ARMY UFGS-14 24 00-2010 HYDRAULIC ELEVATORS.pdf

《ARMY UFGS-14 24 00-2010 HYDRAULIC ELEVATORS.pdf》由会员分享，可在线阅读，更多相关《ARMY UFGS-14 24 00-2010 HYDRAULIC ELEVATORS.pdf（33页珍藏版）》请在麦多课文档分享上搜索。

1、*USACE / NAVFAC / AFCESA / NASA UFGS-14 24 00 (August 2010)-Preparing Activity: USACE SupersedingUFGS-14 24 00 (February 2009)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated July 2010*SECTION TABLE OF CONTENTSDIVISION 14 - CONVEYING EQUIPMENTSECTION 14 24 00HYDRAUL

2、IC ELEVATORS08/10PART 1 GENERAL1.1 REFERENCES1.2 SYSTEM DESCRIPTION1.2.1 Miscellaneous Requirements1.2.2 Provisions for Earthquake Protection1.3 SUBMITTALS1.4 QUALITY ASSURANCE1.4.1 Elevator Specialist1.4.2 Elevator Inspector1.4.3 Welders Qualifications1.4.4 Detail Drawings1.5 SCHEDULING1.6 WARRANTY

3、1.7 MAINTENANCE AND REPAIR ACTION PLAN1.7.1 Maintenance and Diagnostic Tools1.7.2 Keys for Elevator Key SwitchesPART 2 PRODUCTS2.1 PASSENGER ELEVATORS2.1.1 Basic Requirements2.1.2 Cab Enclosures and Door Finishes2.2 FREIGHT ELEVATORS2.2.1 Basic Requirements2.2.2 Cab Enclosures and Door Frame Finishe

4、s2.3 SPECIAL OPERATION AND CONTROL2.3.1 Firefighters Service2.3.2 Smoke Detectors2.3.3 Fire Sprinklers2.3.4 Top-of-Car Operating Device2.3.5 Hoistway Access Switches2.3.6 Independent Service2.3.7 Elevator Operation2.3.7.1 Single, Two-Stop, Automatic Operation2.3.7.2 Selective Collective Automatic Op

5、erationSECTION 14 24 00 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.3.7.3 Duplex Selective Collective Automatic Operations2.3.7.4 Group Automatic Operation2.3.8 Parking Switch2.3.9 Hospital Emergency Commandeering Service2.4 ELEVATOR DRIV

6、E SYSTEM2.4.1 Hydraulic Pump Unit2.4.1.1 Pump Motor2.4.2 Hydraulic Controls and Equipment2.4.2.1 Hydraulic Control Valve2.4.2.2 Hydraulic Overspeed Safety Valve2.4.2.3 Hydraulic Oil Scavenger Pump2.4.3 Hydraulic Piping and Accessories2.4.3.1 Containment of Hydraulic Oil Supply Line2.4.4 Hydraulic El

7、evator Type2.4.4.1 Cylinder-Plunger (Jack) Unit2.4.5 Cylinder Well System2.4.5.1 Well Casing2.4.5.2 PVC or HDPE Cylinder Liner2.4.5.3 Cylinder Installation2.4.5.4 Pressure Test of PVC Liner/Cylinder Assembly2.4.5.5 Cylinder Liner Water and Oil Sensor System2.4.5.6 Seal Top of Well Casing2.5 CONTROL

8、EQUIPMENT2.5.1 Motor Control Equipment2.5.1.1 Electrical Isolation Protection2.5.2 Logic Control Equipment2.5.2.1 On-Board Diagnostic Panel2.5.2.2 External Port2.5.2.3 Maintenance and Diagnostic Software2.5.2.4 Acceptable Controller Suppliers2.6 OPERATING PANELS, SIGNAL FIXTURES, AND COMMUNICATIONS

9、CABINETS2.6.1 Capacity and Data Plates2.6.2 Car and Hall Buttons2.6.3 Hall Station Door Operating Buttons2.6.4 Passenger Car-Operating Panel2.7 PASSENGER CONTROLS2.7.1 Passenger Car-Operating Panel2.7.1.1 Service Controls2.7.1.2 Certificate Window2.7.2 Freight Car-Operating Panel2.7.2.1 Passenger Co

10、ntrols2.7.2.2 Service Controls2.7.2.3 Certificate Window2.7.3 Semi-Selective Door Operation2.7.4 Full-Selective Door Operation2.7.5 Switches and Devices2.7.6 In-Car Position and Direction Indicator and Signal2.7.6.1 In-Car Position Indicator and Signal2.7.6.2 In-Car Direction Indicator and Signal2.7

11、.7 Landing Position and Direction Indicator and Signal2.7.7.1 Landing Position Indicator and Signal2.7.7.2 Landing Direction Indicator and Signal2.8 HOISTWAY AND CAR EQUIPMENT2.8.1 Guide Rails and Fastenings2.8.2 Car Buffers2.8.3 Pit Equipment2.8.3.1 Pit “STOP“ Switch2.8.3.2 Ladders2.8.3.3 Lighting

12、of PitsSECTION 14 24 00 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.9 TERMINAL STOPPING DEVICES2.9.1 Wiring and Traveling Cables2.9.2 Emergency Signaling Device2.10 PASSENGER CAR AND HOISTWAY DOOR ACCESSORIES2.11 PASSENGER ELEVATOR GUIDES

13、, FRAME, PLATFORM, AND ENCLOSURE2.11.1 Roller Guides2.11.2 Car Enclosure, Car Door, and Car Illumination2.11.2.1 Return Panels, Entrance Columns, Cove Base, and Transom2.11.2.2 Car Top2.11.2.3 Car Door2.11.2.4 Car Entrance Sill2.11.2.5 Carpet2.12 PASSENGER ELEVATOR HOISTWAY DOORS AND ENTRANCES2.12.1

14、 Hoistway Entrance Frames2.12.2 Hoistway Entrance Sills2.12.3 Hoistway Entrance Doors2.12.4 Entrance Fascias and Dust Covers2.12.5 Hoistway Ventilation2.13 FREIGHT ELEVATOR GUIDE SHOES, PLATFORM, AND ENCLOSURE2.13.1 Roller Guides2.13.2 Car Enclosure2.14 FREIGHT ELEVATOR HOISTWAY DOORS AND ENTRANCES2

15、.14.1 Door Panel2.14.2 Door Operation2.15 HANDICAPPED AND MEDICAL SERVICES ACCESS2.15.1 Provision For Handicapped2.15.2 Emergency Medical Service2.16 EMERGENCY POWER OPERATIONPART 3 EXECUTION3.1 INSTALLATION3.1.1 Traveling Cables3.1.2 Automatic Shutoff Valve3.1.3 Structural Members3.1.4 Safety Guard

16、s3.1.5 Other Requirements3.2 FIELD QUALITY CONTROL3.2.1 Testing Materials and Instruments3.2.2 Field Tests3.2.2.1 Endurance Tests3.2.2.2 Automatic Shutoff Valve Tests3.2.2.3 Speed Tests3.2.2.4 Leveling Tests3.2.2.5 Pressure Tests3.2.2.6 Insulation Resistance Tests3.2.2.7 Temperature Rise Tests3.2.2.

17、8 Motor Ampere Tests3.3 OPERATION AND MAINTENANCE TRAINING- End of Section Table of Contents -SECTION 14 24 00 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-14 24 00 (August 2010)-Preparing Activity: USACE

18、 SupersedingUFGS-14 24 00 (February 2009)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated July 2010*SECTION 14 24 00HYDRAULIC ELEVATORS08/10*NOTE: This guide specification covers the requirements for hydraulic passenger and freight elevators.Edit this guide specific

19、ation for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert appropriate information.Remove information and requirements not required in respective project, whether or not brackets are present.Comments and suggestions on thi

20、s guide specification are welcome and should be directed to the technical proponent of the specification. A listing of technical proponents, including their organization designation and telephone number, is on the Internet.Recommended changes to a UFGS should be submitted as a Criteria Change Reques

21、t (CCR).*PART 1 GENERAL*NOTE: For NAVFAC projects, any editing of non-bracketed paragraphs in this specification must be approved through the NAVFAC Elevator Program.The designer will incorporate the following features into the design and will show in the drawings as applicable.1. Complete design of

22、 the hoistways, pits, machine rooms including all structural requirements, sizing, access, fire-resistant rating, ventilation, waterproofing and drainage.SECTION 14 24 00 Page 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2. Proper size of opening

23、s into hoistway walls for installing hoistway door assemblies.3. Storage facilities for elevator equipment during construction.4. Electrical service requirements for elevators, including sizings in compliance with codes and locations for fused and unfused disconnect switches.5. Sill supports, includ

24、ing steel angles, sill recesses, and grouting of door sills.6. Structural steel door frames with extensions to beams.7. Locations for hall stations and hall lanterns.8. Emergency power supply with automatic time-delay transfer switch and auxiliary contacts with wiring to elevator controller.9. Telep

25、hone and or Intercom connections to elevator hoistway.10. Location of smoke detectors required for Firefighters Service. The designer will also indicate wiring of the smoke detectors to the elevator control system and to the building fire alarm system.11. Wiring to elevator alarm bells and fire-figh

26、ters service.12. Lighting, ventilation and heat to machine room. Ambient temperature of 10 degrees C (50 degrees F) min., 32 degrees C (90 degrees F) max.*1.1 REFERENCES*NOTE: This paragraph is used to list the publications cited in the text of the guide specification. The publications are referred

27、to in the text by basic designation only and listed in this paragraph by organization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RID outside of the Sections Reference Article to automatically place the reference in the Reference Article. Also use t

28、he Reference Wizards Check Reference feature to update the issue dates.References not used in the text will automatically be deleted from this section of the project SECTION 14 24 00 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-specification

29、 when you choose to reconcile references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.AMERICAN WELDING SOCIETY (AWS)AWS D1.1/D1.1M (2010) Structur

30、al Welding Code - SteelASME INTERNATIONAL (ASME)ASME A17.1/CSA B44 (2007; Addenda a 2008) Safety Code for Elevators and EscalatorsASME A17.2 (2007) Guide for Inspection of Elevators, Escalators, and Moving WalksASME B16.11 (2009) Forged Fittings, Socket-Welding and ThreadedASME B16.9 (2007) Standard

31、 for Factory-Made Wrought Steel Buttwelding FittingsASTM INTERNATIONAL (ASTM)ASTM A 106/A 106M (2008) Standard Specification for Seamless Carbon Steel Pipe for High-Temperature ServiceASTM A 53/A 53M (2007) Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamles

32、sINTERNATIONAL CODE COUNCIL (ICC)ICC IBC (2009; Errata First Printing) International Building CodeNATIONAL ELEVATOR INDUSTRY, INC. (NEII)NEII-1 (2000; R thru 2010) Building Transportation Standards and Guidelines, including the Performance Standards Matrix for New Elevator InstallationNATIONAL FIRE

33、PROTECTION ASSOCIATION (NFPA)NFPA 252 (2008) Standard Methods of Fire Tests of Door AssembliesNFPA 70 (2008; TIA 08-1) National Electrical CodeU.S. NATIONAL ARCHIVES AND RECORDS ADMINISTRATION (NARA)29 CFR 1910.27 Fixed LaddersSECTION 14 24 00 Page 6Provided by IHSNot for ResaleNo reproduction or ne

34、tworking permitted without license from IHS-,-,-36 CFR 1191 Americans with Disabilities Act (ADA) Accessibility Guidelines for Buildings and Facilities1.2 SYSTEM DESCRIPTIONProvide a pre-engineered elevator system, by manufacturer regularly engaged in the manufacture of elevator systems, that compli

35、es with ASME A17.1/CSA B44 and ASME A17.2 in their entirety, and additional requirements specified herein.1.2.1 Miscellaneous RequirementsSubmit one set of wiring diagrams, in plastic or glass cover, framed and mounted in elevator machine room for revised building electrical system, if needed, to ma

36、ke supplied elevator system function as specified. Deliver other sets to Contracting Officer. Coded diagrams are not acceptable unless adequately identified. Submit calculations for the Reaction Loadsimposed on the building by and Heat Loads generated by the elevator system.1.2.2 Provisions for Eart

37、hquake Protection*NOTE: Provide seismic protection as covered by ASME A17.1/CSA B44, Section 8.4. Provide fastenings, attachments, and restraints for prevention of seismic damage in detail by registered structural engineer whose seal is applied to drawings or sketches. Use forces of 1.0 G horizontal

38、 and 1.0 G vertical or heavier.*The facility is located in a seismic zone 3 4, and shall comply with all ASME A17.1/CSA B44, Part 8.4 requirements.1.3 SUBMITTALS*NOTE: Review submittal description (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only t

39、he submittals required for the project. Submittals should be kept to the minimum required for adequate quality control.A “G” following a submittal item indicates that the submittal requires Government approval. Some submittals are already marked with a “G”. Only delete an existing “G” if the submitt

40、al item is not complex and can be reviewed through the Contractors Quality Control system. Only add a “G” if the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army projects, a code of up to three characters within the submitt

41、al tags may be used following the “G“ designation to indicate the approving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for SECTION 14 24 00 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Architect-E

42、ngineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“ for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes following the “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracketed item fo

43、r Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.*Government approval is required for submittals with a “G“ designation; submittals not having a “G“ designation are for Contractor Quality Control approval. information only. When used, a designation following

44、 the “G“ designation identifies the office that will review the submittal for the Government. Submit the following in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:SD-02 Shop DrawingsDetail Drawings; G; G, _SD-03 Product DataPassenger Elevators; G; G, _Freight Elevators; G; G, _Information on motor, pump, gages, piston and cylinder, piping and valves, hall station, and buffer on elevators and accessories. For elevator supporting systems, include information on car control and emergency power systems. On data sheets, provide document identification number or bulletin number, pub