (25.4-mm) by down 5 %, max, retained on 1-in. (25.4-mm)sieve20 %, max, passing No. 8 (2.38-mm)sieveC,D,F Lump or Pig 90-lb (40.8-kg) lump or pig, maxC

22、,D,E12-in. (12.7-mm) by No. 8 (2.38-mm) 5 %, max, retained on12-in. (12.7-mm)sieve10 %, max, passing No. 8 (2.38-mm)sieve38-in. (9.51-mm) by No. 6(3.36-mm)5 %, max, retained on38-in. (9.51-mm)sieve10 %, max, passing No. 6 (3.36-mm)sieve38-in. (9.51-mm) by No. 12 (1.68-mm) 5 %, max, retained on38-in.

23、 (9.51-mm)sieve10 %, max, passing No. 14 (1.41-mm)sieve38-in. (9.51-mm) by down 5 %, max, retained on38-in. (9.51-mm)sieve15 %, max, passing No. 70 (0.21-mm)sieve14-in. (6.35-mm) by down 5 %, max, retained on14-in. (6.35-mm)sieveNo. 8 (2.38-mm) by down 5 %, max, retained on No. 8 (2.38-mm)sieveNo. 2

24、8 (841-m) by down 5 %, max, retained on No. 20 (841-m)sieveG pig 90-lb (40.8-kg) pig, max.ASee Appendixes.A100 07 (2012)3TABLE S1.1 Supplementary Chemical RequirementsElement GradeC CA CB C1 C2 D DA E EA E1 E1A F F1 F1A G GA G1 G1AComposition, % maximumChromium 0.30 0.30 0.30 0.50 0.50 0.50 0.50 0.1

25、5 0.15 0.25 0.25 0.25 0.25 0.25 Nickel 0.10 0.10 0.10 0.20 0.20 0.30 0.30 Copper 0.10 0.10 0.10 0.20 0.20 0.30 0.30 Titanium 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20A10007(2012)4APPENDIX(Nonmandatory Information)X1. FRIABILITY RATINGSX1.1 Proposed friability ratings are

26、shown in Table X1.1 asfollows:TABLE X1.1 Proposed Friability Ratings for FerrosiliconProductGradeProposedFriabilityRatingC4D4E5F4G2A100 07 (2012)5SUMMARY OF CHANGESCommittee A01 has identified the location of selected changes to this standard since the last issue (A100 04)that may impact the use of

27、this standard.(1) Revised Table 1 and footnotes to Table 1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such pat

28、ent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited eit

29、her for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair

30、hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this stand

31、ard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).A100 07 (2012)6