ARMY MIL-H-44265 A-1990 HOOD COMBAT VEHICLE CREWMEN'S (BALACLAVA)《战斗用车辆炮手防护帽(巴拉克拉法帽)》.pdf

《ARMY MIL-H-44265 A-1990 HOOD COMBAT VEHICLE CREWMEN'S (BALACLAVA)《战斗用车辆炮手防护帽(巴拉克拉法帽)》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-H-44265 A-1990 HOOD COMBAT VEHICLE CREWMEN'S (BALACLAVA)《战斗用车辆炮手防护帽(巴拉克拉法帽)》.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、, MIL-H-44265A 4 997990b 03bb7b2 T i 5 - T MIL-H-44265A SUPERSEDING MIL-H-44265 22 December 1986 5 February 1990 MILITARY SPECIFICATION HOOD, COMBAT VEHICLE CREWMENS (BALACLAVA) This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. T

2、his specification covers one type and size of balaclava combat vehicle, crewmens hood made of fire-resistant materials. 2. APPLICABLE DOCUMENTS 2.1 Government documents, 2.1.1 Specifications, standards, and handbooks. The following specifi- cations, standards, and handbooks form a part of this docum

3、ent to the extent specified herein, Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplementthereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A-50083 - Bag,

4、Plastic, Folded Garment (General Use) DDD-L-20 - Label: For Clothing, Equipage, and Tentage PPP-B-636 - Boxes, Shipping, Fiberboard Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: U.S. Army Nati

5、ck Research, Development, and Engineering Center Natick, MA 01760-5014 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. msc N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is

6、unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI L-H- 4 4 26 5 A MIL I TARY MIL-C-3735 - Cuffs, Knit, Wrist and Ankle, and Cloth, Knitted MIL-L-35078 - Loads, Unit: Preparation of Semiperishable Subsistence Items; Clothing, Personal Equi

7、pment and Equipage; General Specification For MIL-C-43303 - Cord, Elastic Cotton MIL-T-43636 - Thread, Aramid MIL-W-43685 - Webbing, Tape, Textile, Aramid Fiber MIL-C-44236 - Cloth, Knitted, Aramid, Bi-Ply MIL-C-44263 - Cloth, Laminated, Waterproof, Moisture Vapor Permeable and Flame Resistant (Wt.

8、3.4 oz) STANDARDS FEDERAL FED-STD-751 - Stitches, Seams, and Stitchings MIL I TARY MIL-STD-105 - Sampling Procedures and Tables for Inspection MIL-STD-129 - Marking for Shipment and Storage MIL-STD-147 - Palletized Unit Loads MIL-STD-731 - Quality of Wood Members for Containers and Pallets . by Attr

9、ibutes (Unless otherwise indicated, copies of federal agd military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following documents form a part of

10、 this Unless otherwise specified, the issues document to the extent specified herein, of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the docum

11、ents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 3951 - Standard Practice for Commercial Packaging (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) 2 Provided by

12、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3 * L flIL-H-q42b5A flV 9999906 03bb7bY 3 = _ - - MIL-H-44265A THE COLOR ASSOCIATION OF THE UNITED STATES Standard Color Card o America Department of Defense Standard Color Card for Sewing Threads (Color cards may

13、 be available from the Color Association of the United States, 343 Lexington Avenue, New York, NY 10016-0927. If color cards are not available from the Color Association, individual color samples may be obtained from the contracting activity or as directed by the contracting activity.) (Non-Governme

14、nt standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services. 2.3 Order of precedence. In the event of a conflict between the text of th docume

15、nt and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. S 3. REQUIREMENTS 3.1 First article. When specified (see 6.21, a sample shall be subjected to f

16、irst article inspection (see 6.3) in accordance with 4.3. 3.2 Guide sample. Guide samples, when furnished, are solely for guidance and information to the contractor (see 6.4). appear in the sample, in which case this specification shall goyern. Variation from this specification may 3.3 Materials, It

17、 is encouraged that recycled material be used when h practical as long as it meets the requirements of this speclfication, 3.3.1 Cloth, knit, aramid. The outer shell of the hood (cover fabric) shall be knit, aramid, Olive Green 106 cloth conforming to type IV, class 3 of I MIL-C-3735. 3.3.2 Cloth, k

18、nitted, aramid, bi-ply, The bib, the lining (layer next to head), and the center strip insert and side vent insert of the interlining shall be bi-ply aramid, Olive Green 106 cloth conforming to MIL-C-44236. 3.3.3 Cloth, laminated, waterproof, moisture vapor permeable and flame resistant. The interli

19、ning (middle layer) of the hood shall be a natural color and conform to MIL-C-44263. 3.3.4 Elastic cord. The elastic cord for the face opening shall conform to class 2 of MIL-C-43303. The color shall be Olive Drab 7. Y 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without li

20、cense from IHS-,-,-MIL-H-44265A 3.3.5 Webbing, aramid. The aramid webbing for the pull tab shall conform to type II of MIL-W-43685, except for Test Method 5660, the test specimen shall be exposed for 6 standard fading hours and at the end of each 3 hour exposure period, a new piece of calibration pa

21、per shall be placed ir. the machine. The color shall be Olive Green 106. 3.3.6 Thread, aramid. The aramid thread shall conform to size B of MIL-T-43636. The color shall be Olive Drab S-1, C.A. 66022. 3.3.7 Label. The label shall conform to type VI, class 14 of DDD-L-20. Fastness to laundering requir

22、ements of DDD-L-20 shall apply. The label shall cuntain the following information in capital letters: HOOD, COMBAT VEHICLE CREWMENS (BALACLAVA) WASHING INSTRUCTIONS: LAUNDER IN ACCORDANCE WITH NATICK FORMULA I. DO NOT TUMBLE DRY OR WRING/TWIST. HAND WASH IN WARM WATER USING MILD DETERGENT, RINSE IN

23、CLEAR WARM WATER AND HANG TO DRIP DRY AT ROOM TEMPERATURE. DO NOT DRY CLEAN. The contractor shall insert the Date of Manufacture with indelible ink, 3.4 Design. The hood shall be the pull-over-the-head type with attached bib. The hood shall have a facial opening which may be adjusted by means of a p

24、ull 3,5 Figure 1, Figure 1 is furnished for information only. If there are any inconsistencies between the written Specification and the figure, the written specification shall control. 3.6 Patterns, Standard patterns, which provide an allowance for all seams, will be furnished by the Government and

25、 shall be used by the contractor as a guide for cutting working patterns only, The standard patterns shall not be altered in any way (except as indicated in 3.*7.2) and the working patterns shall be cut to conform exactly to the standard patterns. 4 Provided by IHSNot for ResaleNo reproduction or ne

26、tworking permitted without license from IHS-,-,-MIL-H-44265A 3.6.1 Pattern parts. The pattern parts, cutting quantities, and materials for the parts shall be as specified below: Components for outer cover Mater ia1 - Item Nomenclature of part Parts per hood Cloth, knit, aramid 1 Side cover 2 1 1 2 C

27、enter top cover 3 Center neck cover Components for 1 ining - I tem Nomenclature of part Parts per hood Mat er i a 1 C lo th, knitted y 1 Side lining aramid, bi-ply 2 Center top lining 3 Center neck lining Components for interlining Ma ter ia 1 - I tem Nomenclature of part Cloth, laminated, 1 Side in

28、terlining waterproof , moisture vapor permeable and 8 flame resistant t 2 Cloth y knitted , 3 aramid , bi-ply 4 Center interlining Side vent insert Center strip insert 2 1 1 Parts per hood 2 2 2 1 Components for bib - Item Nomenclature of part Parts per hood Ma ter ia1 Cloth , knitted y 1 Front bib

29、aramid, bi-ply 2 Back bib 3.7 Construction. The construction shall conform to the requirements specified in table I and herein. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-HIL-H-442b5A 8LJ 77777Ob 3bb7b7 q MIL-H-44265A 3.7.1 Stitches, seams, an

30、d stitching. All stitches, seams, and stitching shall conform to FED-STD-751. The type of seam, stitching, and stitches per inch shall be as specified in table I. seams sewn so that no raw edges, run-Offs, twists, pleats, puckers, or open seams occur. All seams shall start and end evenly. Thread ten

31、sion shall be maintained so that there is no tight or loose stitching. Seam allowances shall be maintained with 3.7.1.1 Type 301 stitching. Ends of all stitching shall be backstitched or overstitched 1/2 inch minimum except when caught in other stitching or turned under in a hem, Thread tension shal

32、l be maintained so that there will be no loose stitching resulting in loose bobbin or top thread, or excessively tight stitching resulting in puckering of the materials sewn. embedded in the materials sewn. The lock shall be t 3.7.1.1.1 Repairs of type 301 stitching. Repairs of type 301 stitching sh

33、all % be as follows: a. When thread breaks or bobbin run-outs occur during sewing, the stitching shall be repaired by restarting the stitching a minimum of 1 inch back of the end of the stitching. A/ noted during inspection of the item (in-process or end item) shall be repaired by overstitching. The

34、 stitching shall start a minimum of 1 inch in back of the defective area and continue a minimum of 1 inch beyond the defective area on to the existing stitching. Loose or excessively tight stitching shall be repaired by removing the defective stitching, without damaging the materials, and restitchin

35、g in the required manner. L/ - l/ When making the above repairs, the ends of the stitching are not required to be backstitched. bo Thread breaks or two or more consecutive skipped or run-off stitches 8 3.7.1.2 Type 401 stitching. Thread tension shall be maintained so that there will be no loose stit

36、ching. 401 stitch type, when not turned under in a hem or held down by other stitching, shall have a 1/2 to 3/4 inch chain extending beyond each end. The looper (under thread) shall be hidden between the cover and lining assembly. shall be in accordance with 3.7.1.1.la and 3.7.1.1.lb. using 301 stit

37、ch type. Both ends of all seams or stitching produced with All repairs Repairs may be made 3,7.1.3 Types 502, 503, 504, 515, 516, and 519 stitching. Thread tension shall be maintained so that there will be no loose stitching. All repairs shall be in accordance with 3.7.1.1.la and 3.7.1.1.lb except s

38、ubstitute 3/4 inch for 1 inch wherever 1 inch appears. 6 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-44265A 3.7.2 Use of automated apparel equipment. Automated apparel equipment may be used to perform any of the operations specified in ta

39、ble I, providing that the seam and stitch type are as specified and the finished component conforms to the required configuration. forwarded, the component shall conform to that pattern. When a government furnished shaper pattern is 3.7.3 Stitches per inch, The minimum and maximum number of stitches

40、 per inch shall be as specified in table I, 3.8 Manufacturing operation requirements. The hood shall be manufactured in The contractor is accordance with operation requirements specified in table I. not required to follow the exact sequence of operations. Any additional basting or holding stitching

41、used to facilitate manufacture is permissible, provided the thread is removed or does not show on the finished hood (see 6.5). i 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-qq2b5A1q 7797706 036b767 2 MIL-H-44265A V O O 5: c1 3 U WLiO o al

42、n v) U c e, O n Eo r o -4 c, U e, W o) -U W O Cr e e, U id -I e, E n 4 N a 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* NIL-H-V4265A 44 m 7797906 0366770 7 W MIL-H-44265A 7 U W O v ze z? I mo ,fsJ O0 c? a I L I iI r*l I I tu I; tT) k2 v) Lal G

43、 c, o,c vu 32 h 3 u C O 0 - W v) 42 C o, C O 4 u V 9) w o, U W O 4J I C al 4 i ci: Li v) o cmw c (do lus $2. cil E m.4 . an u lu d c; cr) e v) 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI L-H-44 26 5 A wel ril i ril r( O0 O O O O viv) U U U U

44、 I SI uw Av, ow d d a I- 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-E-44265A N I W a, -i 2 r4 ril I 4 C U 4 O mu O0 mm L O O0 mu 4-i al I 5 h U - 5 - O u W 4 al O (d 4 5 (d c, c, (d U C (d bt C .-I C .4 -i al 24 I 03 U4-l OE o(d ala al VL

45、 id bo1 alCC, ec a, .4 a, wci O O U al VI L . I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- tIIL-H-2bS di.I m 7779706 0366777 1 m MIL-H-44265A a a I I A 84 B v) u) (d bn E *-I c -I 84 3 2 C *-I c .4 ri( L al c, E -I L g 3 O c, an -I a n- u cc br

46、l Q o0 -U a 1 W c oc CI c, 4 0x4 VC soCd EX 0)w a.4 (071 o - M-Q, v) x ESC u) Q, v) O *2 O cr4 I- - o 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-H-44265AIOb 0366778 3 c O r. i -0 MI L-H-4426 5A 3.9 Finished measurements. The hood shall co

47、nform to the measurements specified in table II. TABLE II. Finished measurements (inches) Area to be Measurement To ler an ce me as ur ed Length L/ Width - 21 24 9 +1 - - + 3/4 Face opening - 3/ 9-1/2 - + 1/2 - l/ Place hood face side up on a flat surface, align bottom edges of front and back of bib

48、 and butt top and bottom edges of face opening. this position measure length in a straight line from folded edge of crown at highest point to bottom of hood at lowest point on bib. With hood in - 21 With hood positioned as indicated in footnote I/, measure across the hood in a straight line from fol

49、ded edge to folded edge. The line of measurement shall be perpendicular to the length measurement and 1/2 to 1 inch below the tuck. Fold hood in half lengthwise so fold runs in the length direction of the center top cover and center neck cover. Place folded hood on flat surface with edges of face op