ARMY A-A-59354-2000 HYDRAULIC FLUIDS PETROLEUM BASE FOR MACHINE TOOLS [Superseded ARMY MIL-H-46001 D CANC NOTICE 1 ARMY MIL-H-46001 D ARMY MIL-H-46001 C (2) ARMY MIL-H-46001 C (1) .pdf

《ARMY A-A-59354-2000 HYDRAULIC FLUIDS PETROLEUM BASE FOR MACHINE TOOLS [Superseded ARMY MIL-H-46001 D CANC NOTICE 1 ARMY MIL-H-46001 D ARMY MIL-H-46001 C (2) ARMY MIL-H-46001 C (1) .pdf》由会员分享，可在线阅读，更多相关《ARMY A-A-59354-2000 HYDRAULIC FLUIDS PETROLEUM BASE FOR MACHINE TOOLS [Superseded ARMY MIL-H-46001 D CANC NOTICE 1 ARMY MIL-H-46001 D ARMY MIL-H-46001 C (2) ARMY MIL-H-46001 C (1) .pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、METRICA-A-59354April 6, 2000SUPERSEDINGMIL-H-46001D7 December 1989COMMERCIAL ITEM DESCRIPTIONHYDRAULIC FLUIDS, PETROLEUM BASE, FOR MACHINE TOOLSThe General Services Administration has authorized the use of this commercial itemdescription, for all federal agencies.1. SCOPE. This specification covers

2、four grades of petroleum-based hydraulic fluids, hereafterreferred to as “fluid”. This product is intended for use in hydraulic systems of metalworkingmachine tools that require anti-wear oils.2 CLASSIFICATION.2.1 Grades . The fluid shall conform to the following viscosity grades:Grade 1 ISO VG 32Gr

3、ade 2 ISO VG 46Grade 3 ISO VG 68Grade 4 ISO VG 1503. SALIENT CHARACTERISTICS3.1 Materials . The fluids shall be derived from petroleum fractions, but may contain additives tomeet all of the salient characteristics.Beneficial comments, recommendations, additions, deletions, clarifications, etc. and a

4、ny otherdata which may improve this document should be sent by letter to : U.S. Army Tank-automotiveand Armaments Command, ATTN: AMSTA-TR-E/IE, Warren, MI 48397-5000.ASMC N/A FSC 9150DISTRIBUTION STATEMENT A . Approved for public release, distribution is unlimited.Provided by IHSNot for ResaleNo rep

5、roduction or networking permitted without license from IHS-,-,-A-A-5935423.2 Viscosity . The fluid shall have a viscosity at 40 degrees Celsius (C) as follows when testedin accordance with (IAW) ASTM D 445:Grade 1 between 28.8 and 35.2 square millimeter per second (mm 2 /s)Grade 2 between 41.4 and 5

6、0.6 mm 2 /sGrade 3 between 61.2 and 74.8 mm 2 /sGrade 4 between 135 and 165 mm 2 /sThe fluid viscosity index shall not be less than 90 when tested IAW ASTM D 2270.3.3 Low-temperature use . Fluid grades 1, 2, and 3 shall have a pour point not greater than-12C, and fluid grade 4 shall have a pour poin

7、t not greater than 6C when tested IAWASTM D 97.3.4 Fire safety . The fluid shall have flash and fire points not less than the following when testedIAW ASTM D 56.Grade 1 Grade 2 Grade 3 Grade 4Flash point (in C) 188 196 196 221Fire point (in C) 216 218 218 2463.5 Protection from hydraulic cavitation

8、. The fluid shall produce no greater than100 milliliters ( mL ) of foam after the 10-minute settling periods of both the first and second24C tests, and no greater than 25 mL of foam after the 10-minute settling period of the 93.5Ctest when tested IAW ASTM D 892.3.6 Wear protection .3.6.1 Pump wear t

9、est (Grades 1, 2 and 3 only) . The fluid shall have wear characteristics thatprovide a pump ring and vane weight loss of not greater than 50 milligrams (mg) when testedIAW ASTM D 28 82.3.6.2 Galvanic corrosion . The fluid shall pass Method 5322 of FED-STD-791.3.6.3 Rust prevention . The fluid shall

10、pass Procedure A of ASTM D 665.3.6.4 Neutralization number . Fluid grades 1, 2, and 3 shall have a weak acid neutralizationnumber not greater than 1.5 and fluid grade 4 shall have a weak acid neutralization number lessthan 0.2 when tested IAW ASTM D 664.3.7 Fluid quality . The fluid shall have an AS

11、TM color that conforms to the following limitswhen tested IAW ASTM D 1500:Grade 1 - not more than 2.0Grade 2 - not more than 3.0Grade 3 - not more than 3.0Grade 4 - not more than 5.0Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5935433.8 Toxici

12、ty . The fluid shall not present a health hazard when used as intended (see 1).Questions on toxicity shall be referred by the procuring activity to the appropriate departmentalmedical service.4. REGULATORY REQUIREMENTS. The offeror/contractor is encouraged to use recoveredmaterials to the maximum ex

13、tent practicable, in accordance with paragraph 23.403 of the FederalAcquisition Regulation (FAR).5. PRODUCT CONFORMANCE. The products provided shall meet the salient characteristicsof this CID, conform to the producers own drawings, specifications, standards, and qualityassurance practices, and be t

14、he same product offered for sale in the commercial marketplace.The Government reserves the right to require proof of such conformance (see 7.3).5.1 Market acceptance . The fluid offered shall be certified that it meets a machine toolmanufacturers quality requirements for use in its machine tools. A

15、machine tool manufacturer isone that has been producing machine tools for commercial sale for at least the last 5 consecutiveyears.6. PACKAGING. The innermost containers of this product shall have the specification number(A -A -59354) and grade clearly labeled (see 2.1 ). Additional preservation, ma

16、rking andpackaging shall be as specified in the contract or order (see 7.3).7. NOTES7.1 Part or Identification Number (PIN) . The following PIN procedure is for Governmentpurposes and does not constitute a requirement for the contractor. The PINs to be used forhydraulic fluids acquired to this CID a

17、re created as follows (see 7.3):AA59354 - XXDash number (see table II).Example: 01CID number.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-593544TABLE II. National stock numbers and dash numbers .Dash number Grade Container National stock numbe

18、r01 1 5 gallon can (CN) 9150-00-966-883002 1 55 gallon drum (DR) 9150-00-966-883103 2 55 gallon drum (DR) 9150-00-966-883304 2 5 gallon can (CN) 9150-00-966-883405 3 5 gallon can (CN) 9150-00-966-883206 3 55 gallon drum (DR) 9150-00-966-883507 4 5 gallon can (CN) 9150-00-966-883608 4 55 gallon drum

19、(DR) 9150-00-966-88377.2 Source of documents .7.2.1 The Code of Federal Regulations (CFR) may be obtained from the Superintendent ofDocuments, U.S. Government Printing Office, Washington, DC 20402 or at their Websitewww.access.gpo.gov/nara/cfr/cfr-table-search.html.7.2.2 FED-STD-791 “Lubricants, Liq

20、uid Fuels, and Related Products; Methods of Testing” maybe obtained from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D,Philadelphia, PA 19111-5094.7.2.3 ASTM D56 “Standard Test Method for Flash Point by Tag Closed Tester(DoD Adopted)”; A STM D97 “Standard Test Method for P

21、our Point of Petroleum Products(DoD Adopted)”; ASTM D445 “Standard Test Method for Kinematic Viscosity of Transparentand Opaque Liquids (the Calculation of Dynamic Viscosity) (DoD Adopted)”; ASTM D664“Standard Test Method for Acid Number of Petroleum Products by Potentiometric TitrationBritish Stand

22、ard 4457 (DoD Adopted)”; ASTM D665 “Standard Test Method forRust -Preventing Characteristics of Inhibited Mineral Oil in the Presence of Water(DoD Adopted)”; ASTM D892 “Sta ndard Test Method for Foaming Characteristics ofLubricating Oils (DoD Adopted)”; ASTM D1500 “Standard Test Method for ASTM Colo

23、r ofPetroleum Products (ASTM Color Scale) (DoD Adopted)”; ASTM D2270 “Standard Practice forCalculating Viscosity Index from Kinematic Viscosity at 40 and 100 Degrees C(DoD Adopted)”; and ASTM D2882 “Standard Test Method for Indicating the WearCharacteristics of Petroleum and Non-Petroleum Hydraulic

24、Fluids in a Constant Volume VanePump (DoD Adopted)” are available from the American Society for Testing and Materials,100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or at their Websitewww.astm.org.7.3 Ordering data . The contract or order should specify the following:a. CID document number,

25、 revision, and CID PIN (see 7.1).b. Product c onformance provisions (see 5).c. Packaging requirements (see 6).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5935457.4 Key word .Anti-wear oils7.5 Material Safety Data Sheets (MSDS) . Contracting o

26、fficers should identify those activitiesrequiring copies of completed MSDSs prepared in accordance with FED-STD-313. Thepertinent Government mailing addresses for submission of data are listed in FED-STD-313; and29 CFR 1910.1200 requires that the MSDS for each hazardous chemical used in an operation

27、must be readily available to personnel using the material. Contracting officers will identify theactivities requiring copies of the MSDS.7.6 Equivalent specifications . If the fluid is already known to pass the following, it should beconsidered acceptable. The specification numbers below are taken f

28、rom the Special Manual,Lubricants Purchase Specifications, Approved Products, Publication Number 10-SP-80160 bythe Cincinnati Milacron Marketing Company.A-A-59354 grade Cincinnati Milacron Specification Number1 P-682 P-703 P-694 P-54NOTE: This information is included because these are the industry-a

29、cceptedstandards in the machine tool lubricant industry.MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY:GSA-FSSCustodians:Army - AT Preparing Activity:Navy - AS Army - ATAir Force - 68(Project 9150-1240)Review Activities:Army - AV, MD, SMNavy - MC1, OS, SA, SHDLA - GS, PSNSA - NSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-