ARMY MIL-S-63326 (6)-1994 SAFETY AND ARMING ASSEMBLIES FOR MINES BLU-91 B AND BLU-92 B《BLU-91 B和BLU-92 B型地雷的安全和武装装配》.pdf

《ARMY MIL-S-63326 (6)-1994 SAFETY AND ARMING ASSEMBLIES FOR MINES BLU-91 B AND BLU-92 B《BLU-91 B和BLU-92 B型地雷的安全和武装装配》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-S-63326 (6)-1994 SAFETY AND ARMING ASSEMBLIES FOR MINES BLU-91 B AND BLU-92 B《BLU-91 B和BLU-92 B型地雷的安全和武装装配》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-63326 (AR) AMENDMENT 6 27 December 1994 SUPERSEDING AMENDMENT 5 17 April 1989 MILITARY SPECIFICATION POWER SUPPLY ASSEMBLIES FOR FASCAM ELECTRONIC ASSEMBLIES This amendment forms a part of MIL-S-63326 (AR), dated 11 August 1981, and is approved for use by the U.S. Army Armaments Research, Deve

2、lopment and Engineering Center, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 2.1, Specification, Federal: Delete IQQ-S-465“ and substitute IQQ-S-365“. PAGE 2 * 2.1, Issues of documents: Specifications, Military: Delete “MIL-S-63457 - Soldering, . and

3、Electronic Equipment“ in its entirety. Standards, Military: Add the following Military Standard: “MIL-STD-2000 - Standard Requirements for Soldered Electrical and Electronic Assemblies“. PAGE 4 3.6.1, Under Temperature: Delete ii+700 + 10Fii and substitute “+70F +. 1OoF (Ambient) l. Delete “140O + 5

4、F“ and substitute “+1450F + 5OF“. 1 of 12 AMSC N/A FSC 1345 DISTRIBUTION STATEMEN T 4. Approved for public release: distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-b332b (6) 999990b 39bb14 185 = MIL-S-63326 (AR) AMEND

5、MENT 6 PAGE 4 (Contad) 3.6.2: Delete “partucular“ and substitute “particular“. Under Temperature: Delete “+70 + 10F“ and substitute “Ambient“. Delete “+1400 + 5Fii and substitute “+14SF + SF“. 3.8: Delete I .than O. 015 ohm. I and substitute II. . .than 0.15 ohm.“. PAGE 8 TABLE I: S&A Assembly and C

6、omponents: Delete “Microminature“ and substitute “Microminiature“. PAGE 11 TABLE I, S&A Assembly, Examination for Defects: Delete “4.4.2.45 (a) I and substitute 14. 4.2.47 (a) . Note (a): Delete “4.4.2.41, 4.4.2.43, been performed“ and substitute “4.4.2.41, 4.4.2.43 and 4.4.2.45 have been performed“

7、. Note (b) : Delete “70 2 100F“ and substitute “Ambient“. PAGE 12 Note (a): Delete “4.4.2.42 and 4.4.2.41 been performed“ and substitute “4.4.2.41, 4.4.2.42 and 4.4.2.44 have been performed“. Note (b) : Delete “700 f. 10F“ and substitute “Ambient“. PAGE 16 4.4.2.2, Borerider: Add the following Major

8、 Category: “122 Chamfer on tines missing . 0.40% . 3.2 . Visual“. PAGE 17 4.4.2.3, Spring Borerider: Minor 201: Delete “3.10“ and substitute “3.2“. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-63326 (6) m Ob 3996b35 OLL m MIL-S-63326 (AR)

9、AMENDMENT 6 PAGE 18 4.4.2.4, Interlock, Assembly: Major 101: Delete in its entirety. Major 201: Delete “3.2“ and substitute “3.10“. PAGE 19 4.5.2.5, Pin, Interlock: Minor 203: Delete in its entirety and substitute “Chamfers missing . 0.65% . 3.2 . Visual“. PAGE 21 4.4.2.7, Cup, Interlock: Add the fo

10、llowing Major Category: “109 Hardness test . 0.40% . 3.2 . ASTM E-18“. Minor 203: Delete “3.2“ and substitute “3.10“. PAGE 22 4.4.2.8, Slider Assembly: Major 102: Delete Gage“ and substitute “Visual“. Major 103: Delete “Gage“ and substitute “Visual“. Major 104: Delete in its entirety. Major 106: Aft

11、er staked add “(-1 assy only)“. PAGE 23 4.4.2.9, Cup Slider: Major 114: Delete “Depth of notch“ and substitute “Length from notch to tabs“. PAGE 31 4.4.2.15, Flexible Cable Assembly: * Major 106: Delete “Visual, MIL-S-45743“ and substitute “Visual, MIL-STD-2000“. Major 107: Delete “Gage“ and substit

12、ute “Visual“. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-63326 (6) 0b Lbblb T58 MIL-S-63326 (AR) AMENDMENT 6 PAGE 32 4.4.2.16, Flexible Cable Assembly: * Major 105: Delete “Visual, MIL-S-45743“ and substitute “Visual, MIL-STD-2000“. Majo

13、r 106: Delete ilGagel and substitute “Visual“. PAGE 33 4.4.2.17, Cable Flexible: Major 107: Delete “Soldering poor or incorrect“ and substitute “Solder coating poor or incorrect“. Add the following Major Category: “115 Solderability . 10-0-1 . 3.2 . Visual“. PAGE 34 4.4.2.18, Clip Ground: Note a: De

14、lete “Accept D“ and substitute “Accept O“. PAGE 35 4.4.2.19, Actuator, Microminiature Piston: Piston actuator function test: Delete “-60“ and substitute II -65oF Major 103: Delete “4.5.6.3“ and substitute “4.5.3.3“. Major 104: Delete “4.5.6.3“ and substitute “4.5.3.3“. Major 105: Delete “4.5.6.3“ an

15、d substitute “4.5.3.3“. Major 106: Delete “4.5.6.1“ and substitute “4.5.3.1“. Major 108: Delete “4.5.6.2“ and substitute “4.5.3.2“. Minor 201: Delete Il3.2“ and substitute 113.1011. PAGE 36 4.4.2.20, MDF Assembly: Major 107 : Delete “4.5.8.2 and substitute “4.5.4.2 . Minor 201: Delete “3.2“ and subs

16、titute “3.10“. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-63326 (61 9999906 L99bbL7 99Li - MIL-S-63326 (AR) AMENDMENT 6 PAGE 39 4.4.2.23, MDF, PBXN-5 Lead Sheathead: Major 102 : Delete 8t4.5.10“ and substitute *4.5.6“. PAGE 40 4.4.2.24,

17、Lower Housing Assembly: Next Higher Assembly: Delete “9328693/9328743“ and substitut e I 9 3 2 8 6 9 2 / 9 3 2 87 4 3 I . Minor 201: Delete “3.2“ and substitute “3.10“. PAGE 41 4.4.2.25, Housing, Lower, Sheet 1 of 4: Major 106: Delete I (See E-E) II and substitute I (See G-G) l. Major 107: Delete “(

18、See E-E) I and substitute (See G-G)“. Number of sample units column: Delete NOTE: Delete in its entirety. PAGE 42 4.4.2.25, Housing, Lower, Sheet 2 of 4: Major 120: Delete in its entirety. Major 121: Delete in its entirety. Major 125: Add I, 2 places“ after “hole“. Major 128: Add II, 2 places“ after

19、 “hole“. Major 129: Add II, 2 places“ after “hole“. Major 130: Delete “well“ and substitute “wells (detonator and delay detonator) . II Major 131: Add I, 2 places“ after “hole“. Major 138: Delete “(a) - 3.2 4.5.4“ and substitute “I/ . . .3.2 . . .4.5.1“ * Add the following note: “1/ Sampling and rej

20、ection shall be in accordance with MIL-T-12879“. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-63326 (AR) AMENDMENT 6 PAGE 43 4.4.2.25, Housing, Lower, Sheet 3 of 4: Note a: Delete in its entirety. PAGE 44 4.4.2.25, Housing, Lower, Sheet 4

21、of 4: Major 167: Delete in its entirety. Add Major 175: “Location of interlock assembly notch . . .O .40% . . -3.2 . . .Gage“. Add Major 176: “Width of interlock assembly notch . 0.40% . . -3.2 . . .Gage“ . Minor 202: Delete in its entirety. Minor 204: Delete “.notch incorrect“ and substitute Il .no

22、tch missing or incorrect“. PAGE 45 4.4.2.26, Upper Housing Assembly: Minor 201: Delete “3.2“ and substitute “3.10“. PAGE 46 4.4.2.27, Housing, Upper, Sheet 1 of 5: Major 114: Delete “(Sec T-T, Sht. 3)“ and substitute “(Sec T-T, Sht. 6)“. PAGE 47 4.4.2.27, Housing, Upper, Sheet 2 of 5: Major 127: Del

23、ete “.cap counter bore, 2 places (Sht. 2)“ and substitute Il . cap flash hole, 2 places (Sht. 2) II. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-b332b (b) = 0b 1996619 767 MIL-S-63326 (AR) AMENDMENT 6 PAGE 48 4.4.2.27, Housing, Upper, She

24、et 3 of 5: Major 142: Delete “4.5.4“ and substitute “4.5.1“. Major 143: Delete I (Sec S-3, Sht. 6) II and substitute “(Sec S-S, Sht. 6). Major 144: Delete in its entirety. Major 149: Delete “Distance . section“ and substitute “Distance from center of slider release pin cavity semicircular section to

25、 centerline of datum -A-“. PAGE 55 4.4.2.32, Pin, Shear Borerider: Add the following Major Category: “104 Head thickness . . . O .40% . . .3.2 . . .Gage“ , PAGE 58 4.4.2.35, Cup, Centrifugal Lock: Drawing Number: Delete “9328819“ and substitute “9329819“. PAGE 59 4.4.2.36, MDF Spacer: Major 102: Del

26、ete “Profile of side“ and substitute “Profile incorrect“. Major 103: Delete in its entirety. Major 104: Delete in its entirety. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-b332b (b) = 9999906 Lbb20 489 MIL-S-63326 (AR) AMENDMENT 6 PAGE 60

27、 4.4.2.37, Spacer Actuator: Major 106: Delete “Diameter of cavity (Sec A-A)“ and substitute “Depth of diameter located to DATUM A (Sec A-A) II. Minor 202: Delete “3.10“ and substitute “3.2“. Minor 203: Delete in its entirety. PAGE 61 4.4.2.38, Shield: Minor 201: Delete “Gage“ and substitute “Visual“

28、. PAGE 63a * 4.4.2.40.1, Add new paragraph as follows: “4.4.2.40.1: Classification of Defects and Tests for Packing and Marking for Box, Fiberboard for Safety and Arming Assembly, Drawing Number 12937990.“ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

29、,-,-41 IA O 4 k -cl cdE x!-l 4 a Ca cdc cd m cs -4 ci -vu =aid .lm jr a, Ici :I- -4 -4 -4 -4 -4 -4 E-? OiPdPBdPdP dP 00000 a WWTrTrTr W 00000 O . a a, k 7 u a, maa koa, aiom ad 0. VI 1 k -4kd a a, C -4 Ici a, d a, C O z a -4 c m C x k O 3 k O O c4 E rtl 9 (63a) Provided by IHSNot for ResaleNo reprod

30、uction or networking permitted without license from IHS-,-,-MIL-S-63326 (6) 9999906 1996622 251 M MIL-S-63326 (AR) AMENDMENT 6 PAGE 64 4.4.2.41, Safe & Arm Assembly (Prior to Assembling Borerider Shear Pin and Lock Plate): Critical category: Critical 1: Delete “J./“ in its entirety. Major category:

31、Major 102: Delete “.missing . 0.40% . 3.2 . Visual/ Manual“ and substitute “.missing I/ . 100% . 3.2 Vi sua 1 /Manual I . Notes: Add the following note: “L/ Major 102 shall be performed prior to critical 2Ii. PAGE 65 4.4.2.42, Safe & Arm Assembly: Major 103: Delete “100%“ and substitute “O .40%“. PA

32、GE 66 4.4.2.43, Safe & Arm Assembly (Prior to Assembling Shield and Lock Plate). Critical category: Delete “none defined“ and add new Critical defect as follows: “1 - Ball lock missing . . .loo% . . .3.2 . . .Gage“. Major 104: Delete “O .40%“ and substitute “100%“. PAGE 67 4.4.2.44, Critical 1: Dele

33、te “Eyelet ground open circuit, detonator .“ and substitute “Ground circuit open, detonator . II. PAGE 68 4.4.2.45, Critical 1: Delete “Selet ground open circuit, detonators .“ and substitute “Ground circuit open, detonators. . . I. 10 Provided by IHSNot for ResaleNo reproduction or networking permi

34、tted without license from IHS-,-,-MIL-S-63326 (AR) AMENDMENT 6 PAGE 69 4.4.2.46, Safe and Arm Assembly: LAT of S&A ASSEMBLIES, NO. OF SAMPLE UNITS column: Delete ii*ii. Transportation vibration, INSPECTION METHOD column: Delete “4.5.15.3“ and substitute “4.5.11.3“. Continuity - Resistance checks, RE

35、QUIREMENT column: Delete “3 -8“ and substitute “3.2“. Arming, INSPECTION METHOD column: Delete “4.5.17“ and substitute “4.5.13“. Main charge functioning: Add “2/“ after “functioning“. SAMPLE SIZE column: Add “l/“ after “SIZE“. +700 + 5OF column: Delete “+70 + 5F“ and substitute “AMBIENT“. PAGE 70 4.

36、4.2.47, Safe & Arm Assembly: LAT of S&A ASSEMBLIES, NO. OF SAMPLE UNITS column: II * II Transportation vibration, INSPECTION METHOD column: “4.5.15.3“ and substitute “4.5.11.3“. Continuity - Resistance checks, REQUIREMENT column: “3.8“ and substitute “3 -2“. Delete Delete Delete Main charge function

37、ing: Add “2/“ after “functioning“. SAMPLE SIZE column: Add IlJ after “SIZE“. +70 + 5OF column: Delete “+70 + 5OF“ and substitute “AMBIENT“. MDF functioning: Delete “4.5.14“ and substitute “4.5.14.1“. Delay detonator, delay time: Delete “4.5.14“ and substitute I 4 .5 .14 .2 II . Main charge functioni

38、ng: Delete “4.5.14“ and substitute “4.5.14 -2“. 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-b332b (b) W 0b Lbb2V O24 W MIL-S-63326 (AR) AMENDMENT 6 PAGE 73 4.5.9: Delete “Assemblies subjected to this test shall not be returned to the lot

39、.“ PAGE 74 4.5.14.2: Main charge lead explosive train functioning: Delete “ . The witness ring shall be 1-3/16 in I.D. x 1-1/2 in long x 3 in. O.D., cold drawn .“ and substitute “.The witness ring shall be 1 3/16 in I.D. x 3/4 in. long minimum x 2 1/2 in O.D. minimum, cold drawn. . . I. PAGE 75 4.5.

40、18: Delete “4.5.18“ and substitute “4.5.17“. PAGE 76 5.1 Preservation, Dac kaaina and markinq: * Delete “.in accordance with drawing 9329606“ and substitute “.in accordance with drawing 9329606 or alternate packing drawing 12937990“. * 5.2 Packina and markinq: Delete “.in accordance with drawing 932

41、9607“ and substitute “.in accordance with drawing 9329607 or alternate packing drawing 12937990“. The margins of this amendment are marked with an asterisk or vertical lines to indicate where changes (additions, modifica- tions, corrections, deletions) from the previous amendment were made. assumes

42、no liability whatsoever for any inaccuracies in this notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irre- spective of the marginal notations and relationship to the last previous amendment. This was done as a convenience only and the Government Custodian: Army-AR Preparing activity: Army-AR (Project 1345-0011) 12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-