ARMY OO-D-735 C-1973 DRYCLEANING FINISHING EQUIPMENT MISCELLANEOUS《杂项干洗完成设备》.pdf

《ARMY OO-D-735 C-1973 DRYCLEANING FINISHING EQUIPMENT MISCELLANEOUS《杂项干洗完成设备》.pdf》由会员分享，可在线阅读，更多相关《ARMY OO-D-735 C-1973 DRYCLEANING FINISHING EQUIPMENT MISCELLANEOUS《杂项干洗完成设备》.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、00- D 735c January 11, 1973 QUPERSEDIN G Fed. Spec. OO-D735B July 12, 1971 and Fed. Spec. OO-D73OA (In Part) November 15, 1966 (See 6.5) FEDERAL SPECIFICATION DRYCLEANING FINISHING EQUIPMENT, MISCELLANEOUS This specification was approved by the Commissioner, Federal Supply Service, General Services

2、Administration, for the use of all Federal agencies. 1. SCOPE AND CLASSIFICATION 1.1 Scope. This specification covers commercialmiscellaneous drycleaning finishing equipment which can be safely used in nonhazardous locations only (see 6.1). 1.2 Classification. The miscellaneous drycleaning finishing

3、 equipment covered by this specification shall be of the following items, classes, and sizes as specified (see 6.2 and 6.5): Item: 1- 2- 3- 4- 5- 7- 8- 9- 10 - Air vacuum unit (see 3.7.1). Class 1 - Horizontal type. Class 2 - Vertical type. Bag, sleever (see 3.7.2). Finishing board (see 3.7.3). Clas

4、s 1 - With flatiron. Class 2 - Without flatiron. Garment finisher (see 3.7.4) . Flatiron, electric, steam (see 3.7.5). Size - 3 to 4 pounds. Size - 5-112 to 6-112 pounds. Spotting board (see 3.7.6). Coat Finisher, Automatic (see 3.8). Cabinet, Drying and Deodorizing (see 3.9). Reel Sorting (see 3.10

5、). FSC 3510 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-00-D-735C 2. APPLICABLE DOCUMENTS 2.1 The following documents, of the issues in effect on date of invitation or bids or request for proposal, form a part of this specification to the extent

6、specified herein: Federal Specifications: CC-M-6 36 - Motor, Alternating-Current, (Fractional Horsepower). CC-M-641 - Motor, Alternating-Current, (Integral Horsepower, QQ-C-390 - Copper Alloy Castings (Including Cast Bar). QQ-N-2 81 - Nickel-Copper-Alloy Bar, Plate, Rod, Sheet, Strip, Wire, Forgings

7、, and Structural and Special Shaped Sections. Castings . 200 Hp and Smaller). QQ-N- 2 8 8 - Nickel-Copper Alloy and Nickel-Copper-Silicon Alloy Federal Standard: FED-STD-123 - Marking for Domestic Shipment (Civil Agencies). (Activities outside the Federal Government may obtain copies of Federal Spec

8、ifications, Standards, and Handbooks as outlined under General Information in the Index of Federal Specifications and Standards and at the prices indi- cated in the Index. The Index, which includes cumulative monthly supplements as issued, is for sale on a subscription basis by the Superintendent of

9、 Docu- ments, U.S. Government Printing Office, Washington, DC 20402. (Single copies of this specification and other Federal Specifications re- quired by activities outside the Federal Goveriimenlt for bidding purposes are available without charge from Business Service Centers at the General Services

10、 Administration Regional Offices in Boston, New York, Washington, DC, Atlanta, Chicago, Kansas City, Mo, Fort Worth, Denver, San Francisco, Los Angeles, and Seattle, WA. (Federal Government activities may obtain copies of Federal Specifications, Standards, and Handbooks and the Index of Federal Spec

11、ifications and Standards from established distribution points in their agencies .) Military Specifications: MIL-T-152 - Treatment, Moisture and Fungus-Resistant, of Com- munications, Electronic, and Associated Electrical Equipment. 2 Provided by IHSNot for ResaleNo reproduction or networking permitt

12、ed without license from IHS-,-,-00-D-735C 35 7777774 0024517 1 O 00-D-735C MIL-L-315 3 - Laundry and Dry-cleaning Machinery and Equipment (For Fixed Installations), Preparation for Delivery for Domestic and Overseas Shipment. Military Standards: MIL-STD-105 - Sampling Procedures and Tables for Inspe

13、ction by MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-130 - Identification Marking of U.S. Military Property. MIL-STD-461 - Electromagnetic Interference Characteristics, MIL-STD-462 - Electromagnetic Interference Characteristics, Attribut es. Requirements for Equipment. Measurement Of. (C

14、opies of Military Specifications and Standards required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other publications. The following documents form a part of this specification to the e

15、xtent.specified herein. Unless a specific issue is identified, the issu2 in effect on date of invitation for bids or request for proposal shall apply: Underwriters Laboratories (UL) , Inc., Standards : (Application for copies of applicable UL standards should be addressed to the Underwriters Laborat

16、ories, Inc., 1285 Walt Whitman Road, Melville, Long Island, N.Y., 11746; 207 East Ohio St., Chicago, Ill., 60611; or 1655 Scott Blvd., Santa Clara, CA 95050.) American Welding Society (AWS) Standard: Qualification Procedures of the American Welding Society. (Application for copies should be addresse

17、d to the American Welding Society, United Engineering Center, 345 East 47th St., New York, NY 10017.) American Society of Mechanical Engineers (ASME) Standards: ASME Boiler and Pressure Vessel Code, Section VI11 - Unfired Pressure Vessels. Welding Qualifications of the American Society of Mechanical

18、 Engineers. (Application for copies should be addressed to the American Society of Mechanical Engineers, United Engineering Center, 345 East 47th St., New York, NY 10017.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-00-D-735C 35 m 7777779 00295

19、20 m 00-D-735C American Society for Testing and Materials (ASTM) Standards: A167-70 - Corrosion-Resisting Chromium-Nickel Steel A176-71 - Corrosion-Resisting Chromium Steel, Plate, Plate, Sheet and Strip. Sheet and Strip. (Application for copies should be addressed to the American Society for Testin

20、g and Materials, 1916 Race Street, Philadelphia, PA 191 03. ) National Fire Protection Association (NFPA) Standard: No. 70 - National Electrical Code. (Application for copies should be addressed to the National Fire Protection Association, 60 Batterymarch St., Boston, MA 02lIO.) National Electrical

21、Manufacturers Association (NEMA) Standard: ICs - Industrial Controls and Systems. (Application for copies should be addressed to the National Electrical Q Manufacturers Association, 155 East 44th Street, New York, Ny 10017.) (Technical society and technical association specifications and standards a

22、re generally available for reference from libraries. buted among technical groups and using Federal agencies.) They are also distri- 3. REQUIREMENTS 3,l First article. a sample of the item to be procured under this specification for first article inspection and approval (see 4.3 and 6.4). When speci

23、fied (see 6.2), the supplier shall furnish 3.2 Standard product. The item(s) delivered under this specification shall be the manufacturers commercial product, except for any changes necessary to comply with specification requirements. contract, including parts and subassemblies thereof shall be new

24、and inter- changeable. All like items furnished on any one 3.3 Codes and standards-. The item(c) shall comply with the applicable requirements of UL Standards, NEMA Publication ICs 1970, NFPA Standard No. 70 and ASME Code for Unfired PRESSURE Vessels, when applicable. submitted, or prior to commenci

25、ng production, the supplier shall submit to 3.4 Compliance, Prior to approval of the first article, if one is Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-00-D-735C the contracting officer or his authorized representative satisfactory evidence tha

26、t the item(s) that he proposes to furnish under this specification meet the applicable requirements of UL Standards, NEMA ICs, “PA NO. 70, and ASME Standard for Unfired Pressure Vessels, when applicable. 3.4.1 NFPA. Acceptable evidence of meeting requirements of NFPA shall be the manufacturers certi

27、fied statement that the drycleaning finishing equip- ment is wired in accordance with NFPA No. 70, when applicable. 3.4.2 UL. Acceptable evidence of meeting requirements of UL shall be the UL label or a UL listing mark or a certification from an independent testing laboratory acceptable to the contr

28、acting officer or hfs authorized representative that the wiring, fittings, and conduit conform to applicable UL standards, when applicable. 3.4.3 NEHA. Acceptable evidence of meeting the requirements of NEMA shall be the manufacturers certified statement that the motor controllers, switches, relays,

29、 time d.elays, and solenoids conform to performance requirements of NEMA ICs. A tag or label attached to these components stating they conform to this standard is acceptable evidence. 3.4.4 ASME. Acceptable evidence of meeting the requirements of ASME, when applicable, shall be the manufacturers cer

30、tified statement. that the chests, chambets and cylinders are in compliance with the ASME Standard for Unfired Pressure Vessels. 3.5 Materials and components. Materials and components shall be as specified herein (and on applicable drawings). Materials not definitely specified shall be of the qualit

31、y normally used by the manufacturer in the standard commercial items(s) provided that the completed items(s) comply with all provisions of this specification. 3.5.1 Corrosion-resistant metal. Corrosion-resistant metal used in the fabrication of the finishing equipment shall be corrosion-resisting st

32、eel conforming to the requirements of ASTM Al67-70 or Al76-71, as applicable; nickel-copper-alloy conforming to QQ-N-281 or composition A of QQ-N-288; or copper alloy castings conforming to alloy numbers el through G8 Of QQ-C-390. 3.5.2 Materials for fasteners. Threaded fasteners and rivets shall be

33、 of carbon or alloy steel, except where brass or corrosion-resistant metal is to be fastened, in which case they shall be of brass or corrosion-resistant metal respectively (see 3.5.1). Where dissimilar metals are fastened, bolts, rivets, screws, and nuts shall be of corrosion-resistant metal (see 3

34、.5.1). 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-00-D-735C 35 7777774 O024522 H 00-D-735C 3.5.3 Pipe, tube, fittings, and valves. Pipe, tube, fittings, and valves used for water, steam, and condensate lines shall comply with accepted plumbing

35、 practice. 3.5.4 Electrical conduit, fittings, and wire. Electrical conduit shall be rigid, electrical metallic tube or liquid-tight flexible conduit. electrical wire shall be stranded copper, heat-resistant grade, thermoplastic insulated. Solid (nonstranded) wire shall not be used. All 3.5.5 Motors

36、. Motors shall be drip proof for operation in a 40 Centigrade (C) ambient temperature. Motors shall conform to the require- ments of CC-M-636 or CC-M-641, as applicable, and to the following-require- ments : (a) All motors shall have windings impregnated to resist moisture. (b) Each motor of 1/8 hor

37、sepower rating or larger shall be provided with manually reset thermal-overload protection incorporated as a part of the motor or installed in the controller. (c) Motors shall be equipped with ball bearings, except that motors of 1/2 horsepower or less when used in a horizontal application may have

38、sleeve bearings. (d) Motor bearings shall be a permanently lubricated type or shall have adequate and accessible means for lubrication. 3.6 Design and construction. The drycleaning finishing equipment shall be designed for use fn a nonhazardous area. The completely assembled items when tested as spe

39、cified in 4.6.4 shall show that assembly of components has: (a) Complete and proper interrelationship. (b) No leaks, (c) (d) No overheating of parts (e.g., bearings). (e) (f) No structural failures. No undue vibration or noise. Starting and stopping devices operate smoothly and positively. 3.6.1 Wlr

40、ing. Wiring shall be provided between motors, controllers, and switches installed on the equipment with materials specified in 3.5.4 as applicable. connections beyond the item of equipment. by a different color or shall be clearly labeled. showing any necessary connections required beyond the equipm

41、ent shall be furnished with each item of equipment using electric power. All wiring shall terminate in connection boxes with provisions for Each conductor shall be identified Wiring and connection.diagrams 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

42、S-,-,-00-D-7 35C 3.6.2 Steam pressures. Assemblies of pipes, fittings, coils, cylinders, chests, and chambers using steam except for item 8 shall be designed for 100 pounds per square inch gage (psig) working pressure and shall be capable of withstanding a 200 psig hydrostatic pressure without leaks

43、 when tested as specified in 4.6.1. 3.6.3 Lubrication. Lubrication fittings for force-type systems shall be provided and accessibly located for lubricating bearings (see 3.5.5 (d) for motor -exception). 3.6.4 Current characteristics. The electrical parts of machines shall be designed for the voltage

44、, frequency, and number of phases specified (see 6.2). Operational and functional testing shall be performed at the voltage, frequency and number of phases specified. 3.6.5 Electromagnetic compatibility. When specified (see 6.2), equipment shall be designed and equipped for electromagnetic compatibi

45、lity in accord- ance with class IIB of MIL-STD-461 (see 4.6.7). 3.6.6 Finish. Unless otherwise specified (see 6.2), items of equipment shall be finished according to the manufacturers standard practice except emergency stop and nornial stop pushbuttons shall be red and this color shall be limited to

46、 pushbuttons. 3.6.7 Moisture and fungus-resistant treatment. When specified (see 6.2), electrical components of equipment covered by this specification shall be moisture and fungus-resistant treated with material conforming to and applied as specified in MIL-T-152. 3.6.8 Identification marking. For

47、military procurements, each end item shall be marked in accordance with MIL-STD-130. marking shall be in accordance with the manufacturers standard practice. For civil agency procurement, 3.7 Detail requirements. 3.7.1 Item 1 - air vacuum unit (for air vacuum presses). The vacuum system shall be the

48、 horizontal type (class i) or the vertical type, (class 2) as stated in 1.2. Each class 1 and 2 unit shall consist of an electric- motor-driven (see 3.5.5) multistage centrifugal-type exhauster and a condenser tank. The number of presses that the air vacuum unit is to service shall be as specified (

49、see 6.2). The exhauster shall be capable of maintaining a vacuum at sea level equivalent to 3/4-inch water column on 40 percent of the presses to be serviced and with these presses operating. shall be determine when tested as specified in 4.6.3. This requirement 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-00-D-735C 35 7779974 0024524 5 W 00-D-7 35C 3.7.1.1 Exhausters. The he