ARMY MIL-C-14633 D-1994 CASES DECORATION PRESENTATION《礼物用装饰箱》.pdf

《ARMY MIL-C-14633 D-1994 CASES DECORATION PRESENTATION《礼物用装饰箱》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-C-14633 D-1994 CASES DECORATION PRESENTATION《礼物用装饰箱》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、NOT MEASUREMENT SENSITIVEJ MIL-C-14633D 21 December 1994 SUPERSEDING MIL-C-14633C 5 February 1992 MILITARY SPECIFICATION CASES, DECORATION, PRESENTATION This specification is approved for use by all Departments and agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers

2、presentation cases for decorations awarded within the Department of Defense. 1.2 Classification. Cases covered by this specification shall be of the following types and classes (see 6.4). Type 1 - Medal of Honor Class 1 - U.S. Military Personnel Class 1A - U.S. Military Personnel (with extra tabs) T

3、ype II - Distinguished Service Cross Class 1 - U.S. Army Personnel Class 1A - U.S. Army Personnel (with extra tabs) Class 2 - Civilian distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-14633D W 999990b 1995769 286 m MIL

4、-C-14633D *4 . Class 2A - U.S. Military, Civilian Type VI, Class 1 and 1A pads; Type VIIS Class 1 and 1A pads and Type XVII pads. Pads shall be fabricated in accordance with Drawing 4-4-85A (Figure 2) and 4-4-93 (Figure 3), as applicable. The pads shall consists of a 118 inch (0.32 cm) thick vinyl i

5、mpregnated urethane pad overlaid with 0.012 inch (0.030 cm) gray omni flocked vinyl and laminated to a piece of 0.020 inch (0.050 cm) thick rigid white vinyl. The flocked overlay shall be in two pieces with both pieces heat sealed to the rigid vinyl. The lower section of the pad shall contain a pock

6、et for each medal required. The lift tab shall be an integral part of the pad. 3.3.3.3 TyDe XVII Dads. Pads shall be fabricated from 14-ply bristol board and shall conform to the details and dimensions of Drawing 4-4-100 (Figure 6). The face, edge and a minimum of 318 inch (0.95 cm) on all sides of

7、the back of the pad shall be covered with white plush. After the applicable attachments have been securely anchored, the reverse side of the pad shall be covered with chipboard specified in 3.2.3. 3.3.4 Type XVI case. The Type XVI case shal- be molded from polystyrene specified in 3.3.10 in accordan

8、ce with Drawing 4-4-99 (Figure 4). The walls for both upper and lower sections shall have a typical thickness of 0.070 inch (0.177 cm). The exterior surface shall have a morocco textured finish. The top surfaces of the filigree bar, the words UNITED STATES OF AMERICA and the exterior of the cover sh

9、all be hot leaf stamped in silk vinyl or imitation gold. The hinge shall be covered with white satin cloth glued to the upper and lower lids. 3.3.4.1 Interior lid. The interior lid shall have a white satin cloth or brushed white silk vinyl covered die-cut chipboard form 3-5/8 inches (9.21 cm) in len

10、gth by 4 inches (10.16 cm) in width securely place in the plastic shell. The chipboard form shall have line-cuts on the reverse side 7/16 inch (1.11 cm) from each outside edge with each corner notched with a 45 degree cut. The face and walls of the form shall be covered with sufficient white satin c

11、loth or brushed white silk vinyl to create a pillowy effect when the lid is positioned at a 45 degree angle. The lower lid shall be unlined. 3.3.4.2 Pads. The pads shall be fabricated as specified in Drawing 4-4-99A (Figure 5). The pad shall consist of a 118 inch (0.32 cm) thick vinyl impregnated 7

12、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-L4633D - 9999906 1995775 58T = MIL-C-14633D urethane pad overlaid with 0.012 inch (0.030 cm) cadet gray omni flocked vinyl and laminated to a piece of 0.020 inch (0.050 cm) thick rigid white vinyl

13、. The flocked overlay shall be two pieces with both pieces heat sealed to the rigid vinyl. The lower 1-1/2 inch (3.81 cm) section shall contain a pocket to place the medal in during shipment. The lift tab is an integral part of the pad. 3.3.4.3 Markinq. The manufacturer shall mold his name in the in

14、terior bottom of the case. The letters shall be raised and be clearly readable once the interior pad is lifted. 3.4 Workmanship. Cases shall be clean, well made and shall meet the acceptable quality levels established by this specification. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibilitv for insp

15、ection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein Except as otherwise specified in the contract or purchase order, the contractor may use his own or any o

16、ther facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and s

17、ervices conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items shall meet all requirements of sections 3 and 5. The inspections set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspecti

18、on requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling inspection as part of manufacturing operations is an acceptable prac

19、tice to ascertain conformance to requirements; however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.2 First article inspection. When a first article is required, inspection testing shall

20、 be made on a completely finished case for all provisions of this specification applicable to the end product examination and tests (see 6.5). 4.3 Samplinq for inspection and acceptance. Sampling for inspection and acceptance shall be in accordance with the provisions set forth in MIL-STD-105, excep

21、t where otherwise indicated. 4.3.1 Certification of compliance. Components listed below may be accepted on the basis of a contractors certification of compliance for the requirements specified in applicable paragraphs of this specification. 8 Provided by IHSNot for ResaleNo reproduction or networkin

22、g permitted without license from IHS-,-,- Component Cord, elastic Chipboard Attachment loop wire Vinyl material Mylar leaf Polystyrene Lacquer Polyurethane pad Molded insert Lift tab Pad Tabs _ - MIL-C-14b33D = Ob 1995776 4Lb MIL-C-14633D TABLE I. CERTIFICATION OF COMPLIANCE. Characteristics Materia

23、l identification, diameter and color Material identification and weight, finish and thickness Material identification and karat of plating Material identification, thickness, minus 10 degrees F cold crack resistance, grain retention, color Material identification Material identification and color Ma

24、terial identification Material identification and thickness Material identification, thickness and facing Material identification Material identification and plies Material identification and thickness Rum t para 3.2.2 3.2.3. and 3.3.4.1 3.2.6 3.2.7.1 and 3.2.7.2 3.2.8 3.2.10 3.2.11 3.3.1.1 and 3.3.

25、1.2 3.3.2 3.3.3.1 3.3.3.1 thru 3.3.3.3 3.3.3.1 4.3.2 Process examination. Examination shall be made during the manufacturing process for the requirements listed below to establish that no deviation is made from indicated requirements. Whenever a nonconformance is noted, correction shall be made to a

26、ffected items and the process. Reauirements or operation Polyurethane pad is glued to the exterior top of the lid shell Die-cut cardboard form securely glued to metal shell interior of the lid section Rmt para 3.4 3.3.4.1 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without

27、 license from IHS-,-,- MIL-C-14b33D 0b 1775777 352 MIL-C-14633D Wire loops, metal tab attachments, lift tabs and elastic cords securely anchored to reverse side of pad. Sides and back of pad are covered with a minimum of 3/8 inch (0.95 cm) of gray plush or flocking 3.3.3.1 3.3.3.1 4.3.3 Inspection o

28、f the end item. 4.3.3.1 Visual examination of case. Examination shall be made at a distance of 16 to 22 inches (40.64 cm to 55.88 cm) under normal daylight or its equivalent. The defects found during examination shall be classified in accordance with 4.3.3.1.1 and 4.3.3.1.2. The unit of product for

29、these examinations shall be one completely fabricated case. Zxamine Exterior surf ace t nter ior surfaces Jorkmanship TABLE II. DEFECTS. classification Defect Color and finish does not match the standard or approved sample Not covered as specified . Pattern or lettering missing . Not correct pattern

30、 or lettering Lettering incorrect size or position . Covering not taut, i.e., any wrinkle(s), bubble(s), or crease Visible imperfection in cover, i.e., spotted or stained, cut, torn, abraded or otherwise damaged . of voids or skips, not well defined . Pattern or lettering not clear or not free Plush

31、, flocking or satin does not match the standard or approved sample for color, finish or texture . Visible imperfection in plush, or flocking, elastic cord or satin, i.e., stained, discolored, cut, torn, frayed or otherwise damaged . Elastic cord not correct color . Satin cloth does not have pinked o

32、r fused sides . Hinge not as specified . bottom of the case Lid (when closed) is not aligned with the Case is punctured, malformed, broken, Major (*) Minor 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-14633D 9999906 1995778 299 MIL-C-146

33、33D TABLE II. DEFECTS (Continued) Classification 3xamine darking Defect indented or otherwise damaged . Lid does not close completely over Lid does not spring closed when released components from a 30 degree angle indented or otherwise damaged . Metal edge contains sharp edge, burr or is Hinge not c

34、overed on the inside with satin Lid recess for dust shield not at 45 degree Attachment(s), lift tab(s), wire loop(s) or Ends of striking edge not butted flush with The face and walls of the interior lid does Incorrect pad or no pad dented, bent or otherwise damaged . cloth . angle . cord not securel

35、y anchored ends of the hinge . not have a pillowy effect . Pad not covered as specified . Molded insert missing Molded insert not securely glued to shell One or more die-cut areas missing from pad . Die-cut area(s) not proper size or not in the proper location . Marking not placed as required . Miss

36、ing, illegible or incorrect Major (*) Minor 4.3.3.1.1 Examination for defects in finish. desiqn, material, construction, workmanship and markinq. Defects designated by an asterisk (*) shall be classified as major when seriously affecting appearance or serviceability and minor when affecting appearan

37、ce or serviceability but not seriously. 4.3.3.1.2 Examination of cases for defects in dimensions. Any dimension that is not within the specified tolerance shall be classified as a defect. 4.3.3.1.3 Examination of preparation for delivery requirements. An examination shall be made to determine that p

38、ackaging, packing and marking requirements are complied with. Defects shall be scored in accordance with the list below. The sample unit shall be one shipping container fully prepared for delivery, with the exception that it need not be sealed. Defects of closure listed below shall be examined on a

39、shipping container fully prepared for delivery. The lot size shall be the number of containers in the end item inspection lot. 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EXAMINE Markings, exterior and Interior Materials Workmanship Content We

40、ight DEFECT Missing, incorrect, illegible or improper size, and location sequence or method of application. Component missing, damaged or otherwise defective, affecting serviceability. Inadequate application of components, such as incomplete closure of container flaps, inadequate stapling. Bulging o

41、r distortion of containers. Number in container is more or less than required. Net weight exceeds the requirements. 5. PREPARATION FOR DELIVERY 5.1 Preservation. Preservation shall be level A or commercial, as specified (see 6.2). 5.1.1 Level A. A polyurethane pad, 3 inches (7.62 cm) square by 1 inc

42、h (2.54 cm) thick, shall be placed in each case and the case closed. A one inch (2.54 cm) wide snug-fitting paperboard sleeve shall be fitted over the closed case and the case shall be packaged in a snug-fitted Set-up paperboard box conforming to Type I, Variety 1, Class A, Style 4 of PPP-B-676. Box

43、 closure shall be in accordance with the appendix of the container specification. 5.1.2 Commercial. Cases shall be preserved and packaged in accordance with the applicable requirements of ASTM-D-3951. 5.2. Packinq. Packing shall be level A, B or commercial as specified (see 6.2). 5.2.1 Level A. Case

44、s of one type only packaged as specified in 5.1 shall be packed in a snug-fitting fiberboard shipping container conforming to Class Weather Resistant, Type V3c or V3s of PPP-B-636. Closure and reinforcement shall be in accordance with the appendix of the applicable specification. 5.2.2 Level B. Case

45、s of one type only packaged as specified in 5.1 shall be packed in a snug-fitting fiberboard shipping container conforming to Class Domestic, Grade 275 of PPP-B-636. Closure shall be in accordance with the appendix of the container specification. 5.2.3 Commercial. Cases packaged as specified in 5.1

46、shall be packed in accordance with the applicable requirements of ASTM-D-3951. 5.3 Markinq. In addition to any special marking required by the contract or purchase order (see 6.2), unit packages and shipping containers shall be marked in accordance with MIL-STD-129 or ASTM-D-3951 as applicable. 12 P

47、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6. NOTES MIL-C-lY633D W 999990b 1995780 947 MIL-C-14633D (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. Cases covered

48、by this specification are intended to be used as presentation cases for decorations awarded by the U.S. Government. 6.2 Acaiisition requirements. Acquisition documents must specify the following: a. Title, number and date of this specification. b. Issue of DODISS to be cited in the solicitation, and

49、 if required, the specific issue of individual documents referenced (See 2.1) the c. When first article is required. (See 3.1). d. Selection of application levels of packaging and packing (See 5.1 and 5.2). e. When special marking is required (See 5.3) 6.3 Class 1A and Class 2A Pads. The class 1A and the class 2A pads were developed to accept button back lapel buttons and service ribbons with a pin and catch type attach