ARMY MIL-W-46154 (1)-1994 WELDING RESISTANCE SPOT AND PROJECTION FOR FABRICATING ASSEMBLIES OF CARBON STEEL SHEETS《碳钢薄片的装配组装的点投影 电阻器 定位焊接》.pdf

《ARMY MIL-W-46154 (1)-1994 WELDING RESISTANCE SPOT AND PROJECTION FOR FABRICATING ASSEMBLIES OF CARBON STEEL SHEETS《碳钢薄片的装配组装的点投影 电阻器 定位焊接》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-W-46154 (1)-1994 WELDING RESISTANCE SPOT AND PROJECTION FOR FABRICATING ASSEMBLIES OF CARBON STEEL SHEETS《碳钢薄片的装配组装的点投影 电阻器 定位焊接》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-W-46154 (1) 06 1989407 T57 W INCH-POUND MIL-W-46154(MR) AMENDMENT 1 30 August 1994 MILITARY SPECIFICATION WELDING, RESISTANCE, SPOT AND PROJECTION FOR FABRICATING ASSEMBLIES OF CARBON STEEL SHEETS This amendment forms a part of MIL-W-46154(MR), dated 20 October 1970, and is approved for use by t

2、he US Army Research Laboratory/Materials Directorate, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 2.1: Delete and substitute: “2.1 Government documen tg. The following specification forms a part of this document to the extent specified herein. Unless

3、 otherwise specified, the issues of this documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation. SPECIFICATION MILITARY MIL-1-45208 - Inspection Requirements, General Specification for (Unl

4、ess otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.)“ 2.2: Delete and substitute: “2.2 Non - Government DUbbtia . The following documen

5、ts form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DODISS cited in the solicitation. of documents not listed in the DODISS are the issues of the documents cited in the soli

6、citation. Unless otherwise specified, the issues AMERICAN WELDING SOCIETY (AWS) AWS A2.4 - Standard Symbols for Welding, Brazing, and Nondestructive Examination ASMC N/A 1 of 2 AREA THJM PISTRIBTION STATEMEXT 4 Approved for public release; distribution unlimited. Licensed by Information Handling Ser

7、vicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-46154(MR) AMENDMENT 1 PAGE 1 AWS A3.0 - Standard Welding Terms and Definitions (Applications for copies should be addressed to the American Welding Society, 550 N.W. LeJeune Road, Miami, FL 3

8、3126).“ PAGE 2 3.1, lines 5 through 7: Delete and substitute: “:-li6 information shall be prepared in duplicate on an approved form (see appendix) using symbols and terms in accordance with AWS A2.4 and AWS A3.0, or as specified in the drawing.“ PAGE 3 4.1: Delete and substitute: “4.1 mbon con tent.

9、 The carbon content of any material to be welded shall be in the range of 0.40 to 0.60 percent (see 8.4). Cu6 todian: Amy - MR Review activities: Army - AL, AR, AT, ME, MI Preparing activity: Army - MR (Project TJM-A340) WP# I .D-0418A/DISC-0119A. FOR ARL/MD USE ONU. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-