ASME B16 23-2002 Cast Copper Alloy Solder Joint Drainage Fittings DWV《DWV类铸铜合金钎焊连接排水管件》.pdf

《ASME B16 23-2002 Cast Copper Alloy Solder Joint Drainage Fittings DWV《DWV类铸铜合金钎焊连接排水管件》.pdf》由会员分享，可在线阅读，更多相关《ASME B16 23-2002 Cast Copper Alloy Solder Joint Drainage Fittings DWV《DWV类铸铜合金钎焊连接排水管件》.pdf（91页珍藏版）》请在麦多课文档分享上搜索。

1、Errata to ASME BI 6.23-2002 Cast Copper Alloy Solder Joint Drainage Fittings: DWV On page Viii, Committee Roster revised. Revisions appear on the overleaf. THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS Three Park Avenue, New York, NY 10016-5990 March 2003 J1402E Copyright ASME International Provided

2、by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-ASME BI6 COMMITTEE Standardization of Valves, Flanges, Fittings, Gaskets, and Valve Actuators (The following is the roster of the Committee at the time of approval of this Standard.) OFFICE

3、RS W. N. McLean, Chair H. R. Sonderegger, Vice Chair P. A. Reddington, Secretary COMMITTEE PERSONNEL R. W. Barnes, Anric Enterprises R. R. Brodin, Fisher Controls International, Inc. T. A. McMahon, Alternate, Fisher Controls International, Inc. M. A. Clark, Nibco, Inc. A. Cohen, Arthur Cohen and Ass

4、ociates C. E. Floren, Mueller Co. D. R. Frikken, Solutia, Inc. G. A. Jolly, Vogt Valve Co. W. G. Knecht, Retired R. Koester, The William Powell Co. W. N. McLean, Newco Valves M. L. Nayyar, Bechtel Power Corp. P. A. Reddington, The American Society of Mechanical Engineers R. A. Schmidt, Trinity-Ladis

5、h Co. H. R. Sonderegger, Anvil International, Inc. W. M. Stephan, Flexitallic, Inc. T. F. Stroud, Ductile Iron Pipe Research Association R. E. White, Richard E. White and Associates D. A. Williams, Southern Company Services L. A. Willis, The Dow Chemical Co. - W. R. Worley, Consultant SUBCOMMITTEE J

6、 - COPPER AND COPPER ALLOY FLANGES, FLANGED FITTINGS, AND SOLDER JOINT FITTINGS M. A. Clark, Chair, Nibco, Inc. A. G. Kireta, Jr., Vice Chair, Copper Development Association. Inc. G. E. Moino, Secretary, The American Society of Mechanical D. F. Buccicone, Elkhart Products Corp. A. Cohen, Arthur Cohe

7、n and Associates D. R. Frikken, Solutia, Inc. A. A. Knapp, Canadian Copper/Brass Development Association L. MeDaniel, Mueller Copper Fittings, LP T. L. Jarnison, Alternate, Mueller Industries Engineers . v111 Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reprod

8、uction or networking permitted without license from IHS-,-Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-The American Society of Mechanical Engineers AN AMERICAN NATIONAL STANDARD GAST GOPPER ALLOY

9、SOLDER JOINT DRAM AGE FITTINCS: DWV ASME B16.23-2002 (Revision of ASME B16.23-1812) Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-Date of Issuance: November 8,2002 The next edition of this Standard

10、 is scheduled for publication in 2007. There will be no addenda issued to this edition. ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard. Interpretations are published on the ASME Web site under the Committee Pages at http:ll.asrne.org/codesl

11、as they are issued. ASME is the registered trademark of The American Society of Mechanical Engineers. This code or standard was developed under procedures accredited as meeting the criteria for American National Standards. The Standards committee that approved the code or standard was balanced to as

12、sure that individuals from competent and concerned interests have had an opportunity to participate. The proposed code or standard was made available for public review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at

13、-large. ASME does not “approve,“ “rate,“ or “endorse“ any item, construction, proprietary device, or activity. ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone u

14、tilizing a standard against liability for infringement of any applicable letters patent, nor assume any such liability. Users of a code or standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own r

15、esponsibility. Participation by federal agency representative(s.1 or person(s) affiliated with industry is not to be interpreted as government or industry endorsement of this code or standard. ASME accepts responsibility for only those interpretations of this document issued in accordance with the e

16、stablished ASME procedures and policies, which precludes the issuance of interpretations by individuals. No part of this document may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. The American Society of Mechanical E

17、ngineers Three Park Avenue, New York, NY 10016-5990 Copyright O 2002 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A. Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IH

18、S-,-CONTENTS Foreword Standards Committee Roster . Correspondence With the B16 Committee . 1 Scope . 2 Description . 3 Pitch (Slope) 4 Abbreviations . 5 Size 6 Marking . 7 Material 8 Metal Thickness 9 Inspection Tolerance 10 Threaded Ends., 11 Configuration of Threaded Ends . Figures 2 Typical Layin

19、g Lengths of DWV 90 deg Elbows Tables 1 Inspection Tolerance Table 2 Dimensions of Solder Joint Ends . DWV 3 Dimensions of Threaded Ends - DWV . 4 Flush Bushings . 5 Dimensions of DWV Adapters 6 Dimensions of DWV Short Adapters 7 Dimensions of DWV Trap Adapters . Heavy Soil Pipe . 10 Dimensions of C

20、 X No-Hub Soil Pipe Adapter Dimensions of C X Hub Soil Pipe Adapter 1 Size Sequence of Fittings . Dimensions for DWV Couplings, Reducers. Extended Bushings. and 8 9 Dimensions of C to Soil Pipe Adapter for Joining to Extra Heavy Soil Pipe Dimensions of C to Soil Pipe Adapter - Plain End for Joining

21、to Extra 11 vi . VI11 ix 1 2 2 2 2 2 2 2 2 3 3 1 3 3 4 5 10 11 12 iii Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38

22、39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Dimensions of DWV 45 deg Y With Cleanout . Soil Pipe (Spigot) x C X Cleanout . Dimensions of DWV Elbows and Double Elbows . C X C . Dimensions of Reducing DWV Single and Double Elbows C X C Dimensions of DWV Elbows Dimensions of DWV Reducing Elbows

23、Dimensions of DWV Elbows Dimensions of DWV Tees and Double Tees Dimensions of DWV Tees and Double Tees Dimensions of DWV Trap Tees Dimensions of DWV Double and Quaruple Branch Fittings Inlet), Single and Double . Inlet). Single and Double . Inlet). Single and Double . Inlet). Single and Double . Dim

24、ensions of Single and Double DWV 45 deg Ys Dimensions of DWV 45 deg Ys Dimensions for DWV Horizontal Twin Branch Tees Dimensions for DWV Fitting Tees. Single and Double Dimensions for DWV Utility Tees . . . Dimensions of Short Design DWV Tees With Side Inlet(s) (90 deg to Main Dimensions of Short De

25、sign DWV Tees With Side Inlet(s) (45 deg to Main Dimensions of Long Design DWV Tees With Side Inlet(s) (90 deg to Main Dimensions of Long Design DWV Tees With Side Inlet(s) (45 deg to Main . Dimensions of DWV Fitting Tees With Side Inlet Maximum Below Center Line Dimensions of DWV Long Turn T.Ys. Si

26、ngle and Double . Dimensions of DWV Double Short T-Y Dimensions of DWV Double Short T-Y Dimensions of DWV Elbow With Inlets Dimensions of DWV Double Branch Sink Fittings . Dimensions of DWV Closet Offset Fittings Dimensions of DWV 90 deg Closet Elbow . . . Dimensions of Floor Flange Vent Support . D

27、imensions of DWV Closet Ells With Side Inlet(s) (90 deg and 45 deg) to Main Iniet(s) Dimensions of DWV Closet Ells With or Without Side Inlet(s) (90 deg and 45 deg) to Main Inlet(s) Dimensions of DWV Closet Flanges . Dimensions of Vent Tees and Vent Double Tees . Dimensions of Vent Elbows . Dimensio

28、ns of DWV Stack Upturns. Single and Double Dimensions of Slip Joint Pieces . Dimensions of Trap Coupling . Dimensions of Slip Joint Ends Dimensions of DWV Cap . Dimensions of DWV Plugs . Dimensions of DWV Drum Traps . Dimensions of DWV Swivel Drum Trap . Dimensions of DWV Traps . Dimensions of DWV T

29、est Tees With Plug . Dimensions of Trap Extended Bushings 12 13 14 15 16 16 17 18 19 19 19 20 20 21 22 23 23 23 24 24 25 26 26 26 27 27 28 28 29 30 31 32 32 32 33 33 33 34 34 34 35 36 37 38 iv Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networ

30、king permitted without license from IHS-,-56 Dimensions of DWV Plugs . 38 I U.S. Customary Tables . 39 A Quality System Programs . 77 Mandatory Appendices . II References 76 Nonmandatory Appendix V Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or n

31、etworking permitted without license from IHS-,-FOREWORD Standardization work on solder joint fittings began in 1936 in Subcommittee 11 of Sectional Committee A40, Minimum Requirements for Plumbing and Standardization of Plumbing Equipment, organized within the American Standards Association (ASA). I

32、t resulted in the publication, in January 1941 of ASA A40.3-1941. That standard covered only supply (pressure) fittings. In 1949, responsibility for solder joint fittings was transferred to newly formed Subcommittee 9 of Sectional Committee B16 on Standardization of Pipe Flanges and Fittings. The ne

33、xt revision of A40.3 appeared as ASA B 16.18-1950, Cast-Brass Solder-Joint Fittings. During its development, however, the need for separate standards for wrought copper and wrought bronze supply fittings and for solder joint drainage fittings was recognized. Work on the wrought fitting standard was

34、undertaken by a joint committee of the Copper and Brass Research Association and the Manufacturers? Standardization Society of the Valve and Fittings Industry (MSS). That work, properly reviewed and approved, was published as ASA B16.22-1951. Concurrently, in June 1949, at the request of Subcommitte

35、e 9, a task group organized by MSS began work on a standard for cast brass solder joint drainage fittings. Representatives of all U.S. and Canadian manufacturers were invited to participate. The Report of the Coordinating Committee for a National Plumbing Code was taken into account; special researc

36、h on wall thickness and depth of solder joint was conducted; coordination with other standards was sought, to avoid inconsistency. After working through nine drafts to reach consensus, the group submitted an April 1952 draft to Subcommittee 9. After committee, sponsor, and ASA approval, the standard

37、 was approved as ASA B16.23-1953, Cast Brass Solder Joint Drainage Fittings, on January 30, 1953. Work soon began on a revision, to include additional sizes, reducing sizes, and additional types of fittings. A March 1955 draft was approved by B16, sponsors, and ASA, and published as ASA B16.23-1955.

38、 Starting in 1958, responding to requests for further revision and expansion, the MSS task group developed a 1959 draft which was approved by Subcommittee 9, the B16 Committee, sponsors, and ASA, and was published as ASA In 1967 and 1968 a complete revision was undertaken, including engineering stud

39、ies to verify that a user request for shorter soldering cups was justified. The resulting draft, after approval by Subcommittee 9, USA Standards Committee B16, sponsors, and the (then called) USA Standards Institute, was published as USAS B16.23-1969. An addenda, dated 1973, lengthened the cups on t

40、he three smallest sizes to overcome assembly problems. The subcommittee, now Subcommittee I, began a new revision in 1974, resulting in the inclusion of the 1973 addenda, addition of metric equivalents, and change of ?bronze? to ?copper alloy.? The draft finally approved by the (again renamed) Ameri

41、can National Standards Institute (ANSI) was published as ANSI B16.23-1976. In 1982, a new edition updating dimensional tables and metric equivalents, was developed. Following approval at ali levels, the revision was published as ANSI B16.23-1984. Also in 1982, American National Standards Committee B

42、I6 became the ASME B16 Standards Committee, operating with the same scope, under ASME procedures accredited B16.23-1960. vi Copyright ASME International Provided by IHS under license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-by ANSI. Subsequently, Subc

43、ommittee I merged with Subcommittee J, which had a related scope. The 1992 edition removed metric units, establishing U.S. Customary units as the standard. Clarifications and updating changes were made in order to improve the text. This 2002 edition of B16.23 adds SI units of measure in the main bod

44、y of text and moves U.S. Customary units to Mandatory Appendix I. A Nonmandatory Appendix for Quality System Problems is added, plus editorial revisions are made to improve the text. Following approvd by the Standards Committee and ASME, approval as an American National Standard was given on Februar

45、y 6, 2002, with the designation ASME B16.23-2002. Requests for interpretations and suggestions for revision should be sent to the Secretary, B16 Committee, The American Society of Mechanical Engineers, Three Park Avenue, New York, NY 10016-5990. vii Copyright ASME International Provided by IHS under

46、 license with ASMENot for ResaleNo reproduction or networking permitted without license from IHS-,-ASME 616 COMMITTEE Standardization of Valves, Flanges, Fittings, Gaskets, and Valve Actuators (The following is the roster of the Committee at the time of approval of this Standard.) OFFICERS W. N. McL

47、ean, Chair R. A. Schmidt, Vice Chair P. A. Reddington, Secretary COMMITTEE PERSONNEL R. W. Barnes, Anric Enterprises R. R. Brodin, Fisher Controls International, Inc. M. A. Clark, Nibco, Inc. A. Cohen, Arthur Cohen and Associates C. E. Floren, Mueller Co. D. R. Frikken, Solutia, Inc. G. A. Jolly, Vo

48、gt Valve Co. W. G. Knecht, BW/IP International, Inc. R. Koester, The William Powell Co. W. N. McLean, Newco Valves M. L. Nayyar, Bechtel Power Corp. P. A. Reddington, The American Society of Mechanical Engineers R. A. Schmidt, Trinity-Ladish Co. H. R. Sonderegger, Grinnell Corp. W. M. Stephan, Flexi

49、tallic, Inc. T. F. Stroud, Ductile Iron Pipe Research Association R. E. White, Richard E. White and Associates D. A. Williams, Southern Company Services L. A. Willis, The Dow Chemical Co. W. R. Worley, Union Carbide Corp. SUBCOMMITTEE J - COPPER AND COPPER ALLOY FLANGES, FLANGED FITTINGS, AND SOLDER JOINT FITTINGS M. A. Clark, Chair, Nibco, Inc. A. G. Kireta, Jr., Vice Chair, Copper Development Associatio