ASD-STAN PREN 6105-2006 Aerospace series Stud with shoulder (Edition P 1)《航空航天系列 有肩螺柱 第P1版》.pdf

《ASD-STAN PREN 6105-2006 Aerospace series Stud with shoulder (Edition P 1)《航空航天系列 有肩螺柱 第P1版》.pdf》由会员分享，可在线阅读，更多相关《ASD-STAN PREN 6105-2006 Aerospace series Stud with shoulder (Edition P 1)《航空航天系列 有肩螺柱 第P1版》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、ASD STANDARD NORME ASD ASD NORM prEN 6105 Edition P 1 December 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONGulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: Descriptors: ENGLISH VERSION Aerospace ser

2、ies Stud with shoulder Srie arospatiale Axe paulement Luft- und Raumfahrt Verschlubolzen mit Bund This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs o

3、f the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or function

4、ally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN

5、 national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 December 2006Comments should be sent within six months after the date of publica

6、tion to ASD-STAN Mechanical Domain Copyright 2006 by ASD-STAN prEN 6105:20062 Contents Page Foreword2 1 Scope 3 2 Normative references 3 3 Requirements.4 4 Designation 6 5 Marking .6 6 Technical specification .6 7 Example of installation6 Foreword This standard was reviewed by the Domain Technical C

7、oordinator of ASD-STANs Mechanical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 6105:20063 1 Scope This standard specifies the dimensions, tolerances, requ

8、ired characteristics and mass of a stud for use in fuselage interior equipment and structural applications. This standard shall be used in conjunction with retaining washer per EN6090A01 (conform to EN 6090) and receptacles per EN 6092 or EN 6093. 2 Normative references The following referenced docu

9、ments are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimen

10、sions without individual tolerance indications. EN 2424, Aerospace series Marking of aerospace products. EN 2516, Aerospace series Passivation of corrosion resisting steels and decontamination of nickel base alloys. EN 4318, Aerospace Series Heat resisting alloy FE-PA2601 (X6NiCrTiMoV26-15) Solution

11、 treated and precipitation treated Bar and section, De 100 mm, Rm 960 MPa. 1)EN 6090, Aerospace series Washer, retaining. 1)EN 6092, Aerospace series Receptacle, floating, double lug. 1)EN 6093, Aerospace series Receptacle, floating, single lug. 1)EN 6094, Aerospace series Washer, spring, countersun

12、k. 1)EN 6095, Aerospace series Rotary fasteners Structural and non-structural applications Technical specification. 1)SAE-AMS2700, Passivation of corrosion resistant steels. 2)SAE-AMS5629, Steel, corrosion-resistant, bars, wire, forgings, rings and extrusions, 13Cr - 8.0Ni - 2.2Mo - 1.1Al, vacuum in

13、duction plus consumable electrode melted, solution heat treated, precipitation hardenable. 2)SAE-AMS5737, Steel, corrosion and heat-resistant, bars, wire, forgings and tubing 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V, consumable electrode melted, 1 650 F (899 C) solution and precipitation heat

14、treated. 2)SAE-AS8879, Screw threads, UNJ profile, inch controlled radius root with increased minor diameter. 2)MIL-DTL-83488, Coating, aluminum, high purity. 3)MIL-S-7742, Screw threads, standard, optimum selected series: general specification for. 3)NASM33781, Recess-offset cruciform, dimensions o

15、f recess, and driver for. 4)1) Published as ASD Prestandard at the date of publication of this standard. 2) Published by: SAE International, 400 Commonwealth Drive, Warrendale, P.A., 15096-0001, USA 3) Published by: Department of Defense (DoD), the Pentagon, Washington, D.C., 20307, USA 4) Published

16、 by: Aerospace Industries Association of America, (AIA), 1250 Eye Street, N.W., Washington, D.C. 20005-3924, USA prEN 6105:20064 3 Requirements 3.1 Configuration, dimensions, tolerances and mass The configuration, dimensions, tolerances and mass shall conform to Figure 1 and Table 2. Dimensions and

17、tolerances are expressed in millimetres. Tolerances not specified shall be in accordance with ISO 2768-1. All dimensions and tolerances apply after surface treatment. All burrs to be removed / sharp edges to be broken. B B Optional version Key 1 Grip range. 3 Recess no. 10 per NASM33781 2 Marking, s

18、ee Clause 5. 4 0.1640-32UNJC-3B thread per SAE-AS8879, 2 lead or 0.1640-32UNC-3B thread per MIL-S-7742, 2 lead Figure 1 Configuration, dimensions and tolerances prEN 6105:20065 Table 1 Dimensions, tolerances and mass Grip range L X Z Mass (Ref) Size code min. max. 0,25 min. + 2,0 0 kg/1 000 pieces01

19、0 a3,81 4,59 10,92 8,0 1,63 015 4,60 6,39 11,71 9,0 1,70 020 6,40 7,35 12,70 9,8 5,0 1,83 030 7,36 9,15 14,48 11,4 7,0 2,04 040 9,16 10,90 16,26 12,0 2,31 050 10,91 12,70 18,03 2,55 060 12,71 14,50 19,81 2,91 070 14,51 16,25 21,59 3,26 080 16,26 18,00 23,37 3,62 090 18,01 19,80 25,15 3,97 100 19,81

20、21,60 26,92 4,30 110 21,61 23,38 28,70 4,66 120 23,39 25,16 30,48 5,01 130 25,17 26,93 32,26 5,37 140 26,94 28,72 34,04 5,70 150 28,71 30,50 35,82 6,06 160 30,51 32,29 37,60 13,0 8,0 6,42 aNot for new design 3.2 Material and surface treatment See Table 2. Table 2 Material and surface treatment Mater

21、ial Surface treatment Finish code Passivated per SAE-AMS2700 or EN 2516 - Corrosion resistant steel per SAE-AMS5629 H1050 or corrosion resistant steel per SAE-AMS5737 or heat resisting alloy per EN 4318 or equivalent IVD coating per MIL-DTL-83488 type II, class 3 V 3.3 Mechanical characteristics 3.3

22、.1 General All mechanical characteristics are valid in conjunction with receptacles per EN 6092 and EN 6093 only. prEN 6105:20066 3.3.2 Static values Ultimate tension load: 6 300 N NOTE Ultimate tension load of fastening system in combination with receptacle EN 6092 or EN 6093 is 6 000 N. Ultimate s

23、hear load: 9 000 N 3.3.3 Installation torque The installation torque with receptacles per EN 6092 and EN 6093 shall be 2,8 Nm to 3,2 Nm. 3.4 Operating temperature This stud shall be used in the temperature range of 55 C to 150 C. 4 Designation EXAMPLE Description block STUD Identity block EN6105-020

24、 Number of this standard Finish code (see Table 2) Size code (see Table 1) NOTE If necessary, the code I9005 shall be placed between the description block and the identity block. 5 Marking EN 2424, style C 6 Technical specification EN 6095 7 Example of installation See Figure 2. prEN 6105:20067 Key 1 Washer EN 6094 2 Panel 3 Washer EN6090A01 4 Stud EN 6105 5 Receptacle EN 6092 or EN 6093 Figure 2 Example of installation