ARMY MIL-C-51098 E (7)-1991 CYLINDER NITROGEN-FILLED PUNCTURABLE SEAL《可穿孔的密封充氮子弹夹》.pdf

《ARMY MIL-C-51098 E (7)-1991 CYLINDER NITROGEN-FILLED PUNCTURABLE SEAL《可穿孔的密封充氮子弹夹》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-51098 E (7)-1991 CYLINDER NITROGEN-FILLED PUNCTURABLE SEAL《可穿孔的密封充氮子弹夹》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、- MIL-C-51098E (7) 42 9999906 0489828 4 MIL-C-51098E( EA) AMENDMENT 7 9 August 1991 SUPERSEDING AMENDMENT 6 5 March 1990 MILITARY SPECIFICATION CYLINDER, NITROGEN-FILLED, PUNCTURABLE SEAL This amendment forms a part of MIL-C-S1098E(EA), dated I2 February 1981, and is approved for use by the U.S. Arm

2、y Chemical Research, Development and Engineering Center, Depart- ment of the Army and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 2.1: Under “SPECIFICATIONS”, delete the following: “QQ-S-781 PPP-B-5 66 PPP-B-5 85 PPP-B-62 1 PPP-B-636 PPP-B-676 PPP-C-84 3

3、 MILITARY MIL-B-117 AMSC NIA DISTRTBUTION STATEMENT A. * Strapping, Steel, Flat and Seals. Boxes, Folding, Paperboard. Boxes, Wood, Wirebound. Boxes, Wood, Nailed and Lock-Corner. Boxes, Shipping, Fiberboard. Boxes, Setup. Cushioning, Material, Cellulosic. . Bag and Sleeve, Interior Packaging.” FSC

4、4230 Approved for public release; distribution is unlimited. 1 of 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-!MIL-C-SLOS8E (7) 42 979990b 0489827 b W MIL-C-5 1098E(EA) AMENDMENT 7 PAGE 2 2.1: Under “STANDARDS”, “MILITARY”: Delete “MIL-STD-129

5、- Marking for Shipment and Storage” and substitute “MIL-STD-171 - Finishing of Metal and Wood Surfaces.” Under “DRAWINGS” add “5-51-557 - Protective Finish.” After the list of drawings add the following: “QUfi ASSURANCE PROVISIONS (QAP) 702- 1-2 - Chemical Agent Resistant Coating (CARC) System for D

6、econtamination Items. SPECIAL PACKAGING INSTRUCTIONS (SPI) P5-5 1-376 - Cylinder, Nitrogen Filled, Puncturable Seal.” 3.1.2.1: Add the following new paragraph: “3.1.2.1 Protective finish. The cylinder protective finish shall conform to Drawing 5-51-557 or Finish No. 1.1.2.2 of MIL-STD-171.” PAGE 4 4

7、.3.3.1 (b), line 2: Delete “(4.4.3.3)” and substitute “(4.4.3.4)”. 4.4.1, Delete in its entirety and substitute the following: “4.4.1 Lotting. Each lot shall be identified and controlled in accordance with MIL- STD-1168. A lot of cylinders shall consist of the filled cylinders produced by a manufac-

8、 turer at one plant and under essentially the same manufacturing conditions. No more than one interfix of the following components shall be contained in any one lot of cylinders produced: a. Body b. Cap” 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

9、,-,-MIL-C-51098E(EA) AMENDMENT 7 PAGE 5 4.4.3.3 (a) : Under “Major” defects of AQL 1.0 percent add the following: “111 Spherical radius incorrect 112 Protective finish missing” Under “Minor” defects delete the following: “201 Protective finish missing or incorrect” Renumber as 4.4.3.4(a) and add the

10、 following new paragraph: “4.4.3.3 Protective finish. Inspection for conformance to Chemical Agent Resis- tant Coating (CARC) requirements shall be in accordance with QAP 702-1-2.” PAGE 6 I 4.4.3.3 (b): Renumber as “4.4.3.4 (b)” 4.4.4.2, Sentence 1: Delete in its entirety and substitute the followin

11、g: * “Submerge the filled cylinder in boiling water or air heated to 100” f 5C for at least 15 minutes.” 4.4.4.3, Delete in its entirety and substitute the following: “4.4.4.3 Rupture. The filled cylinder shall be tested in a heating device that provides an environment that is homogeneous within 25F

12、 during the test period. The temperature of the environment shall be raised from a temperature not to exceed 150F at a rate not to exceed 300F per minute until cylinder rupture occurs. Examine the cylinder for confor- mance to 3.3.2 (see 6.3) PAGES 7 AND 8 Delete section 5 in its entirety and substi

13、tute the following: “ 5. PACKAGING 5.1 Packaging. Packaging requirements shall be as specified on SPI P5-51-376.” 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-i=- I MIL-C-5109E (7) 42 - 9999906 0489831 4 = MIL-C-5 1098E(EA) AMENDMENT 7 6.2 (b):

14、Delete in its entirety and substitute the following: “Level of packing required.” PAGE 9 6.3, Sentence 1: Delete “hot air oven” and substitute “heating device”. , Custodian: Preparing activity: Army - EA Army - EA Project No. 4230-AO93 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-